CR250 Supermoto Part 16: Handguards & Trailtech Endurance Install + (GIVEAWAY WINNER)
ฝัง
- เผยแพร่เมื่อ 10 ธ.ค. 2018
- GIVEAWAY WINNER ANNOUNCED AT THE END!!! Whats up guys! CR250 is ALMOST street legal... Watch to see how to install a Trailtech Endurance computer and speedometer, along with some Acerbis Supermoto handguards.
Made a carb change and the bike rides even better now. Also I set the suspension up and it is getting better also. The bike will get a headlight and tail light in the next build video, then it will be ready for some plates! Graphics will be the last detail.
Thanks always for the comments, advice, suggestions it all helps me so much. CR250 supermoto was definitely a crazy idea and it's even crazier come to life...
Trailtech Endurance II amzn.to/2CtEoWT
Camera: Canon 80D & GoPro4
Mic: Shure VP83
Editing: Adobe Premiere Pro
Music: Oldschool 90s Beat 2018
• Oldschool 90s Beat 2018
beat hip hop instrumental 80bpm 2018 09
• beat hip hop instrumen...
Dont engine brake pull in the clutch when u let off
it doesnt matter if you dont really engine brake w rev match etc... the oil membrane stays between sylinder and piston for pretty long time
th-cam.com/video/D0T2qltYc8I/w-d-xo.html there to you see urself
That happened with my cr 125 and I put a jet kit in it and it fixed it it had to big jets so it floods it out
should get a 2018 stadium plate they make the bike look alot newer. Bikes coming along mint👌
Dude u should not engine brake 2 stroke, always when u r not on gas put clutch in. Because crankshadt and piston don`t get enough lubrication. Engine lasts longer and does not blow up that easy, when u do not engine brake. But nice project! Sry for bad english. And n
I have never heard about this, Just looked it up... I had no idea that engine breaking was bad for a 2 stroke! Didn't understand why people were commenting in the last CR video about that so thanks for explaining! I've been riding a 4 stroke for too long engine breaking is now a bad habit but I will pull the clutch and blip the throttle from now on.
jonne
@@joonatansaarinen1283 suomi! vittu
@@mlgakipelailee0274 venäjä blyat
@@joonatansaarinen1283 puola idi nahui
Hey! You can run all the LEDs, turn signals etc off the stator for power. The relays and etc will all be such a low draw that the stock AC from the bike will be plenty
For the oil coming out id say welcome to the 2strokes world, i had a tm250 sm and i was always covered in oil, the only solution was going full throttle and burn all
robociock yeh I figured that.. thanks man I’ll try to keep her held wide haha
Sounds like it’s running really clean now
Use red rtv silicone on the pipe connection and use it on the exhaust flange
Yo tf I actually won
Not bad. Bike sounds like it's running great. Btw your shifting too soon quite a bit while riding. And engine breaking is not as big a deal as people make it seem. I wouldn't do it from a high rpm but at lower ones your fine.
For 12V You tap into the cables for the rectifier, it's a sort of round tube, usually next to the cdi, I'll have a look at my manual after and let you know which cables
Ok please let me know! As of now I'm going to hook up a 9v battery to run the backlight. And then I could do something more permanent later.
@@FULLTHROTTLEFILMZ www.rockymountainatvmc.com/oem-schematic/7 The thing youre looking for is item 5 on this page, its mounted on the frame above the servo motor th-cam.com/video/mSSYxfzvgYg/w-d-xo.html
In the plug there should be 4 wires, 2 yellow, a red wire and a green wire
The red is 12V+ and the green is Ground
Bike is dope AF
dam nice.
I would just get a small lithium battery pack and put it under the seat. You have to charge it when your not riding, but its easier than doing a stater swap
For that taillight you can get some 3m double sided tape I used it for the tailgate mat on my truck and it sticks like I screwed it in!! I have never had a problem with it coming off and it has been on for 2 years!!
Wire the exhaust rubber thingy like you would grips
Rks 25 that’s a great idea, I’m using hose clamps now but I will probably switch them for wire. Thanks a lot!
I have the same bike.
Rks 25 that’s awesome man I love these CRs
You need to get that s 7 nozzle. Watch my video on the TMX carb I want you to buy that needle to. It will give you way more throttle response.
Excellent build their bud
250race thanks man, since I already ordered the s-8 I will test that first. Then switch to a-7 see which was better. I don’t know which needle you are using?
