วีดีโอ

You save a lot of time and money. Thank you.

Great video, brother, you just save me a whole Lotta aggravation. my entire stove out of the cradle to see if I can get under it. I will order that part now and see if that’s the issue. Thanks again.

Very clever… wish I saw this before our door fell and damaged my floor~

Hey so how do you turn on your oven

2024! Wished I’d found this 3 years ago. Been living with broken / open / hanging down lid for YEARS, thinking there Must Be A Way, or the day I can afford a new one. Well I have an older home and suspect its a heavier metal. Found the mags on Amazon with a review from a guy who also had watched this hack- what are the odds! - he said the mags were the size recommended here. I bought a set of 4 for about 7.00. I placed all four spaced along the edge and There It Was! Closed! I tied something to it so i can pull it open. I am so grateful, but also shocked that for once a simple hack worked - for Me!

Great solution

This is the second Moen product in my house that no normal person could ever figure out how to repair without great effort, and which requires a special Moen tool. I will never, ever buy a Moen product.

Thank you for this video. Magnets who knew. Great idea. Thank you

Thanks. I have been using gorilla tape. Getting these now!!!!!

I have replaced 3 of these valves because the gear teeth wear out or the valve allows water to collect in the bottom and rust. Im over the expense name brands to get lousy service life. I am going to give the cheap knock off brand a try.

how to turn off!!!

The tool for mown 1224 bought in Amazon didn’t work but your method works a perfectly. Thanks!

Much appreciated for the exact idea that I had wasn’t sure what to use, part of me not change the filter often enough was because of that problem, thx again

Thank you!!!

Stick your hand in the drip. If it’s hot then you know it’s the hot. Whichever one failed is the only water going through it when it’s off

The pry bar trick is money!

Perfect. Mine was even the exact same cartridge.

Thank you for sharing your tips

Can you turn the valve manually like the Jandy valve?

I need HELP to identify the Tool used to remove the retaining rim from inside wall. I am unable to pull cartridge :(((

One of the best diy videos I have watched!

Just an FYI.....Moen has a lifetime warranty. I just recently called their customer service, told them I have a slow drip, gave them my model number and address and bam a week later 2 cartridges arrived at my door at no cost to me.

Thank you sooooo much!! Almost broke my neck trying to shut a high ceiling grill!

Brilliant idea!

I am replacing my mother-in-law cartridge and it would just spin spin spin thank you for helping me correct that I was in panic mode❤😅

Thank you!

I’m curious how you removed that small piece from the very top of the handle. Is a screw in there?

Awesome diy video . Thanks for sharing 👍

Thank you for this excellent video! So often TH-cam videos don't show the sticking points in a job and don't offer the tricks to overcome them. You shoe them all. Seeing someone make a mistake or have difficulty with something and solve them is golden. The only other problem I had, and you didn't, was getting the faucet handle trim to unscrew because of some lime deposits. I had to loosen the faucet nut below the countertop a little bit to release the trim and retighten the nut in order to avoid damaging the trim. Great video!

This was super helpful! Thanks!

No need to power off panel. Put in test mode. Replace switches.

After reading your comment section, im going to return to keep watering the air layers lol

Wild moss and the root ball cover is exactly the method i used and i have no idea too 😂 im so excited to see the results in a couple of months ☺

If the faucet is leaking, the quarter turns may need to be replaced. you can check this by turning off water to the faucet, if drip continues then quarter turns are bad

I have the old model of GE profile gas stove with downdraft cooktop. It appears my gas stove head is one piece and I cannot remove the cap like you do. There are two side screws to remove the whole base inside of the cabinet. I cleared each hole with alcohols rub and needle and it still doesn’t work. Is there an easier way to fix the stove heads?

Thank you for the tip on pulling out the old cartridge, I was stuck at that point...

Thank you. Great video

👍👍👍👍👍 Thank you!

Dude- worst video ever. Sorry. But you need to audible your actions and cut the length down. Like watching my wife get her nails done.

Bless you good sir 🙏🏽🙏🏽 I needed this for my grille

i have the Maytag electric stove and now all four of them doesn't light ups..... hope i could resolves the issues soon.

Why does that happened?

where did you acquire the new lighter? How does one know which one to purchase? tx

Thank You❗️

Phenomenal way to remove the cartridge. I am struggling to remove a faulty one. Update: I succeeded in removing the cartridge using the method shown in this video. Before I saw this video I had managed to punch my left eye extremely hard when the needle nose pliers lost grip on the cartridge. Here are the instruments I used: 1. Everbilt 10-24 TPI 3-1/2 in machine screws (gently thread the screw all the way - till you face no resistance) 2. Harbor Freight PITTSBURGH 15 in. Long Reach Locking Pliers 3. Husky screwdriver handle as the the fulcrum

Great video. For anyone out there needed to replace one, I recommend replacing both while you're at it. If you don't, you'll end up doing it sooner or later anyway and you'll have to relearn the procedure all over again.

OOOHHHH SHE SQUIRTS!!!

Thank you so much. This was indeed very helpful.

Superb video

I have two that will spark and two will not. How can I fix it