วีดีโอ

I was able to remove the left side without having to cut any zip tie

Incredibly helpful! Best instructions I've found yet.

Thanks man! I'm about to do this job myself. Been over 30 years since I've changed my own motorcycle tires so I needed a refresher... and this will be my first shaft drive job also.

What causes the throttle to “stick” or not “snap back” is, they are pushed forward too tight against the switch housing.

Love the video, excellent tip for rear tire removal.

Cambia mestiere.

Looks like a good video for my 2023 Heritage. Thank you. Don't have to move the mufflers or set screw. Great info.

thanks for the video, i've got the back wheel off but the front axle wont slide out freely :( i've undone the calipers and the little clamp bolt but axle will not bang through?? any help?

Awesome video thank you. I have an XVS1100 but looks pretty similar. My old bike was a XVS650.

I could barely get my front axle out on my stand, maybe the sides are switched.

The dealership said you needed some kind of alignment kit to change the tires hmm not so sure about that now thought it was bs but real question is how do you change out the wheel barrings

I got a 2011 dyna with a weird rear wheel issue. The center line of the tire is not even with the center line of fender. Tire center line is to the right of the fender center, all spacers inplace, it's spoked what could cause this issue

Awsome M8. 9:16. I thought I put the spacer/collar in backwards. But as you show there is only on way to fit it. Stick the throat out from behind the cushdrive. Then the black spacer goes on top from outside.

So the 05 doesn't require a allen on the other side?

Thanks bruh. Words on positioning the jack?

Awesome video Don't forget to Clean & Lube the Axle

Excellent video and thanks for doing what you do. My 12 point bolts on the front caliper are frozen and now stripped. (thank you Austin HD dealer for over torquing when they replaced the tire...) Can I remove the wheel without removing the caliper? My plan is to remove the wheel, drill the end off the 12 point and remove the caliper off the fork and hopefully get the bolt out. I've tried Bp blaster overnight, and also heating with torch. Heated for anywhere from 15 seconds to 2 minutes. MF will not move. Any assistance would be appreciated. My next step was going to be welding a nut on the end of that bolt. Or using an easyout. Easy out scares me in case it breaks off.

I'm gonna do the exact same thing except I'm using 1/4" on everything, hose, t fitting , filter. Except Im going to route it differently,

I own a 2020 FLHTP. It’s based on the Electra Glide, not the Street Glide.

Thanks

What scissor jack is that you got supporting the front of the bike??

Soooo close to a straight flush! That would've beaten the 4 of a kind.

EXCELLENT. I have the same breather and like you I have looked at many dif kits and nothing looked good. I will DEF do this. Thank !

Thanks very much video is top class, I have a 1999 vt1100 and this is a great help. Cheers from Ireland

man that is A BEAUTY!! love your bike!!!

do you need a 9mm aswell?

What's thr torque spec on that nut on the front wheel?

Have a 2017 m109r. Love finding these videos to learn about my ride! I would have clean out the rear of the bike with the tire off. But thats me :) Cheers!

My rear swing arm is crooked any advice? I've check for slop in pivot bushings and there is none! My tire is straight and centered in swing arm but the swingarm is not straight

I’ve got the same torque wrench “click click” 😂😂😂 great damn video man, right too the point makes it easy for any of us goons. Stay safe out there

If you shim the rear tire and take the weight off the axle, the axle will slide right out. If you get the wheel canted, then you'll have trouble.

Yooooo have u upgraded your perch clamps? I went with the trashin clamps & now I have the slot where the stock clamps were.

hello, what is that part you attached to your rear stand that holds the tire level

Good job 👍

You didn't torque anything???

How long did it take you would you say… and how did you take the old tires off the rims and installed the new ones?

This guy is a hack mechanic. I wouldn't let him touch my bike.

When removing the front brake remember to wedge open the pads....leave wedges in through install

Dude, first of all nice video. But may i ask why you touched the belt tension screw? Cant you just leave it in place, the way it is and just remove the axle so the wheel slides forward a bit and the belt becomes loose anyway? So you dont take the risk of f***ing it up with the belt afterwards.

Saved me some cash. Thank you.

Did you ever end up getting the extensions

Done in the bike trailer too. You are the man. Great video!

I'm glad you were honest here and showed some scuffling as it didn't cooperate as they usually don't cooperate. Then when it's just right, it falls in place and you really don't know what you did differently, it's just that everything just lined up. Great video! I wish you had also shown breaking the tire down and back on the rim.

Thanks for being detailed. I guess I need to start drinking crown royal to have bags for brake calibers.

What tire do u recommend??? I have a 2007 street glide and I was thinking of trying to put a bigger size tire

I'm looking to change my tires out on my 2017 roadmaster. 1st thing I need to do is buy a jack, any recommendations?

Anyone know the size that Allen key is

Great video mate thanks

Very helpful Thanks doing mine this weekend. Watched it twice and feel like I know everything I need to do.

Thank you.