วีดีโอ

where do you get the framing for the shower?

Does anyone have a recommendation for what type of double sided tape to use?

Thank for a very helpful post

Just scared to make a mistake.... I'd rather have you do it

Perfect. Thanks

What size of glass is this window and thickness as well. Mines looks exactly like it.

Very helpful Thank you !

Where can i find that block?

I never listen to you again you don't tell nobody how you supposed to take the door off but I listened to you and I screwed up good baby

Did you drain the oil?

My buggy heats up and as soon as i give it gas temp start to decrease until i let it idle again for a little ideas

Where is the bleed screw

This video is the best. I watched several other ones that were just ads for companies or just not not clear. What if I have a small window that's extremely hard to access due to the pitch of the roof? Is there a way to do this from only the inside? The window is 1/8TH the size of the one in your video but it faces the street and my HOA is on my ass.It's filled with discolorations. Thanks for posting this excellent tutorial.

Thanks for this. I replaced a pane of glass in our garage window that had a piece of chopped firewood fly through it. Not ideal. Replaced the old glass with a piece of used plexiglass I got from the local ReStore for $15 and your tutorial was exactly what I needed to get the job done. Awesome! Gotta love TH-cam University! :)

Thank you for this video

I’m surprised the glass didn’t pop on you when you were prying on it that’s the easiest way to break the glass never use metal on glass

thank you for the video 😎👍

Really a great video. I have a similar, older sliding door (not exact to the one you show) and I know the rollers need to be replaced. I was planning on pulling the doors totally off, and this will save me a ton of time. I've also made the mistake over the years of using regular WD-40 and the tracks are filthy and dirty and the dirt is now caked up. I'll use silicone next time. Thanks!

Where r u located?

My outside glass needs to be replaced, but the inside glass is not broken. Do I have to replace both??

Old Shock does not come off

Update. Got the harness apart but after having to hammer the aluminum bushing into place, dropped tail gate on its corner. Worked for an hour trying to get the piston off. No go. Hinge seems seized too so now tailgate only goes down part way and the drop cord on the right side won’t stay in place and have to move it to the right everytime I close the tailgate or it won’t close. Nice design Nissan!! Never had so Many issues with any other truck. Last Nissan I buy.

I tried to get the wiring harness apart. You said it’s pretty easy. No it’s not. After 2 hours I gave up. Really wish this was shown more clearly. I pushed down on the backside of the clip but no way would come apart

Great idea to use marine carpet on the ceiling? What size did it come in and where did you purchase it from? Thanks!

I broke one pane of my window but the other one is intact. What would happen if I simply clean out the broken glass and run it as a single pane? This is in an outside room, so I'm not worried about insulation.

You seriously made my day! Can't believe how easy this can be. Great video, thanks so much 😊

There is a ~1" spring for the oil pressure regulator that is not mentioned anywhere. It will likely fall out when you go to remove the cover. Probably best to remove the bolt holding it before removing the cover. It takes a T55 and sits just under the oil filter housing

At 1:51 how do you get that oil line off? Is the clamp re-usable?

I need some ideas please...installing a custom replacement IGU in a stationary transom window off a ladder above a door wall. Inside temperature is 70F, outside is 45F. I will scrape the residual old double sided tape with a multi-tool + thin blade, painters knife and a bunch of patience. Planning on using 100% silicone caulk/adhesive on the perimeter side-face of the IGU (had it made slightly thicker to compensate for not using double sided tape). I am going to use two double suction cup lifters to set in place the 25lb IGU. Any thoughts on how to temporarily hold the IGU in place while the sealant sets up? Don't want the IGU to fall out on me, or the floor, or break. I am not sure the glazing beads alone will hold it in place as they are kind of flimsy. I have done sliders and casement windows flat on a bench in a work shop, this is my 1st stationary IGU replace job. Thanks for any tips.

Wow what a great video! thanks some much for sharing your knowledge.

I would never go 10,000 miles between oil changes. Fluids are the like blood of your car/truck. Spend the extra $60 bucks to save thousands down the road. I change at 3,500-4,500 miles.

Great video and love the bird sounds we don't have that at my house at 10,000 elevation in Colorado

You need to verify the measurement is from inside or outside, some replacement companies require outside of the frame measurement not the glass side.

Thanks you saved me a lot of time

very good demonstration : )

It is amazing you mixed all the bags for the floor!! I have done a 2x2 square and that was enough for me!!! Great work ethic!!

Throw a skid plate on it so you can grab 2nd and pin it but hell ya that’s tight

Great video. Thank you for sharing!

I have a 15 window light kit to replace. I assume it’s much the same as it’s one piece of glass. I just got the replacement kit. Am I correct ?. It’s 22x64 standard size

Do you keep rubber gasket materials, rubber glazing stuff in the van? Or is it all unique to each window brand? Just curious what you do when its in bad condition, maybe just silicone?

Very good instructions. Appreciate it.

Awesome job! 👏 What did you use to anchor it with and how did you anchor it down??

Freaking stupid

Wow, just wow, best freaking video EVER, thank you a million times over.

Direct, to the point, great video. Thks

THank you I'm working my into trying to change gkass. I have American craftsman bow my stionary pane is foggy. Window glass Warranteed but no for installing. Im afraid to try.I don't have pieced ti snap in on outside looks like it sits in feame. has inside covers. I cannot find video for my window so thanks

Perfect explanation for how to do it, I will try it tomorrow, cross your fingers lol

Thanks for your information about replace broken glass. I lost the corner bracket that hold frame together. Where can I buy new one?

bro, thank you!

Not a bad way off doing it but U should undo both screws in the door frame not just the bottom one as if U do it his way U are likely to damage the door frame so remember undo top and bottom screws that way U won't damage the frame.