- 36
- 176 161
karldingbat
เข้าร่วมเมื่อ 9 ก.ค. 2012
On this channel i want to help people to get things that are broken, or simply hard to get to work.
I will give all the knowledge i have and will gain in trying to sort stuff out. But it would be a huge help if viewers could subscribe to my channel. It would help me and you'll get notified when i upload videos.
Thanks
Karl
I will give all the knowledge i have and will gain in trying to sort stuff out. But it would be a huge help if viewers could subscribe to my channel. It would help me and you'll get notified when i upload videos.
Thanks
Karl
from living in a nice big house, to living in a van!
due to some very unfortunate circumstances i am now living in an ex ambulance. we had a bereavement of a family member at a very young age and it affected me and my wife beyond repair, so we decided to go out seperate ways and im here now.
there will be many more videos from me hopefully about fitting this thing out and anything else of interest, so stay tuned!......
well my luck seems to still continue on its downward spiral, as the engine in the ambo has just spun a big end bearing on the crank and im now faced with a £5000 bill at the minimum 😔👎😒😒
there will be many more videos from me hopefully about fitting this thing out and anything else of interest, so stay tuned!......
well my luck seems to still continue on its downward spiral, as the engine in the ambo has just spun a big end bearing on the crank and im now faced with a £5000 bill at the minimum 😔👎😒😒
มุมมอง: 199
วีดีโอ
an absolute must have if you own an EBERSPACHER of any sort !!
มุมมอง 9K3 ปีที่แล้ว
if you own an eberspacher airtronic, water heater, timer, or anything eberspacher there is a website that IS AN ABSOLUTE MUST HAVE, it gives all the information you will ever need. www.letonkinoisvarnish.co.uk/models_a1_current.html
Eberspacher airtronic D2-D4 yellow signal turn on wire.
มุมมอง 18K3 ปีที่แล้ว
an update on this scania heater, it works, I've managed to get the thing to work, i had forgotten to reconnect the intake air temp sensor once it was back on it started straight away. the fan motor that i thought would need to be changed does not need changing as both 24 volt and 12 volt use the same motor, the voltage for the fan motor is controlled by the ECU itself.
Chinese diesel heater, fitting a remote control wire.
มุมมอง 4.8K3 ปีที่แล้ว
how to solder wires to a cheap Chinese diesel heater to allow it to be turned on with a gsm switch. here is the web address for the gsm switches. www.gsm-uk.net/
update on the webasto thermotop water heater.
มุมมอง 1.1K3 ปีที่แล้ว
update on the webasto thermotop water heater.
short circuit 24 18650 battery explosion, 100 volts for giggles
มุมมอง 5043 ปีที่แล้ว
please do not try this, it is DANGEROUS and could quite possibly cause you to not have a good day.
Ali express 1800watt boost converter setting volts and amps
มุมมอง 20K3 ปีที่แล้ว
Ali express 1800watt boost converter setting volts and amps
Ali express 1800 watt buck boost converter. any good?
มุมมอง 4.4K3 ปีที่แล้ว
just made a real quick look vid of this buck boost converter, sorry its upside down, don't quite know what happened ? i will do a more in-depth review tomorrow and promise it will be the right way up!
fitting air suspension on a hyundai i800
มุมมอง 9523 ปีที่แล้ว
very quick video of the air suspension fittup on my hyundai i800/ grand starex /h1/iload van
cheap tube bender, not all its cracked up to be!
มุมมอง 2703 ปีที่แล้ว
cheap tube bender, not all its cracked up to be!
turn any Chinese/webasto heater on or off by text.
มุมมอง 4.5K3 ปีที่แล้ว
turn any Chinese/webasto heater on or off by text.
saving a small fortune on Eberspacher airtronic repairs !
มุมมอง 14K4 ปีที่แล้ว
saving a small fortune on Eberspacher airtronic repairs !
running an Eberspacher airtronic D2 on a cheap Chinese ECU and controller !
มุมมอง 14K4 ปีที่แล้ว
running an Eberspacher airtronic D2 on a cheap Chinese ECU and controller !
