วีดีโอ

심지어 나는 서랍칸 가득 채운적 한번도 없고 하루에 한번 비운날도 두 번 정도 뿐이고 항시 바로바로ㅠ치워줬음 아마도 암앤해머 탈취제가ㅜ문제인듯함요 청소하고나니 마스크 스고했는데도 내 코와 입에 암앤해머 냄새가 숨쉴때마다ㅜ나네 파우더 탈취제 절대 리터러벗에 쓰면 큰일납니다 서랍칸에더 뿌리먄 안돼여 그 서랍칸에 센서같은게 세개나 노출되어있어서 절대안됨 나는 왜 리터러벗에 냄새가 난다하는지 다 게으름 피운다고 생각했는데 탈취제를 쓰면 고장날 구조 삼개월 탈취제 가루형 같이 쓰고나서 한 연식 십년은 돼보임 뜯어보니깐

아니 내가 기계치라 모르는거야뭐야 분해해보니 너무 더럽고 고장안난게 신기할정도로 뭐라고하냐 센서???? 그...막 용접된 초록색보드 그게 엄청나 많은데 다 노출되어있더라ㅜ투명한 칸막이 대충 둘러놓긴했는데 3개월쓰고 고장안난게 신기할정도면 심각한거 아니야 이거 매우 심각하지 드라이버로 나사푼것도ㅠ아닌데 나사풀면 얼마나 심각할지 고장이 나는 한이 잇더라도 나는 나사풀고 봐봐야겠더라 대충 분해해봐도

Getting kinda nauseated with the camera moving around so much

😊👍👍👍

The green DFI sensor that you're talking about is the older version that people have a lot of problems with. If you look online you'll see the newer one that they have out that one I would recommend, it's called "DFI Kit + Pinch Detect". Just in case you clean it and it goes bad and think you messed it up a lot of times it's just an issue with that part.

thanks for your video very helpful.

Does anyone know the position of the 2 magnets within the 3 slots of the bottom globe under the rubber mat area. I took the bottom globe apart and they fell out. Not sure proper positioning of the 2 magnets within the 3 holes. Help please

Your nut goes on the inside and the screw goes up into it. At least that's the way it was when i got it. I just replaced the liner.

This is the only video I've seen where someone removes the inner plastic thingy with the plastic mesh on it. I need to do that becuase I can clean the inside thoroughly but stinky litter is still stuck under that thing. I cannot figure out how to remove it. Honestly, If I can remove it I dont think I even need to take it out of the globe- I just need to clean under it. Q: Are the only screws you need to remove it are the 4 around the that hole/window? I usually clean it in my tub- but now that it's warmer I can do it outside....except the hose water will be ice cold and I typically will soak the inside of the globe in hot hot water when I clean it.

Hard to watch because the camera a moved too much. Would have been good though. Thank you

I connected the cover inside to the top piece before I assembly bottom and top of egg together.

Thank you lady I needed some guidance on disassembly and the video helped 100%!