วีดีโอ

for medium roasts you do not need more than 6 bar

sheeesh

Basically insulating it with a big Mr Clean Magic Eraser, lol. It's all melamine foam.

Hi! I've installed the OPV and have since seen other potential improvements for my Oscar 2. You were my inspiration to do it! I have read up on modifying the flow with a Synesso ruby flow restrictor/gigler at the solenoid valve, removing the 0.7mm gigler from pump (07300860), installing a 3.2mm gigler on a hot side of the group, and relocating the original hot side gigler 3mm (07300225) to the cold side of the group Have you tried anything like that? I tried to replace the 3.0mm giglers but the nuts on the copper pipes are stuck. I assume there is calcium build up. I don't want to break the copper pipe to open it up. Any suggestions? Thank you so much for the great information and your help!

That's the expansion valve. The opv is on top of the boiler.

Life pro-tip: don't wear that hat. Especially indoors.

Nice tutorial! Can you tell whether top and bottom blades are the same?

Hey I remembered your videos about you Oscar 1 and I actually have one I’m trying to sell. Do you know anyone who would want one or where I might have some luck selling mine?

I only made it six seconds into the video. The loud bullshit and "bro" behavior is unnecessary and utterly stupid.

I want to ask... i have a simonelli oscar 1 coffee machine. is experiencing damage, can't produce hot water. please help because I can't detect where the damage is. while all parts are still in very good condition. thank you

Hey nice video! I was looking to do the OPV, antivacuum and the new steam tips. Did you find those mods helped a lot your coffee ? Cheers!

My espresso is watery do you think lowering the pressure will make it better. Water is way to fast I do a shot in under 8 seconds!

This is absolute trash. Terribly under-extracted, promotes bad practices like puck polishing (enjoy disturbing the pressurized puck with shearing forces), and uses dirty equipment. I hope to never stumble upon one of your coffee shops. That goes for whoever watched this video and unironically thought it was good.

Good demonstration, there's still a few more methods of distribution. An OCD or Jack leveler among others have shown good results. One of your contemporaries found that comparing four methods the highest extraction was from the good old three taps a finger swirl and tamp. One popular channel has gone to only a Jack leveler and no tamp. Simpler is better.

How do you take the motor out what way does the nut turn

Why all videos shows te machine areado open and prepared?

an electrical screwdriver allow to tigtne moderaly and with even torque . No need to tighten too strong indeed, it may damage the thread or bow the burrs a hair. Checking surface parallelism may be neessary in case of rough noise when they touch.(like here) the noise should be soft (Saico information, Mazzer too told me that) SMall aluminium foil shims can correct any undue position. th-cam.com/video/5-cf0Iack5Q/w-d-xo.html

Kindly advise how to increase the coffee brewing temperature as the pressure switch screw is glued and cannot be turned,Thanks

Great tips and very thorough , pull some shots now

Dope gotta try this out. Thanks for the info ✊🏽

I love that you can mod these 🔥

Super clean. I need one of those 🔥

Great content ✊🏽

Dope

Hell yeah 🔥

Crazy!!!

That was trippy lol I felt like I was a baby and Reezy was carrying me around 😂

Man I’m on the hunt for an Oscar. So dope

Dope video 👌🏽

🔥🔥🔥

You guys always get the good stuff 🔥

Super interesting. I need one of those mugs!

Super helpful bro. Thank you!

Great video bro 🔥

Super cool video! Man I’m loving the custom wrap. Where can I get one?

*Awesome machine that makes creamy espresso and dense foamy steamed milk.>>>**t.co/cVSsqtbwMs** Awesome machine for the money.*

Man your machine needs a wipedown, lots of coffee stains, you counter has some coffee particles too where you put the paper cup cut out

Do you have a descale routine for the Oscar? Mine is long over due for sure

Isn't the doser in your grinder already breaking the clumps? I think it's the only reason to prefer such a grinder (for home use) over a doserless one...

Love it, make that black gold.

Hi. Is there Any difference on a simonelli Oscar 2005 vs one from 2010? Does it pull just as good shots ? I bid on one from 05

Are you guys still gonna giveaway the espresso machine?

i removed the upper part of the swiping part and only covered the screw with upside down plastic funnel...

I was hopping you were going to do a vid from the beginning... It's 2 late now!!!

crazy you say my minds playing tricks on me, and that song is somehow on the radio as i watch

damn....scotty is a hustler. talking bout slangin to the bums. ima need that money too lol

How about a cold brew video? Nitro cold brew or something different in the cold brew type.

100% going to try this! Thanks

OK, but plastic generate a lot of static, that's why your ground coffee stays on it. Anyway, good tip. Make us think about a solution.

Hello mate ! Can you do that on a factory machine or you need to upgrade parts inside first ? Thanks