EBERSPACHER D2 AIRTRONIC WHATS IN THE CASE !
มุมมอง 1.4K4 ปีที่แล้ว
EBERSPACHER D2 AIRTRONIC WHATS IN THE CASE !
7 day mini timer how to wire up and use
มุมมอง 4584 ปีที่แล้ว
7 day mini timer how to wire up and use
pure sine wave 24- 240 volt inverter first test
มุมมอง 504 ปีที่แล้ว
pure sine wave 24- 240 volt inverter first test
Webasto thermo top c/z canbus removal board.
มุมมอง 25K4 ปีที่แล้ว
Webasto thermo top c/z canbus removal board.
mini lathe cutting display from vernier caliper
มุมมอง 2324 ปีที่แล้ว
mini lathe cutting display from vernier caliper
just wanted to see if this actually works ?
มุมมอง 524 ปีที่แล้ว
just wanted to see if this actually works ?
Webasto thermo top c start signal pin debate !
มุมมอง 6K4 ปีที่แล้ว
Webasto thermo top c start signal pin debate !
Webasto thermotop c garage heater, sorted
มุมมอง 1.8K5 ปีที่แล้ว
Webasto thermotop c garage heater, sorted
Cheers for all tips I'm going attemp fitting a 4 channel diese RC wifi smart switch dc so i can control on/of up and down
Hi Karl What did you set the settings for the fan speed etc?
Hey Karl, hows ot going? Do you do mobile service on heaters? I got a vw Tucana Bluebird and i got a few electric issues the heater being one of them thst i could do with some of your expertise. Dm me if this is a work that you are able to do. Thanks for the videos
Sorry for delay in replying. I can do depending on where you are ?
I hope you have found your feet and soon you can return to make videos
hi. How can I get ecu and contoller in Iran?Which brand are these chinese ecu and controller?
Loooooool..! Brilliant...👍
Outstanding..!
Nice video, mate. Im going to give this a try. My chinese heater is making great heat , but the fan is making a strange noise. I was given an airtronic D4 , with a broken control unit , so now im going to swap out the unit and swap over the motherboard, and hopefully it will work. Its minus 16 here in Canada lol and gunna get colder.
Hi, I have my BMWX5 and there is thermo top z on it I was thinking on putting this on my boat so heat it but there is a little problem that you need a controller and according my understanding the C version works on any simple controller, you can even start it by crossing cables but according my understanding the Z version needs a signal from controller. It is quite complex. My question is am I right on all of this? Also could I just replace a board from the one and making it a C one in order to buy cheaper controller?… I don’t know if that makes sense.
I dont work with bmw versions of these heaters as they work on canbus systems, i just swap out the circuit boards and use either an aftermarket board or 1 from a Peugeot diesel car.
Thank you very much. I was wondering if I could run this heater by plugging any source of controller or I have to replace the board.
got an d2 on the boat to be honest its a pain in the bum would never have one again using a chinese suitcase one at the moment
thanks
👍
🖐️👍
Can u tell me can u get after market control board for the top v night heater the one I have cuts out after an hour
I've done the same as you but the exhaust is now coming out of the combustion inlet any ideas please
Yep, motor is spinning wrong way change wires around!
@karldingbat just had another look at your video and seen the brown wire is on the out side I though it was the positive thank you very much for your reply top man
Chinese wiring is crap! Ive noticed even the red wires can be negative they just dont give a shit and put anything in.
Can anyone tell me if the car ones are programmed to switch off after 15 minutes running ? Someone has fitted a car one in my narrow boat prior to me owning it and it cuts off almost exactly after running fine .
No, they are not designed to shut off after a set period of time, any time limitation is built into the timer/controller but these are the 701 timers with the blue writing on.
That's really neat. Then you can use the abundant cheap used VW Webasto units for your garage or any project.
Will this work if I had a 24v one. So it will turn it into a 12v
Thanks karl,get the feeling that the uk is heated by airtronics with kerosene 😅 Here in finland mainly in cars(electric) trucks etc.
