วีดีโอ

How do you zoom in ?

When I export my G code and go to run it on my Genmitsu 4040 Pro through UGS it says my spindle speed is zero, any thoughts please?

Hi Seth, I have a problem and need your support please. I have a cutting machine that uses a CNC software that requires a keyword to use the software that I do not have. My question is; is it possible to delete the software that the machine is using and install another one similar to it?

what is software used to draw 3d and software to get gcode

It didn't work I watched the video over and over , it cut out the depth but when i went to change the bits to carve the face it didn't work. :(

Seth My Z axis is cutting deeper than my file indicates?

Great tutorial! Thank you for this!

HI. i have just changed my XPro V5 to the Openbuilds controller and limit switches. I have managed to calibrate my machine (Bulkman 3D Ultimate Bee 1500 x 1000) but I am not able to get the limit switches to work at all. Please could you help me to activate them in the software.

Does the free trail include the foxalien 4040xe

I would love to see a probe tutorial. I have a simple gemitsu 3040 controller and triquetra 3 axis probe plate

CNC hot wire machine kaise khariden

Is machine ko kaise purchase Karen

I'm using open builds to operate my homemade CNC table with a MKS DCL v2.1 card. Everything is going smoothly so far. My control card has built-in Wi-Fi and I'm wondering if you could tell me how to enable it using open builds control? Thanks.

I'm not seeing the union on esael

Can you please explain that interior perimeter scoring? Would that be right the bit also?

Being a first-timer to hook up a control card and a stepper driver to a home built CNC machine I have to say this video made my day. I plugged in my MKS DLC 32 version 2.1 card after installing the software, hit the jog button and was delighted to see the axis move. I used open builds cam software and was trying to figure out how to install grbl to control my machine. I meant to check out open builds control but totally spaced it out. Super happy I came across this video. So far I like everything about open builds. I've ordered parts from there. They responded to my questions. And their software is great. I look forward to digging into this open builds control software and getting my configurations correct. Thanks again. Subscribed.

i will buy this machine please contact

This guy has a lot of knowledge about these cnc programs, there is no doubt about that, but his videos are very boring, he needs fluids.

Just a word of advice. Maybe you should rehearse your videos first. You are regularly distracted and fumbling around with your tech. It makes it extremely difficult to watch an hour video that for all intents and purposes should be 20 minutes.

Can this be used on 3018 pro cnc

Best to take down a deprecated machine/website link. I'm not sure what happened with FoxA, but sad to see they dropped this. I've already staged up a 1000mmx1000mmx1000mm caged Foam cutter myself and have been very happy with the results.

I spend a million years screwing around with my 60°. I swear I've been using the same bits for 6 years now and it still crushes my souuuuuul! Any tips you have for that?? (The 1108 Amana 60°)

Thank you. Good stuff.

What about the $132? Default shows 152.4 mine seems to be $132=100.0 What is that one for? and should i change it to the default from inventables?

I use the x32 blackbox with interface and it says idle. when i hook to comp usb it says grbl disconnected everything was fine until i connected to the second cnc it has the same set up any ideas ? Thanks

You said a compression bit... specifically which one?

I'm having issues with inconsistent z height. I've been using the x carve for many years, not new to it. It's not the issue your describing because I've already checked that. Work piece is surfaced, brand new surfaced waste board, bit isn't slipping, all the variables have been covered. It only seems to happen on the detail pass with a v bit when there's a lot of required up and down movements of the z axis. sometimes it goes too deep sometimes it goes to shallow, by a significant amount, floating 1/8 above the surface not even touching. I've been going back and forth with support for months. They sent a new Derlin Nut saying there was a faulty one on some of the upgrade kits. Who knows. The tension screw on the bottom of the new derlin nut that came is lose, no lock tight, the nut is free spinning and the hex screw isn't even touching the opposing side, so there's no specific setting to it, it's not serving any purpose right now. Prior to it arriving I was told by support not to adjust that screw that it's preset to a specific tension. But obviously it's not preset to anything which now has me worried this new derlin nut won't solve anything. Any ideas? I purchased the upgrade kit about 9 months ago, never had issues before then over years of use. This issue is definitely tied to something with the new upgraded z kit.

You have a very deep voice, considering what you look like in the thumbnail.

That saved me a lot of time thanks!

thanks

OK, yo introducing the 3D builder tool has solved a problem I've had for like 6 months now. Thank you, Seth!

hi, your video turned out great! I’ve had the machine for less than a year and everything was fine, I adjusted the string tension, temperature and speed. all was good. But a couple of days, in places where the string passes simultaneously along the X-axis and the Y-axis, small waves are visible on the cut material due to the fact that the string vibrates. square shapes cut fine. but on rounded forms a problem appears. maybe you can tell me how to fix this?

New to this I’m trying to connect to my arduino the wizard says hold down the mode button and then the reset button where do I find the mode button

Connect 4?

I'm not sure why Amana didn't include a more positive indexing feature. One of the advantages of inserts is that if they chip or break, they can can be quickly replaced without needing to adjust anything on the machine. This just seems like a lazy design by their engineers. Didn't get me wrong, I love the cut quality I get from mine, but there's no excuse for such a (usually) amazing company to have such a fiddly tool.

Hi, great video dose open build support 4 axis?

bla bla bla blaaaaa nuda

what kind of cnc do you have? I'm looking to get one maybe a queen b.... not sure

I just found this video and went and checked my settings and they were wrong. Makes sense why when I would move my z axis up and down it almost had a grinding noise. Once I changed that setting that noise went away and it moves much smoother. Thank you for all of your videos as I am just finding you on youtube. I have some more to watch now.

Hey, can anyone explain why the z zero at 34:36 was set to the top of the spoil board and not the top of the material?

Hi Seth can you do a video of setting up open build on the genmitsu 4040 because I Can get ot to connect but Carnt get it to jog the home button don’t light up but I can turn on spindle so could do with some help because I would love to use it

I'm new to this. I did everything and it says 2 to 3 hours for roughing. What do I do to speed it up? thanks

Wont connect to a smoothie

Sorry you should practice your instructions before making the video. It is too hard to follow.

Hi. Where can I purchase a machine like this? Please help me

... What were you carving??

this is not in the 3D carving

how is it done in the 3d mode

Beer caddy

most wood i use is 1 inch, is there a way to get image quality and make most standard thicknesses less?