วีดีโอ

Hi what size and thickness box steel did you use?

So it putts along barely with a 30kg kid how’s it handle a fully grown adult or bigger person. I realize it’s old video but you’d be best dropping a 60v-72v electric motor like there using in sur-Ron’s or talaria’s

What a clown hes on the grass trying to re join at speed 🙈

"Cars to the right of me cars.. to the left... i'm stuck in the middle again" ; "Aim for where they are; they'll be gone by the time ya get there."

your’not gonna last long , under the jack & pr😂carious block

very good vid, my main engine pulley doesn't slide down, would you have to hit it hard to release it

This is valve train rattle

Great driving. Stayed cool, brake, move, accelerate. Perfect.

Nice survival skills sir!

The worst part about being in that situation is that *you* can see what's going on directly ahead but people behind might not, so you're just letting everything unfold in front of you while hoping you don't get rammed into.

Very useful video which helped me swap the transmission belt on my Atco GT30H. However, my clutch was rusted onto the crankshaft, so removal was a pig of a job, as no place to fit the pullers on securely. So its was a case of tipty tap and pry bar off the clutch very carefully as it has a cast ally case. Re-assembly I found best done by putting clutch and deck pulley together off the crank, and then sliding onto the now clean and geased crank. Best of luck to all trying, and thanks again for the above video.

How do you tighten the belt to stop it slipping

Man you dodged that like an oracle.

thank you

'Promo SM'

Handy for references same as castle garden 140xs thanks

Great job mine just spat out a belt, very helpful thanks

After drive belt change the starter wont engage?

excellent . My only comment is you forgot to mention it is identical to the castle garden .which i have.cheers and can now fix

I want one even more now.

Damn, great situational awareness to check up and get through that mess.

This video has helped on more than one occasion. Don't suppose you know what would course the deck to stick down?

THANK YOOOOOoooooouuuuuuu :)

Many Thanks !! You a gentrleman . Just doing mine today . I owe you a beer !

How many nm of torque do you need when putting the clutch assembly back on the engine?

Nice drive

😢 gutted that you had the failure

Good video,Saw that most of the parts are the same or really similar exept hood.Used it as a base for Stiga 2084h and got it done in 1h for the first time.

how many erm, s did you say

You can do the screw driver test. Place metal on engine part. Ear on handle. To identify area with knocking. Sounds normal to me though.

I really appreciate you making and posting this video. Helped me understand exactly what was going on with my old 2005 Mountfield 1236M. A couple of minor design differences to mine old one obviously but generally the same procedure. Thanks a lot; greatly appreciated.

Cool as fuck - where’s Melton? 😅

Tappets cold

Cool exactly what I was looking for

How do you remove the drive belt reel under the motor, the one at the front, aften you have removed the bolt ?

Now seen your notes re run out of road/time

What happened in race 3 as my video ends before finish

Hi, great video, any idea on the belt part number or length?

p͎r͎o͎m͎o͎s͎m͎

Poorer start than usual makes for a good video as you recover. Great weather

Excellent vid. Thanks. Helped me out with the 1638H. Couple of differences. There’s a fan on top of the gearbox at the back so I put the belt over front and back first. Then lastly put on the spring clutch pulley (bit fiddly but manageable). No need to remove the front engine pulley on the 1638H, just undo 10mm bolts on the port side of the pulley and slip the belt up. Hope that makes sense.

Great Job. Just looked at my belt as it was making a lot of noise and its got lumps missing out of it and cracked all over. I did notice that the belt goes slack when pushing the break down. I will be following your good advise.

I kept you on your toes in that race.

Great video, that's helped a lot, thanks!

I have a Columbia which looks similar so this is very useful thanks

How do I remove the blades on a Stiga 384m. Thanks

Hero - same as my Atco GT30H where a pulley seized and chewed the transmission belt. Answered my question regarding getting over the clutch assembly :)

Nice one. Very useful information. Thank you

Thanks so much for posting. Very helpful indeed. Thank you for your help.

Just what I’m looking for and very well explained I have the exact mower 👌 would this be the reason for it slowing down in higher gears on hills? Is there anyway to adjust this or checking if my belt needs replaced first ? They seem to be very pricey for genuine part .. 🤔