วีดีโอ

Where do you bleed the system?

In the owners manual for the front struts it says use the oe bump rubber after the metal collar that slides over the snap ring, I noticed you didn’t in the video, did you have issues with that??

Love how they immediately started to sweat inside when installed 🤣🤣 those depo headlights are so terrible when it comes to stay dry inside

Apply dielectric grease to electrical connector pins.

Saludos hermano, podrias darme la información de donde puedo conseguir ese parachoque nismo yvque marca es

Nice ride love my z.

What wires you used to connect the Z logo

what dash kit did you use

Hi are you able to send me the specific link to the rust kit bundle?

Can you drive it with the roof lining out? Embarking on this mission but need to use the wagon in between removal & refit.

Steering wheel command connection?

Thanks. Can I ask how you knew how tight to set the tensioner?

Ues a standard screwdriver

how many miles that car was when you did the timing belt service?

'So I'll try and explain what I'm going to say without saying Alexa.. URGHH' 😂😂 Nice video, I'm looking at the updated version of this unit. What harness/wiring will I have to use for my Z or is that included would you know?

Should have bought the custom led light genuine 350z badge indicators.

How do you get the back seat out? Not the base, that's easy. I mean the cold down back?? Cheers

Hi do you have a link to where you got the trim seals? Been trying to find a universal seal that will fit since the OEM seals are only sold as one piece with the trim panel from the dealer... thank you!

Awh the area of rust at the rear sills. I had this exact thing happen on my 350z. They all rust there. Youre like "thats not too bad" 1 wire wheel later...."its pretty bad". I ended up sending mine away to be welded. And pretty much replaced that whole little section on each side.😅

Well done good job pall, only one thing, always change water pump and idler pulleys when doing a timing belt is strongly advise.

Can I change the slave cylinder tube with out removing gearbox ?

Mine went at 90k, luckily was parked up but clutch to the floor, you can actually bump start it into 1st or 2nd gear, I drove it the garage at high revs.

Only on that type though

didn’t the lino get whacked by a county fan or somet?

Well done Crewe love City of Derby xx NB. Remember to clear the away end of used needles.

Luv it getting my done too thanks for the video 👍🏽

Good video but needs to show use new crank bolt and bolt tightening sequence as its torque and angle

Thanks for the video, i have a question, you said that you drilled a 55mm hole right?

Sadly fitted all mine, wired the reverse camera goes to test it and no power on the unit getting a multi meter to check the wires but no clue what else to try. I have a 2008 freelander 2 I’ve used the red iso wiring for the back of the unit I don’t have the fibreoptics in mine as I only had the cubby hole before but cheers for the video

How do you adjust these mine shine too low to the ground can't ever see or Dodge anything in the road

Sick I may get these lights for mine 🔥

Cheers a very helpful video as i have a sunroof leak probably the drain ports blocked (easy fix) OR broken snapped off or drain tubes detatched hope not, will need the headliner removed to do repair on the broken parts. If anyone has done this repair before please let me know

Good video, i need to replace the glass, any tips? I cant find a video that goes beyond the regulator

looks amazing, although its not a tutorial its great to see the process of how you did it

Great job mate. Cars looking well 😊

Love it!❤

Nice custom work on the indicators!

where did you buy the side skirts?

Good stuff! I can't quite figure out why the flywheel needs to be locked twice, with the pin and also one in the flywheel teeth? Maybe tightening the crank pully can bend the flywheel pin alone?

Jesse here can you share links n’ how to order, own a Lr2 2010, thankfully from San Francisco CA. 😊

Can you get to the key receiver without taking the headliner out? TIA

hey ! I'm about to fit this bumper on my 350z, with those lights. But can you tell where you connect them ? looks awesome on yours !

Wonder why here in the U.S we never get cool option like these..

Hi just stumbled upon your site very interested,it seems were on version 12 now what is the current equivalent spec to what you have used and did it come with a fibre optic loop if indeed needed,thanks in advance

There's a great opportunity for me to f**k this up completely.

Hi Av lost my micro Nav sad card any help in getting a new one Carnt find one anywere

you didnt do water pump