วีดีโอ

Too expensive but perfect

What’s the head bolt torque?

Thank you for the vid, we didn't have black/white cable in our house but thankfully you told us which was electrical/neutral cable 👍

Getting ready to attempt this method on a storm door

Finally someone that shows what wire goe to what wire 😊 thank ur sir ur amazing plz do a video on how to remove and install a ceiling fan plz

Tools Tested made a video about how inacurrate this thing is. Good luck!

Thanks for this video! I got a 3ph for a great deal but was unable to get power. Have been trying to sell for months but unsuccessful. This was the confidence boost I needed! 🙏

was this a Kubota engine and what model

Is this specific to just Festool or will Cubitron mesh have issues with most hook and loop sanders?

do you have a set of the new v2 panels? how close do they look to factory? looking for replacements for my '90 si. thanks.

👏 great job

how can you remove the light without damaging the ceiling if the springs are holding it?

Did you have an overheating issue along with the white smoke

No links?

Looks pretty well useless for anything but open access hardware. You wouldn't even be able to fit that thing in to do bearings LOL

Thanks

Gosh! That's easy. Thank you sooo much!

Can somebody tell me the name of that first (electric) tool he used to sand down the interior?

should not have let it happen in the first place, leaving a piece of paper under the pipes for a while to see if they leak helps

Be sure no bare wire sticks out of the plugs and be sure the wires are very firmly attached to the connectors!..

It would be a handy tool If the torque was accurate torking on that tool is Sh@#t For a tool that cost almost $1,000 dollars You will better buy a snap on digital torque

Shits not accurate, it's been tested. any snap on or matco click type would be cheaper and actually accurate

That torque wrench worth more than the car 😂😂

Thank you. This was very helpful and easier than I thought.

Quick question. I used a plastic box and conduit. What do I do with the ground wire?

I get a wobble when i added the protection pad and 3m xtract. Do you also get this?

Thanks mate!! Did it in two secs!!

Great video. Do you even need to lift and take wheel off or could you do without it? Just wondering since I have no place to safely lift my truck and gonna start this today

I am changing the cylinder head on a Boncat 773. Although I ordered the cylinder head for the V2003T, it arrived different from the original. After checking carefully, this one is for the Kubota V2003-DI, direct injection. Would it be possible to put this cylinder head in place of the previous one?

Hello, thank you very much for sharing your knowledge, congratulations Sir, very well explained.

Are there products that would re-dye the cover?

Would be nice to know the torque specs

Thanks man, finally a video that shows how to do it, and nothing else.

How do you set the torque on adapter

Thanks for this video. It really helps me with decision is it worth to buy these quarter panels. I will probably try to fight with civic iv quarter panel.

Thanks from the crx community

Camera man didn't take full advantage of the opportunity to film the 'mog. Boo

Is too expensive

take my money

Awesome job 😊

what half shaft is this?

I got mine to turn back on, but now it won’t turn off.

If you use spring clips on the external edges you will get an even tighter joint

How many times have you found your architraves glued firmly to the floor?

Thanks for the information. My belt had been complaining severely and finally failed tonight. Made it to the parts store on the battery and then home and with your videos help. Done and done. Thanks again.

Till you find out how in accurate it is

Is there any problem for vechile

I am about to install the same panels in my basement. My house is from 1972 and I just removed the previous vinyl floor to find a damp concrete slab. Since there were vinyl planks on the concrete, after removing the vinyl floor it also started to smell of mold. I am now in the process to clean up the concrete but am wondering if I should put a rubber membrane. I found products like Blue Seal - The ultimate waterproof rubber membrane. Would you consider adding that under those panels?

Hello, Any update? Did they fixed those quarter panels?

Hello, I know that this video is old but I have few questions about these quarter panels. Have you got any photos or video how does these quarter panels looks like on a car? Did they look like the original ones (I mean shape of wheel arch)? It is hard to evaluate from this video and also pictures from the wolf steel store. I know that many people use quarter panels from civic IV gen to crx but they quite different. Those for crx have different shape from those from civic? Quarter panels from civic are cheap compare to those, but if these ones to crx have shape of arch as the original if think they are worth money. thanks