More and more people are using aitronic and webasto heaters as the price of electric and gas prices keep getting higher and higher, its getting to the point now where we cannot afford to stay warm. But the government are looking at banning diesel heaters so we may all die of cold!!!
Can this device handle treadmill dc motor of 18amp and 95vdc
I'm using it for that very purpose.
I wonder if you can help me, as I've bought a Chinese motherboard to fit to my Eberspacher D2, but it has two three pin connectors at one end and one four pin connector at the other end of the board. I have attached the four pin one to a new Chinese glow plug that already had a four pin plug on it, but I'm not sure which connector to fit the temp sensor and fan to, as they both look the same and the temp sensor will fit on either connection point on the board. I'm now waiting for a wiring loom to arrive to plug the mother board and time into? Any help will be appreciated. Thanks, Pat
it's rated for 40amp input, can it do so that or near those amps, on 40V-50V input?
Its 1800 watt total input plus output, you wont get near 40 amps at 40-50 volt in you need to calculate the absolute max of 1800 watts for the entire unit, in plus out combined = no more than 1800 watts
@@karldingbat cool lets forget about input volts. Can it take 35a or 40a current input? Ever tested?. If not, are you able to confirm.. it would save a day.
It no doubt could take this input current if the voltage was correct but as a boost converter the output voltage would be higher up to around 110volts with roughly 3amps it all depends on what its to be used for
@@karldingbat awesome thanks for the reply dear
What a stupid waste of time and money, on something complex and unreliable.
Why be douce bag pal, your pathetic comments no doubt reflect your pathetic life 👎
Again One of those Useless videos
Nobody asked you to watch, just jog along buddy 👏
I need to help me How to power 24 volt , 3.8kw webasto thermo pro 50 eco with ADR 4:
First of all you need 24 volts, i dont know what power supply youve got, but if 12 volt you need a boost converter that can supply at least 10 amps
I just love your accent mate
Just wondering what pump you used. I have a d2, put a cd ecu and controller,
I use a d2 pump, rated at 1 to 4kw
Just subscribed after watching this great video and will be watching the rest of your diesel heater videos great helpful content easy to understand cheers 👍
Şema plss
?????
To increase amps clockwise or counter ?
How do u set the amps clockwise up or down?
Had a D2 sitting under the bench since the ECU failed in 2013 and I bought a D4 new for £1400. to keep my workshop warm, anyhow after seeing your vid I bought a Chinese ECU and controller with remote for £20. and yesterday (January 2024) pulled the old heater out and installed the Chinese bits it fired straight up so cheers mate.
Brilliant! I was just thinking the same. I've got an old D1 but it also needs the metal exhaust and air intake part as it's rotten.
@waterboy8999 i dont think it'll work on the d1 as they use a different style glow plug, not ceramic its a coil and takes a lot more power.
@@karldingbat OK thanks, looking at the cost of a new rice burner there's really no point in messing with it.
The d1s were ok, but they used an awful lot of power and tended to stop working quite quickly, i dont bother with them to much. Hard to repair.
@@karldingbat this one definitely works but there's no starter relay in it and the exhaust port is very corroded. If you want it for messing around with I'll send it to you.
Hello my friend just subscribed and liked. Okay so my heater has just stopped working and I was wondering if you would be able to have a look at it and try to fix it for me or can you please help me in any way I'm based in Slough near Windsor kind regards Dean 🙏
You say, stopped working, what happened what symptoms does it have, or is it totally dead ?
Had this idea a while ago - glad to see that someone already realised it!
Can you swap out the programmier for a 7 day timer clock. The current one means i can only select one program at a time, which is a pain.
I used a 7 day cheap Chinese 12 volt timer on mine i had multiple days and times set up on it, i just used the timer to switch the signal wire on or off
Hi Karl, I have bought your recommended ecu and control panel and I am happy about the connections to ecu inside heater as per video, but I have not got the chinese main loom. Is there a wiring diagram to use the eberspacher loom onto the ecu and controller and fule pump.
