วีดีโอ

DeWalts easy fix to grease going everywhere is to pop the the plastic cap remove the fitting with the wholes and replace it with a regular bolt and no more grease leak

Didn’t know limp bizkit was a contractor too! Clean job you guys got some nice equipment

Nice work. Just put a bigger rock for a base next time

Great video ! I recently found your channel and it’s my new favorite

If you want that to last let it warm up well. Look up "2 stroke cold seize"

Needs 8 tooth and a skip .

Heads 17 pounds on a 395xp

Just a thought... leaf muncher

Why not......who needs snow.....thanks for the entertainment.

Doing a channel around this kind of trucking ... I BET... would get a lot of guys subbing!! Would make for a VERY interesting channel and I would definitely SUB!!

You think it's bad in that truck... now do it in an 86" Studio Sleeper!!

There are a LOT of BRAIN-DEAD people today!!!

It's not really the 4 wheeler's fault. It's the powers that be who could make drivers get better training to get their class C license. But NOOOO... they don't want to do THAT... cause many people may not pass and then you have less people going out to BUY THINGS!! But this goes deep.

Your suppose to warm it up first..you will ruin it doing that

Why didnt you put a hose in your gas tank.and fix it..the hose must have a hole in it.or your saw needs cleaned out..and its causing it to over heat and boil the gas..

i put a cheap amazon split screen bu camera on the end of my 30t trailer and on the roof of my w it changed my life!

safe to assume you tipin the scale @ 135-140 k with that monster?

You guys didn’t plan your route very well, and on a narrow road we always have our pilot escorting the wide load he can get traffic to pull into the wide spots just better control of traffic. I can see why you said ppl have hit your trailer before. Very poor planning all you do is complain about everyone else instead of fixing your own f:ckups.

If you're worried about burning through, you can just heat a spot ~the size of a nickel to white hot at one end of the bearing and drag the spot to the other end. You should be able to drive it out with a punch after thoroughly cooling it.

What I do on a tight corner like this is hang close to the right and go past the point where you would turn about ten or fifteen feet, now reverse with your steering wheel hard to the right (jackknife) now go forward into your left hand turn and keep to the right and the trailer should make it around the corner

Thanks for taking time to film, explain, and post!

Nice job! 😎

The easiest way I've found to get shims in place with new pins is to use the old pin from the other side and work the old pin out with the new pin, shimming as you pass through the joints.

Nice job. That press makes it a lot easier.

"Do we have everything to do this job?" --- "Well, it's not a Caterpillar shop, and we don't have everything we want, but we do have what we need." This is how a lot of us get it done and I'm glad you posted this video. Hopefully, it'll inspire other guys to jump in on their own projects like this. As I was watching you fight with those shims, I was thinking to myself... "Dude needs a port-a-power to ease that pressure just a few thou." and then BAM !! it appears... Great job and fun video. Respect from Georgia! - Cujo

Cool video! Wow that press was impressive…😳👍😀

Good stuff...been there myself.

Just taken a quick look at dump box , polls for the trap and and condition of the wheels and tires looks in purity go condition, ur not going to run coast to coast a local jobsite and quarry.

diesel on a paint brush over all the greasy area then cold pressure wash will clean it up, nice work turned out well

Well done, this kind of thing is always a lot of work! I always hammer bushings and pins with large sockets, never used a small punch like you were doing but is seemed to work. I made a 1/2" square end on a old crow bar for mounting the sockets that i don't mind hammering as i got sick of messing up extensions, haha.

Awesome Video 💪

Got it done.

I enjoy this video, I felt your pain, because I work on my own vehicles.

Also if you have an air chisel it works faster hammering out the bushing. Mine was broke at the time of videoing.

👍👍👍👍

Looking for the comments that say they couldve got it in there in one shot

Anyone know if the 460 has a summer/winter mode

I liked how slowly you explained everything thanks

hello im thinking i want to start my own machine and do this service, but could you give me some advices? is there anything i need to know before jumping into it?

Nobdy likes a sloppy hole LOL

There was a recall on them for a faulty seal on over flow valve and they stopped making that one and there generation 2 of that one that's way better but that DeWalt your using now lasted me for years and I had to send to DeWalt for seal recall and worked way better after

Of course you had to show the 33 for the freemasons for the sicko demonic lieng loser devil the sicko devil minion as those leaders gov tags on the truck . i got eyes to see by my beautiful Heavenly Father Almighty God The Most High,Christ with the Holy Spirit in these end times back in days of Noah

😎

I live up here in the Colorado mountains. I'm going to buy a skid steer and do driveways during my retirement. I also noticed that no one up here uses gravel in their driveways. We do have tons of pine needles, but I have to say that black gravel on top looks real sharp. I have a long driveway to my house and around my property, I'm going to do the gravel thing just to get some practice. I'm actually amazed that no one does this to their driveways, it looks so much better. You are doing a great job with this project!

Awesome video! Young drivers could definitely learn from this!

old car hack put some pepper in it maybe it’ll block up the leak lol

I'm surprised the libtards up there are still letting you run those pre emissions trucks lol

Good and nice video man 💯

Damn you really don't know sh!t about saws. You were running with the choke on.

Huh a simple walk would solve hitting stuff. When things are in the way dont spread just drop when open spread...