วีดีโอ

Hello Welcome Good morning Sir you re a very Good and great very nice you machine Crusher

Hello Welcome Good morning Sir you re a very Good and great very nice you machine Crusher

Great content! Looking forward to seeing your progress!

"Elelater go down the hoooole"

This is by far the best nico tutorial I have seen yet. Thanks.

Great video! Thanks, for showing every step only once, instead of showing 4 x the same! It makes looking this a joy! Well done!

Good job making box joint supers and deeps. These will last 20 years and more. Pre-drill all nail holes, use water proof glue if you have it. It will seal the wood from moisture. A simple jig like this is all that is needed and keeping focused as to what you are doing so you don't cut the wrong part. Thanks

Oh man I cant wait to see more of this in the future thanks for sharing!

Угол упорной пластины ,скорее всего, не тот,нужно точку опоры смещать выше прижимной пружины.

I would combine any of the weaker ones that you don't think will make it and feed, feed, feed. Invest in some hive alive fondant patties or similar.

Thank you for sharing your process. Very streamlined.

Can you share the link of these things, because me to i want to buy

Thank you

I loved watching this cut out. It's annoying when you go to watch a cut out video and they don't show you the actual cut out. They just shoe you the start and then the empty cavity and then the relocation. Sometimes people click on a thumb nail that says cut out because, strangely enough, they want to see the cut out. Thanks for showing the actual cut out, although not in entirety. May I suggest you fil more of the up close camera footage? Or film all the footage up close? The up close camera footage is amazing because we can actually see the bee behaviour and their colony, brood, honey ...everything. That's what is so interesting, the bees and what they have created!

too bad the "save" button is disabled, I would love to save it so I could come back and re-watch this great tutorial

simple and best

Outstanding work sir. Thanks for sharing.

Excellent video. So helpful. Thanks for all your time and work to create it.

Good video. I'm about to start with the nicot system.

Great series, you do a really good job explaining it all and making it clear- If you were going to build it again would you change anything?

Very helpful - thank you for posting this!

I build them somewhat the same. But no special top cut. 3/4 all cuts. And do the top corners opposite of how you set it up. So no adjusting my dado.

My man! These videos have been extremely helpful. Thank you for making them!

That's too cool 😊

Happy for you! Still waiting for the first swarm here. Unusual for me not to have caught any swarms this late in the season. Are your bees ahead of schedule or on time for swarming?

If the end boards that have the frame ledge had the pocket instead of the pin at the top you wouldn't need to make any adjustments. It would just be a full depth normal stepover cut. Correct?

Loving this amazing playlist! thank you very much, I wonder how did you just put the nuc frames immediately into the hive like wouldn't there be a fight?

Hi I have used the nicot system for years and had good results, but to get top results when you inspect your hives weekly save the Royal jelly from Queen cups in a small pot so when you have positioned your queen cups in your cassette using a cotton bud dip it in the Royal jelly and from the front of the cassette holes push the cotton bud covered in Royal jelly in to the cell touching the cup bottom and turn to add the queen jelly substance and odor into the cell bottom, this will increase your queen cell take by 50% more. Regards Paul.

Thanks for sharing! Nice job.

Thank you so much, perfect man. L o l❤

Great video and just what I needed. Thank you!

Good Stuff! Well done!

With the box on the floor and the handles up to the sides mark the angle on the bottom of the 2×4's and counter sink the nuts,wouldn't that help with the hight problem picking up the box? I'm going to try your idea by copying wheelbarrow handles and a hinge. Thanks for sharing ✌️

Do you need to wire the plastic foundation?

You should got up close to show more. Good video tho.

You are awsome! I am so very tired of using my router to make my boxes. Thank you for showing me how to make a proper bee box!!!

Very nice but why you don’t use the board to all four sides to band the sheet?

Planning on using this in the future

That works. You have given me all the info I need to repair or build a new cover. Thank you for the BOM and detail construction.

Is it a stainless steel mesh?

Wow, I like how organized you were throughout the whole process. Thank you for your time and God bless.

Well done, on both the woodwork and the video. Thanks for sharing!

Awesome videos. Thank you

Great video!

Thanks Charlie! I need to redo some rotten hive stands this year and was thinking about a similar set up. Happy beekeeping!

great video. May I ask what screen size you uses? The hole size of the bug screens are about 1.6 *1.6 mm but varroa mite itself is 1.7 in width. So they can hold on to the screen even if the hole is 2 mm. I can't find a screen with holes of 2-3 mm.

Is there reason why you replaced Queen excluder between boxes when Queen was already inside the Nicot cassette?

Fantastic instructional video. I love how you combined all the day segments for each step. I’m actually trying the Nicot system you described right now, and am on day 4. Thank you very much for being so helpful.

I'm ready to make juw crushed

I will try it your way now.