Yes in essence, Be very careful though. Check what max input voltage for capacitor is or it can blow up when you charge it. Also there is some dodgy handling of the capacitor once it has been charged in this video- if you're unsure how to safely work with capacitors, especially once they are charged, do some research and get a better working knowledge of capacitors. They are useful components but despite their benign appearance they can kill if mis handled.
@@gez_4515 Yes, but the capacitor would supply the welding power. If it's a big problem, add a small resistor in series to the capacitor to charge it during short breaks between welds.
thanck's you are a free electron! but here 500 Farad is too strong, when we look first point welding, here we see, that is too strong to this thickness, was it 0.15 or 0.10mm?, so can be are correct to welding point on 0.2mm. Here you have should make 6-8 welding point to first side on cell. Is too heavy as welding point amount. With one welding point should are ok. If i use you'r capacitor, so i should make 100 Cell welding, so 200 time use, is too many second if i should 6-8 point to weld/cell side.
BEST BATTERY CHARGER DIY VIDEO - th-cam.com/video/ZN3saILbYUw/w-d-xo.htmlsi=9_nLu0vKOqfn4zi_
*Join this channel to get access to perks:*
th-cam.com/channels/WFbPzBb7dCyCWuBA-DBrMA.htmljoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
Thank you in a bind for a spot welder for 3 batteries didn't wanna spend 30 bucks for one time use 😉
I have started welding because of this!!
Very simple spot Welder, great !!!!
Ur screw driver is best😉😉
hermano esta bonito tu proyecto ,pero tengo una pregunta cuanto tiempo dura en cargar ese filtro porfa
Best welder in the world. You can weld 1 inch steel with that.
500 Farads? Yessss
Whats those clamps called? U didnt link them..
Nice trick with the magnets.
How did you put your hand across both terminals of the electrolytic and not get jolted..???
Only 2.7 Volts
Wonder how many welds it can make before need to recharge
try to change to 100@200amp cable.
I do not think so
I have 400v 1000uf electrolytic caps which I use quite often, will these be good for spot welding?
Yes in essence, Be very careful though. Check what max input voltage for capacitor is or it can blow up when you charge it. Also there is some dodgy handling of the capacitor once it has been charged in this video- if you're unsure how to safely work with capacitors, especially once they are charged, do some research and get a better working knowledge of capacitors. They are useful components but despite their benign appearance they can kill if mis handled.
@@jaileal8806 thank you, I plan to print a case for it to make it safe
@@jaileal8806 I agree never handle a charged capacitor (or one that mite be) it could kill you.
Pretty impressive. You could just leave the capacitor plugged into the psu the entire time.
Wouldn't he then short-circuit the PSU when welding?
@@gez_4515 Yes, but the capacitor would supply the welding power. If it's a big problem, add a small resistor in series to the capacitor to charge it during short breaks between welds.
@@gez_4515 use a diode
Нам вас не победить - с детьми мы не воюем!
No points for the crap loud music and time wasted watching poor taping job.
The Proper Way.
Indeed
Wow that's what I was asking 4r....😄😄
Good boy of your innovation
Hello Mr. Electron, I tried this using the 500F capacitor, but it didn't work. What else do you think can be wrong?
Cina cap?
Maybe voltage
Voltage duh
всё не так.обман
I made with car battery detachable clips and it also works well
Show it
thanck's you are a free electron! but here 500 Farad is too strong, when we look first point welding, here we see, that is too strong to this thickness, was it 0.15 or 0.10mm?, so can be are correct to welding point on 0.2mm. Here you have should make 6-8 welding point to first side on cell. Is too heavy as welding point amount. With one welding point should are ok. If i use you'r capacitor, so i should make 100 Cell welding, so 200 time use, is too many second if i should 6-8 point to weld/cell side.
U rock, thx that gave several ideas
Thanks 😊
can i have the list of what you use on these video please
Thankyou bro, awesome 💙
Work done well
A 10€ aliexpress welder does a much better job, but then again, it doesn't have super capacitors :(
Than You still need a expensive accu power supply
Yah Sirsa kis mil karta hai
Its a fake... Capacitors discharge in a flash but he spot welding it repeatedly..
No, some caps like these can stor a lot of power and dont discharge instantly
I had same doubt but I guess that's due to nickel strip resistance.
1000 capacitor UF
What do you mean
2.7v 500f capacitor.
Aliexpress sells them for $5
NICE
Great !
🕵
same person commenting on own video through different channel
Super
Dangerous using capacitor
2.7v NO WAY !
That's how a spot welder works, low voltage but high amps.
@@f-8859 I = VxR. more voltage then more current burst. double voltage then 4x power for shorter burst.
Omg.... 🤦🏻♂️
probao laz
🤮
Fake video
Have 10 of these capacitors. Tried this many years ago. And no, it doesn't welds. Not enough current. So it is BS.
Maybe some of the capacitor hooked up in reverse.
you talk too much!!