- 7
- 43 487
Hakunen
เข้าร่วมเมื่อ 10 ม.ค. 2023
Autumn winds in Finnish archipelago
Heading to mainland from outer islands. The boat is KS1030(Keihässalmi) with Perkins T6.3544M.
มุมมอง: 575
วีดีโอ
Twin Disc MG506-1 Overhaul. Workboat with 240hp Perkins Range 4.
มุมมอง 3.7Kปีที่แล้ว
Overhauled my workboats Perkins engine a couple of years ago. This time it was the clutches turn to get serviced. New bearings, clutchplates, piston rings etc.. The boat is a Finnish made KS1030(Keihässalmi),weighs about 5 tons. Also seen is one monday mornings boat ride going to work in fresh winds. Enjoy!
A ghost on surveillance camera?
มุมมอง 17Kปีที่แล้ว
I have a few Kuvasz dogs and I installed these cameras here and there to keep up with their doings. Last night one of the cameras captured this clip. Dogs were barking inside the house and woke me up. This is not something unusual with this breed so I didn't think much of it. Just for the curiosity, there used to be a wooden extension to the house where this "ghost" came from. The previous owne...
Hettich W51 Wall clock movement. Relaxing clock ticking.
มุมมอง 191ปีที่แล้ว
Old german wall clock movement. Needs some cleaning, but works perfectly, and has not been used in 40 years. The clock is on auction on Ebay.de.
Yanmar 1GM Fixing leaking water pump, bleeding the fuel line, test run ok.
มุมมอง 11Kปีที่แล้ว
I had a Yanmar 1GM sitting 20 years on my workshop shelf. Decided finally to sell it, and serviced it for the new owner. New oils, new filters, new sink, new impeller, checked the fuel lines. The engine has run only about 300 hours so far. It started and ran ok, but I noticed the water pump was dripping. So I ordered new lip seals and fixed the pump. I thought somebody might wanna see my way of...
Perkins T6.354 Range 4 Overhaul. Workboat engine Before and after Rebuild
มุมมอง 3.3K2 ปีที่แล้ว
I needed a workboat so I bought an old fishing boat with an old Perkins 6.354 turboengine. It was in need of an overhaul after about 10500 hours runtime, with oil and fuel leaks and quite substantial blowby . I used it as it was for what was left of the season and took it in to my workshop next winter. I wasn't planning of making any video of the rebuild back then, so the process is covered wit...
Yanmar 3HM35F
มุมมอง 8K2 ปีที่แล้ว
Engine was in a sailboat, low hours , under 1000h. The boat went to scrapyard and the engine has been sitting on a shelf for the last 5 years. Engine and transmission oil changed, new anti-freeze in the fresh water circulation. Test run 10.1.2023 was fine with no problems whatsoever. Transmission KBW10, 1:2,83, also in good condition. Engine is in South-West Finland. This engine is sold. (17.1....
Several very useful non-obvious tips from someone who clearly knows what they are about.
i have a perkins 200hp turbo and the oil line busted and the engine shut down at sea, I fix the oil line and changed the oil and filter. the engine is running but now I hear a knocking sound, do you think I need to rebuild it
Maybe move out of your garden shed to a place with actual lights so we can see what the hell is going on. And ALL threads need prep, either grease or Loctite.
Nesecito una trasmicion
My man. You have no idea - you are the ONLY ONE among dozens I've tried to follow the steps of who properly described every relevant step. Specifically, the part about the larger seal not being ment to slide in too far is completely missing from every other guide I've seen and I've been trying to solve this for months. You are a hero!
Thank You very much. I'm happy you found this video helpful. All the best👍
Tavaraako kuljettelet vai muutakin hommaa?
Rakentelen saarissa sulan veden aikaan, uutta ja vanhaa
@@Hakunenko varmaan mukavaa hommaa kun saa veneillä samalla.
@tujuprojects meneehän se tässä. Talvella sit mantereella
@@Hakunenko laita lisää videoita veneestä ja tekniikasta jos jaksat.
Good stuff.😊
👍 Kiitän
Hola muy buenas tardes saludo cordial deseo saber que elice es la adecuada para un motor cumming de 400 hp y una trasmision de 4 a 1
Thanks for sharing
GREAT video. Thank you!!!
Thank you👍
Great video. Where do you order your lip seals from? Cheers.
Thanks. Lip seals usually come from local shops, sometimes from UK if I have ordered bearings or some other parts to these projects.
@@Hakunenko Thanks for the reply. I am in the UK so I will do a search.👍🏻
@SCCFORUM If I remember correctly it was Simply Bearings Ltd the last time I ordered lip seals with some bearings..
Thanks for the video!
You're welcome! I hope it was useful!
Your video is exactly the information I needed. Thank you so much. Even if not many people see it, it is a huge help to people like me. Please keep telling your story. I will come see you often.
I'm glad you found it helpful. I'm too busy with other things, but manage to make these videos every now and then.
Qwantuz HP? ?
240
Valor
👍
Máy còn không
Sold, sorry
Please advise on how and where to access parts for this engine?
I ordered everything from En-Gen diesel products. sales@engen-diesel.com They're located in England. Very nice service and competitive pricing. I hope this helps.
Looks like mine too!
Hmm. Maybe he's on a visit.. 😉
😂@@Hakunenko
This is like watching somebody filling an aquarium ... .. ! My BP went down after watching the whole video, thanks!
Nice! 👍
Hello. Do you know if the seal is TC (Double lip) or SC (single lip)? Thank you for the video
Hello, these are TC seals. Right sizes are 8x22x7 TC (NBR) and 8x18x7 TC (NBR). Don't have to be nitrile, but I recommend it.
My friend, I have been having troubles with my fuel bleeding system after the tank ran dry and I remembered last time there was ONE video which helped me fix everything and it was yours. Took a while to find again but it works again, so thank you VERY MUCH!!!
Thank you, I'm glad this video was helpful. Sorry about the audio, I'll try to fix the levels in future videos.
🌟 Promo sm
Thanks👍
Quanto q e un motor deses
Isto xa está vendido, perdón
Hi there. Was there a specific kit you worked off to do the rebuild?
Hi, no specific kit used. I ordered all the parts I needed from UK. There was some special tools for the job but they are virtually impossible to find so I had to make them in my workshop. The service manual is a must of course. It gives you the wear limits and other instructions, part numbers etc. Good reliable engine, definitely worth overhauling.