วีดีโอ

Nice bro

This video was spot on!

Why the f*** is everybody taking the tire in the fender flare off and all this other f****** s*** to do the starter on their Chevy trucks you're doing way too much just climb underneath their disconnect the f****** battery take the two bolts out in the f***** I'll drop down and take the wires off put the wires back on put the f***** you're doing way too much for these videos trust me I've been working on Chevys way too long this is not how you do a starter I don't know where you got this information from but you're doing your way to God damn hard

How do you know you only need the motor and not the regulator or vice versa?

Why does it wait for 20 degree weather and blowing snow lol. Can’t complain tho I’ve owned this 2002 Silverado in Ohio since new. 250,000 on odometer and original starter.

Nice jam

awesome coop

Definitely want to sand down the contact to the starter for less resistance

La mía es igual a esa quedo 5 meses sin trabajar y ahora no echa agua que podría ser?

YOu made me feel like a pro today! I found one of these at the pawnshop and then found you... Thanks a ton!

Thank you for the video. Replaced the starter on my 2002 Silverado today. Much easier than I thought it'd be. Your video helped a lot!

Once I put the new starter in I started it up and it dies out once I put it in gear 2003 avalanche

Got wife's yoga 😅😅thanks bro😊

Got wife's yoga 😅😅thanks bro😊

Good, complete video. Thanks!

This video was right on time - thanks man

why does you're setup look dif then mine i have a 06 1500 5.3L i have nowhere near the amount of room you do

I put a new one on couple days after same noise

What is the name of the red clip your using on the TPost

Thank you!

What I don’t see in the last shot of the video, which is the thing that concerns me, is the coax cabling to the antenna. If the box rotates the antenna -with the cable installed - doesn’t the cable get wrapped around the post or twisted? Since the antenna rotates in just one direction and you continue to try to adjust the antenna over time, it will continue to be turned. How do you prevent that cable from getting twisted around?

My 2 cents. Never run a pressure washer without having a garde hose connected. Those seals in the pump will melt or crap out sooner than you think after they get cooked from running it dry(i found out the hard way)

Those gate swivel brackets are now 28 bucks. Insane increase.

Any way you could tell me the size bit you used to unscrew the oil thing?

Freakin genius! Thank you so much for putting this on the tube. This is exactly what I was looking for.

perfect

Quick, easy, and to the point. Thank you.

love how that AC Delco box says Detroit Michigan.... yet AC Delco parts are actually manufactured and assembled in mexico.

Thanks for sharing this. Helped me get ideas!

NO NEED TO SPLICE WIRES! Use the same wires by removingvthe inside of the socket that hold the wires in.

Thanks

Also any clue where this two wire harness goes

Hey man I have a question for you I just got one for free myself having sale issues but there is a tube right next to the pull cord I was wondering if there is anything going into that tube bc there are a lot of stuff missing so any feedback or pictures would really help if you still have it thanks again

Excellent, presentation

How did u do the hinge side. Thanks

Are any of the 2pin constant 12v?

can you tell me where you bought this latch with back plate.

Excellent!!! Replaced the starter on 2004 Rado (6/16/2024). No real issues but figured it was time. Easy process but a little tight getting in there.

Great video my guy👏🏼

Thanks for the video my man, followed these steps and had an easy fix

Thank you 🎉

what is the thickness of the cattle panel is it easy to cut to desired size, is it possible to give he dimensions of the gate and the panel parts to buy

Just what I needed. Thanks!

I have 2the this weed eater and I have a problem with the gas leaking by the hose that gos up in the gas tank

I like this method. I’ve watched a few different methods for wiring direct to the vehicle and this one seems the best choice.

Thank you for posting this. It was very helpful in getting what I needed to make my own gate and latch.

You rock dude. Thank you so much 🤘 hope have a great day

Perfect job on this video! My truck has the same problem. You've made this job easy. Thanks a million!!

What is measurement of the door ?

Now you can blind e eryone on the road!