วีดีโอ

Need to talk mate. Don’t know why or what you’re even doing half the time and the text in the video is inadequate.

Thank you! Do you know where I can find a manual or more information on this trolling motor?

no balance?

What size and type of welding wire did you use? What were the welder settings?

Complimenti per il lavoro.. peccato che quella generazione di motori aveva il cilindro in alluminio consumavano tanto olio! Poi sono arrivati con il cilindro in ghisa ed è diventato duraturo

Could you list the parts number please.

any chance i could buy a kit from you? i have this bought on 2nd hand. hard to find here :(

Good clear simply to understand breakdown, Much respect.

Ой під дубом, під зеленим, гуляв дурний з навіженим. Не той дурний, хто крутився, а той дуний, хто дивився.

Hey , I'm Chris and next you want to break a bolt free next if you have it try PB Blaster for a little more help.

also needs a safety valve let's out excess pressure.

I shovel or spade is the easiest bead breaker I know. Put on bead, jump on it.

I have a chinese 49cc one. Can it take same parts? I dont know what parts to buy or if the amazon one will fit like brake calipers or even just thhe pad. Also, I'm from California. Are these legal here? I cant find any information on the subject

Very impressive.

The torque wrench "click" sound when tightening the bigend bolts was a nice touch. 😂

Nice video, Thanks for sharing. Can you remember roughly how much oil went in?

This production is great! It’s exactly what I needed to replace the carburetor on my 2001 322L! I hope to complete it tomorrow morning, and god willing, it will breath life again.

Thanks I'm going to do that..... my dad just had his done and they charged him $50 some dollars.... plus he had to drag it to the shop and drag it back home again.... I know I'm just a woman but I just fixed my lawn mower today that was sitting too long and had a carburetor all gunked up so I think I can do this

N laviu g z taci b❤❤❤❤❤❤❤

Thank you for the video and the perfect camera angle, about to dig into my Husqvarna 55 and see what's going on. Been a very long time, it's over due for some deep cleaning and maintenance

Saludos

Would be helpful if you actually spoke during your video also or did voice overs afterwards

Very helpful! Thank you!

Looks great, thanks! just picked up one this last weekend to restore!

so..my shock it's doing a weird knock sound when you compress it. It just came back from service... but before the service was already with that knock. It's very weird because you can actually feels something grabbing the travel when the knock happens.....i really don't know what can it be. I read something about the IFP that can be wrong, but I don't know how that would cause a knock on the shock....

Your mom is gonna spank you good for using the kitchen sink to clean parts. I used my mom's 12-quart stock pot to boil the block & other aluminum parts clean.

Thanks for the video! Can you share the motor part number?

It’s a must to have a generator now Just the saving of food will pay for it soon 😊 Try to plan for a outages because 10 days without power is hell Ask Houston Texas folks 😢😢😢

Great video and to the point. I wanted to add casters to a heavy file cabinet I’m using as a tool chest. Thanks

Great video, where did you source the bearings, seals and clips for the gearbox rebuild?

🖖😎

What is the o'ring for ?

After pulling out the destroyed bearing out of the gearbox, I'd be inclined to use zz bearings instead of 2rs. Lots of great work here

I own a similar vid mar I bought when my plant shutdowns. I added casters to one at work, if you do this most will need a step stool for higher drawers.

Rebuilt my rancher 55 and will not start. New carburetor, gasket, air filter, fuel filter, tank vent, ignition coil and plug. Has good fire to plug. What’s next, Help!

I had this same exact engine

Bro made a homemade ring composer good vid

Wd4 in the honer 😂😂 never sen that

FINALLY A WELL ILLUSTRATED VIDEO ON THIS OLD FORK, i'm searching around from a while! Since I refuse to swap this amazing fork this is going to be really helpfull

Did you remove the ring and clean the piston, or did I miss that. I have a homelit blower that looks very similar and has no compression all I see junk around the ring and cause it to be stuck in pistons, I would think this has to be my problem.???

Some people will never understand the feelings of something starting again

Whats the fuel mixture for these?

What was the cost on the rebuild? By the way great video thank you for showing the process 👍

I’d recommend investing into a torque wrench. Cringed at the con rod and head installation.

Thanks for keeping it simple.

Thank You for this no nonse approach to a complete rebuild and repair of this little workhorse.

I am rebuilding one of these atm The flywheel has a woodruff key, like the one in the video. The points cover says "Caution Do not use a steel key. See Instructions" as doe the cover in the video The key that came out looks to be steel. What am I supposed to use? Is there some other kind of key than steel? Thanks to anybody who can shed some light.

You would be better off order a new motor from Grainger

It’s called show & tell!!!!

Need sound