วีดีโอ

Have a 700 wire is loose or off the electric start doesnt charge . Dont need the electric start as it is running one pull everytime change plug every year

Thanks to you video I’m done with my mower 🎉 bravo!!!

Your videos aren’t good at all…but we can hear you very clearly.

I couldn’t see nothing…

Rebuild is a good experience. However the aftermarket clone can be an acceptable alternative. A toss up. 🎉

Just what I was looking for… replacing the piece of the shroud and bracket that controls the mulch/bag action.. parts are crazy expensive… about $80 for the required parts..excellent video!!

i did exactly what you did. i have that same generator and it still won’t start.

Steve's Small Engine TH-cam will give you the best option to cure the problem, worked for me!

Kind of a pointless video ..no before and after results .

Thanks for the great video series. Just completed my transmission replacement using this series and it was spot on, the order is important and you were very detailed.

Very helpful video. I just went out and cleaned up my pinions and keys. Wheels now work great. Although, maybe it's just nomenclature, but my pinion flats face the front of the mower, not the back, which is what I think I heard.

Thanks for the education I own one

Thanks. Series 11, is that most old tecumseh engines? Mine looks exactly like the one you rebuild rebuild

could have done this without the damn back ground noise of someone mowing? WTF, poor planning. FUSA

For those who had a rusty pin on the mulch selector rod and can’t get it to budge, you can cut a slit with your knife in the plastic on one end and slip the cover over it.

I did this without removing any of these parts. None. Intelligence and fine motor skills. If you have this problem, look closely at it for a while. You'll figure it out.

For the love of Pete, the wind chimes are giving me seizers. Cutting the engine two seconds after starting it tells me this failed. Thanks for the effort.

This was super helpful, fixed my self propelled mower. Thanks

Would be nice to have a hint of how to get that transmission spring back on--what a pita….

Makes no sense. All you did was disassemble and reassemble the rear wheel mechanisms without pointing to any reason why the wheels won’t go backwards. No cleaning, no lubing. 🤪

I'm looking for a replacement chain for this exact chainsaw but I'm confused about what will work. Anyone help?

The Dog did not attack the man. It nipped at his pants because he turned away from it. Just an overly exited dog looking for attention. I understand that he turned away to shield the dog he picked up but that's why it happened. Never turn away from a barking dog if you can help it.

1:22 The 12mm bolt. Looking at mine, it didn't appear to be 12mm. 8mm? No, the socket just spins on it. Turns out whoever tried to fix this mower in the past broke the head of the 12mm bolt off. I think I should be able to use a punch and tap it out, but if things are rusty like they are on this HRX217 I'm repairing, it can be an issue. I'm glad I waited to order parts, as I'll need new bolt and retainer. It looks as though I may need to replace the hydrostatic transmission also--one of the keyways where the key and spring sit in the axle is wallowed out, and one of the axle spacers was holding the key in place, and cocked sideways. And beyond that, I don't even know if it works. Going to test it but I'm not hopeful.

My hero! 🤩 My belt broke on my little Sears Weedeater after years of use and now I can put on the new one@ I'll take the opportunity to clean up and see iv my blades need sharpening. They're fairly new but still. Thank you very much! Isabelle 👋🇨🇦

t

Thank you. I do have two questions: 1st: What if idle is low (lever on low), and mover dies? There must be an additional setting for minimum speed/idle? 2nd: Where did you find the book to download with all the instructions? I can't find anything related to shop/service manual, only owners manual...

Es normal que gire el cabezal sin acelerar?, ya cambie todo el motor y el carburador por unos nuevos pero sigue igual 😑, por más que trato de calibrar las RPM pero no se puede, si bajo demasiado las rpm en baja se apaga por completo la máquina, y aunque mueva el tornillo del relenti tampoco nada, no se si sea normal eso, no deberia

For the love of god please muffle those wind chimes!

😎✌

where is the air filter sir?!?! i can't keep mine on longer than 15 seconds. ugh,. frustrating

Weirdly enough, I just got one of these given to me. I was surprised to find the deck was plastic.

Thanks for the video! Carb cleaner is mostly acetone. Maybe you could save some $ if you just bay a gal of acetone. Don't get it on the mower deck's paint!

Thank you

Remove the outer snap ring, drive gear, woodruff key and spring store these parts in plastic bag. Install wheel push and pull mower manually with ease. My yard is relatively flat and not worth the aggravating wheel lock up pulling mower rearward. I could use the exercise. 😮

Thank you for this! A lot if videos say to bend the arm. That didn't seem right to me. 🇺🇸

You sir, are a blessing! Your video was a great tutorial on how to help me get this done.

pia to even think of taking this up!

Thanks for the video i did the same maintenance and boom. Fired right up!

I have a 1999 weedeater tractor with a 13 hp tecumseh

At the 8:31 mark i cannot get that piece off the shaft. Very seized and I applied some wd40 to hopefully get it off. Really want to save this lawnmower

Time wise. Took 4 beers. Thanks Honda. Should of been a 1 beer job...

Won’t the opposite side wheel gear slot face forward?

Where are you based out of .

I’ll never buy another cub cadet. Can’t go two mowing seasons without a problem

What is the part number for the spindle you replaced on the weed eater 38 inch mower deck I HAVE THE SAME EXCAT MOWER DECK I NEED TO REPLACE BOTH SPINDLES THANKS LACY

You need a large 2 jaw puller. Your not getting it off without the puller.

Those drive belts are bitch.

The chimes!! Seriously!

There is a dimple on the gears. They face to the right viewed from behind.

The silver cap under the primer bulb chamber, is what I'm missing. What is it called?