Die Steuergeräte gibt's im ebay komplett mit Anschluss Kabelbaum aber auch einzeln 😊
I have bought the chinese ecu and controller but I have the Eberspacher loom. Is there a wiring diagram I am happy with the ecu wiring you showed in video but what about fuel pump and controller when using eberspacher loom.
Hi mate , how did you doagnose the faulty ecu ?... Ive got this noght heater in my wagon , everything seems to work , theres no fault codes however , the heater just blows out cold air. Ive chanfed the glow plug and the metal screen but still ,just cold air... Read up that i need to reset the codes for it start a new cycle but im ubsire how to do this eother.
To reset the heater, you need to completely disconnect any power to it and leave for about 10 minutes i normally leave disconnected for 30 mins then reconnect and try to restart, if it starts turning and just blows cold air for about 5 mins, either the ecu is faulty, or battery power is to low.
Thanks Karl I was about to chuck my eberspacher D2 in the bin as the ecu unit was naff so I followed your video and by god it works its been running for 2 hrs with no problems. I do feel it is running a bit hot. Bloody magic. Thanks again Kev 👍
You can tune the fuel pump in the menu on the controller to match the burn, its under the hz setting
@@karldingbat I've got 3 Oriental knock-offs and none of them shut down when the stat tells them it's warm enough - you can turn them al the way down but they still pump fuel unless you switch them off. My D4 goes on standby 'till the temp drops then kicks in and winds up the temp. again. Gave up on the Commie rubbish 'cause the electronics are so cheap n nasty, just throwing mystery fault codes and one replacement motor just stopped for I don't know what but the pump kept banging fuel into the burn chamber. Just lucky I was there to pull the power!
@@dancarter482 ye, there shite, what you want me do, give you a refund ?
Great vid. I wonder if it would work with a D5?
D5 ? Im not aware of this model
Hello. Hope ur doing ok m8.
Great vid man👍 Just bought a eber with broken motherboard. I will try this👍
Perfect exactly the medicine i was looking for, have a lovely D4 in me boat that needs a bit of lovin, very little use on it professionally fitted id say with no expense, be ashame to fuck it out, gonna give this a go,, nice one dude...
Greeting! Very educational videos!!! Well done Professor! Which converter would you recommend to make a power supply with DC input and output~ 4-6V and ~8-12A adjustable ! That it can work without interruption and overheating for a long time!
bro if you wan a challenge try outting 4 in parallel, so are all putting out equal power. i pulled it off with the 1200 one, then 3 of them died
Bit of an expensive exercise, bit like parallel fuses once 1 goes, the rest follow
can this handle an input voltage of more than 60 vdc like 63?
Not sure, never gone above 48 but shouldn't think 63 would be a problem but dont take my word for it!!
the D4 has extra wires will it work?
This was just before it spun its mains and rod bearings😮
If I have a Webasto controlled via remote will it still work if I change the ECU to the one from NorX? Thanks for the informative video
Yes i think it should work just fine, its only eberspacher that are a bit of a pain!
Afternoon love the vids and found myself with a problematic d2, can you change the controller without changing the ECU?
Yes, the controller on the d2 is a plug and play unit separately from the ecu inside the heater, unless some1 has wired it directly to the ecu which isnt a good idea
I done some digging on mine today and the 6 cable loom that goes into the back of the controller goes straight down through to under the van where the d2 is, not found any more of the wiring, great I will try pick up a cheap Chinese controller and give it a go
@@MrGingergod123 it may not be possible to use a Chinese controller with the standard eberspacher ecu as the Chinese controllers use a 5 volt canbus type of signal where as the eberspacher uses a 12 volt signal, if your ecu on your heater is good it would be better to use a controller for the d2 instead of causing possible damage to your very expensive d2 ecu.
@karldingbat ah okay I'm not too sure if ecu is good or bad yet, was hoping for a cheap fix as my 801 controller display is messed up
Ok, this fix was to replace both the ecu and controller if the ecu went bad as they are megga expensive, if your changing the ecu for chinese you do need the controller as well, as the chinese and eberspacher are not compatible with each other, hope this helps.