วีดีโอ

Does a air con compressor turn consistently when on? As mine turns but stops for two seconds then starts again. Wondering if buggered or not? No cold air. Had gas refilled last Xmas, hasn't had much use.

Is this process the same for diesel and gas NPRs? And is the Cab heavy? That's the only part that puts me off doing it myself, especially after someone in these comments mentioned being cut in half at the midsection!🙄🤣

Messi😂

Oh! One thing I would change about this video is: Take the fill hole bolt out first to relieve the pressure in the pumpkin. That way you have more control at the drain hole.

I grew up on these medium duty trucks (you old enough to remember a KS22?). Still working on them 30+ years later. I appreciate your videos. Thank you. I'm going to look to see if you have one on doing the R&R on the 6L90 transmission. Thanks bud!

I have a 92 NPR dump truck. Set up with the 4 cyl turbo diesel. She still running strong. I am putting new tires on it. Thank you for this content 🙏 God Bless.

Have you ever had to splice a hardness connector I have a burnt one and need it fixed ?

Im looking to get a used model to haul my tools with random stuff, run my equipment, convert it awd and, tow my travel trailer being a daily driver. I was looking at the dump series but if i was rich id get a the overlander series

Awesome thanks

Thank you

Can you do a video on how much blowby is normal for a 5.2 4HK1TC, I have a 20111. it has some blow by but I am thinking its probably pretty normal, also whats a normal oil amount in the CAC system? I have some oil in my pipes wheres it come from? It doesnt seem like it comeing from the exhaust

Safety squints

What's the torque specs for the tie rods? Great videos. I am a follower.

I really appreciate what you doing here.

Tf was the tip mf it says in the manual to replace it anyway

Thank you for this video, it was very helpful. Can you do one for the AC belt as well? Thank you

Thank you again for your time and talent and making this video! I hope you come back to this channel and make more!

I appreciate your time and talent making these videos. I hope you do more!

Hey, @NPR Doctor! How can we reach you to maybe ask a few questions? Or better yet - I'd love to see a vicdeo about TIRE PRESSURES AND TEMPERATURES. I'm noticing on my NRR with largely an empty box, that I can get 20-30 degree higher temps in the rear passenger INSIDE tire, and maybe 10-20 on the rear outside. Any reapson for this, exhaust maybe? Road crown? Or is there an issue I need to watch out for?

simple ＆easy to understanding👍👍thank of sharering ！it really help alot💯

Great video

Do you have a radiator coolant flush video? Thanks a million!

Great video! Can you do some videos on replacing the front & rear brakes on an NPR?

How do I fix the Cargo light inside the box? My inside light switch does not illuminate with red dot when its on?

I really appreciate your videos, thank you.

Do you torque the stud's to 362ft/lbs also?

Is there a cable for the fresh/recycled air?

The bottom 22mm caliper bolt is a pain to torque. I had to cut a socket down to fit. I’m curious what you used. Thanks for making this video.

Thank you!!!

hey bro i like your repair videos just wanted to ask if you know the glow plug torque spec on a 4he1 isuzu engine.

Have you considered a video doing glow plugs? Maybe on a 07-09 4hk1 =p I’ve searched and there is one decent video but he doesn’t mention torque specs and I can’t find that info anywhere online. Thanks :)

Thanks for the video. Was trying to find the power steering fluid reservoir and your video helped a lot. Ended up being below the AC so it’s almost impossible to check. Still though, without your video I don’t know if I ever would have found it

Just in case i missed your answer. On drivers side that is reverse thread. Once outer lug nut is removed, will the inner stud that 21mm socket is used on be reverse thread as well. Thanks

are these tire rods enough to make this truck shake like crazy when they go bad? almost feels like the damn tire is about to go flying

Do you know how much an engine overhaul cost on a 2016 NQR 5.2L 4 cylinder diesel engine ? And who is the best to do the job ?

Glad I found this !!! I just used a 50 ton gear puller on my inner duals and it's jaws ripped small pieces out of the wheel holes! I said "C'mon Man! Something has to be holding this thing on!" I get it - you unscrew the WHEEL STUDS !!! (and there are smaller fixed studs inside those)

If your truck cuts off when you put it in gear, what do you do?

Need your help

Do you have a video off changing the shoes

Thanks for the video, what do you torque the 8x nuts to that hold the rear side shafts in?

Hey Doc, you know if the wheel bearing info you give in this video is the same for an 09?

Thnakew so much

Hey man I love your vids! I learned how to do brakes and adjust the parking and rears because of you. I just recently changed the front calipers on a 2016 and I am unsure of the bleeding procedure. I have the IDSS software but I am not sure if I need the truck running or not. I read a lot of different info on the web. How do you bleed brakes on the npr?

THANK YOU FOR THE VIDEO!!

Wow these look like the old school hotel HVAC unit filters too!😂

What causes the control to jam up? Mine is not knob is not broken but will not go to defrost.

Thnx

Hry NPR Doctor when you can can you perform a power steering flush on a crew cab npr hd 2015-2020. Thanks man have a good one.

I find that jacking the axel up an inch or so to take the weight off the wheel allows a more uniform flow of grease into the bottom king pin fitting and around the bottom thrust washers.

Thanks for the good vids. What's torque spec for the axle flange bolts?