วีดีโอ

@2:01 You never use water for a gasoline fire.

I have a problem with my accord v6, the thing is that the check engine light is off, I don't know what to do 😢😢😢 help me!!!

Oh fasho !

How do you get oil on distributor?

Just did this to mine ! You're a legend!!!! Thanks mate

Good job

Thank you😅

I got a 1999 honda accord coupe v6 i was drivin mines yesterday an turn off while i was driving tryn figure out what it could be i put a new battery in it

I pulled off my cap today and noticed oil in the cap too. Cranks but doesn’t start anymore. Going to change the distributor.

Great video dude

Sir did you drain the gas before you cut the body sheet.

So this fix the immo?

your a genius , thankyou so much

Very well done. Thanks for the tip. Who woulda thunk ? Step by step you figured it out. Very cool.

Ty for the vid bud

The thing you refer to as a button it actually called the rotor.

Hey dude that was great man I really appreciate you helped me out great man love you brother thank you

Work like a charm on my 03 Town and country, thank you very much

Really good video,for sure you help to many people,thanks God but my 98 crank but no start,no spark the main relay it's ok and cero RPM.God bless you.

My 95 accord is hesitating to accelerate at 2500 rpms and hearing pops under me until I press down the gas more and suddenly it accelerates like if the vtec kicks in, can my fuel pump be going bad?

You heloed me my friend good looking out im back rolling.. appreiciate ..

Good man

My cars shutting off while driving but comes back on I haven't had time to fix everything so thanks for your time.

My understanding is that the service department is where most dealerships make their money. I'd love to see a new car maker make one danged car extremely well and make money from selling many . Like we do with Honda Accords and mainly Civics, we could rice that car in a zillion ways. And, make it easy for the consumer to fix and maintain him/her self.

Idles good. What about the engine check light? It's still ON....

I cant find the green/orange cable, becuz the computer is located in front of the driver wheel.

Would it work for a 2006?

Yu run the ground from pin 85, or 86?

I’m having the same idle issue I’m about to do this method

What the other fella said here: Disconnect the sway bar link on the side you’re working on to prevent suspension binding. This will facilitate more downward travel of the control arm to ease the install and removal of the strut. If it’s still fighting you, you can loosen the control arm bolts a couple turns, but they have to be torqued to spec with the suspension loaded at the end. Don’t overextend the upper ball joints or you’ll be replacing the whole upper arms. 😎 Hope this helps some folks! Solid and helpful video, though! 🍺 ✌️

Mine cranks but wouldnt start. No codes.. The green key light on dash was flashing ... thats the security system indicator. After disconnecting the battery for 20mins it reset and car fired right up.! Only lasted a few days, went to start car...same thing. Repeat the battery process, starts again. Tried reprogramming the key..didn't help. I'm told that I probably need the transponder ring, which is around the ignition cylinder ( where the key goes in) as it is not consistently reading the key chip and therfore stops the fuel pump from sending fuel? Befor trying this, I'm going to pop the distributor and have a look. Thanks for the suggestion.

Thanks brother my 98 been doing this for years

Good man. You are a scholar and a gentleman

How did you get the brown tube into the clear tubing? It's so tight up in there.

Igniter that's all it was on my 98 acura 3.0

Nice good to know

ThNks

So it’s the iacv and not the map sensor or tps ?

Is the map sensor on these the same between 98 -02

Yea man you never know who will see this and find a historic gold mine. I should do videos just never learned how exactly.

My 1999 accord will crank but not start. It also will not allow me to shift out of park. Put screw driver in release and shifted into neutral. Will not start in neutral. Break lights are working.

How did you cut It?

About to do the same thing tomorrow to my Honda ...fuel pump went out last week👍🏾👍🏾🤔

Thank you for making this video, My brother is having a hard time replacing the fuel pump, do you have any tips on how to replace.

What kind of blade did you use on your dremel ? Where can I get a blade ?

Good video, I same car my distributor n roter got stuck n metal over heated the metal is bonded, any advice, in taking out taking to machine shop , I thought I had wrong roter but auto zone had same one that cam from honda. Good luck on your project.

Thank you bro much love ❤️

Thanks for posting this video thisbis the same thing that is happening to me with my 98 honda accord ex

Just did this on a 95 accord! Thanks for the guide. I used a drill metal cutter to make a hole. Then used some hand held heavy duty metal cutters from Harbor freight to avoid sparks as much as possible.

What the mileage on your accord when the FP went out ?