@@FULLTHROTTLEFILMZ
Did you watch the video on the tmx 38mm?
I give two needles numbers what it is it's a taper needle. The needle is actually longer then the needle you have. And I run the 82 and don't mess with that number a nozzle it's not even worth messing with just go straight to the seven. I've already done it.
If you want the part number on the needle I have you'll have to wait till I get home later on today
@@250race ok I just watched the video you were talking about, and I definitely would like to know which needle that is! I will be buying it for sure. Also a s-7 later.
@@FULLTHROTTLEFILMZ
The part number are both there
I run the 82 it is a thinner needle.
Ok just saw that, it was at the end of the video. Gonna order the 82 then on this 2003 tmx carb
hey
Don't brake engine 😖 new piston
And put a hose clamp on the exhaust seal
Use a rivet's for the tail light if you don't find anything else.
Awesome video!😄 I’m working on a street legal pit bike build, and have the same problem with the taillight(I wanted to buy the exact same one lol) but don’t know yet how I’m going to mount it, since I also don’t want to drill holes in the white plastic.Also I wanted to buy a light bar for it and all that stuff to make it street legal again:)
Mxrider2stroke Braaap in the next build video i will show you guys how I’m gonna mount both light and power them. That sounds sweet man and thanks for the support 👍🏼
Most fenders are made from HDPE (High Density Polyethylene), which is notorious for not bonding with glue/epoxy. It is do-able, but you have to make sure your prep is VERY good and that you have a lot of bonding surface. I know it sucks, but bolting the tail light is really your best option.
Ok I will keep this in mind thank you for commenting!
Use a resistor and then set it up that way
Whats the link of speedometer??
Look into that stuff called, tough as nails. Pretty sure it will bond plastic.
Chris Sylvestre awesome thanks man!
Should have put the speedometer sensor on the back wheel, cause we all know eventually that front wheel will be up in the air and you won't know your speed 😂
Weston Wilcox lmao that’s funny man 😂 and kinda true
@@FULLTHROTTLEFILMZ Yeah we all get to that point where that front wheel in the air is habit 😂 but it's a bit late at this point to change it up 😂 guess youre gonna have to just keep both wheels on the ground all the time 🤷🏿♀️😂
SICKKK!
Hey bro !
Would you help me finding that front fender?
Looks like the Acerbis universal one but i'm not sure
Hope you'll see that !!!
Alberti Andrea yes it is the acerbis universal Supermoto fender
@@FULLTHROTTLEFILMZ Really appreciate u took time for answering my G
You just need better springs and a new exhaust gasket for that oil coming out it happened on my rm250
BackWoods Riding ok awesome thanks
Hope that's all I need, I got the same problem
@@Stuntnsinda80s it most like is if its coming from the same spot happens on all two strokes
@@JasonStaleyFitness so I should get an exhaust gasket to clear it up?
@@Stuntnsinda80s yeah i would if its doing what you think it is go ahead and get new springs with it as well and a spring puller you can find a whole kit on amazon or ebay for around 10 to 15
you can glue that taillight on the fender with some industrial glue ;-) and you are missing the rubber for the throttle assembly :-) but its a cool bike just missing a to stoked sticker
karamelsvamp didn’t even notice it was missing! The bike didn’t have it when I bought it. What glue specifically?
i cant say what glue you can use as im in denmark and i dont know what you have available there in Mexico
but you should look for something a plumber or a contractor would use to bind things together
they use many different glues in constructions that you can use !!
Have you had anything done to the suspension yet
I have done a bunch of tuning to the shock and forks to make them stiffer for supermoto. I will definitely be making a video on what changes I made, but everything was done by me.
Wow I'm kinda early :D Where are you from?
From Virginia, living in Mexco
What the name and where to find the thing you installed across the front axle for stunt? Thanks
elcincero321 they are warp9 axle sliders you can get them from motoxindustries.com
@@FULLTHROTTLEFILMZ thanks, Gracias
You could use white Nylon bolts, countersunk into mudguard to mount back light, wouldn't even see them until you were very close
www.orbitalfasteners.co.uk/en/products/m6-x-25-countersunk-slotted-nylon-screw-grade-66-natural
That's a great idea! Thanks!
Bike looks money! Thank god you didn't eat it on the test ride...close one.
Jourdon Gulick really appreciate it! Yeh I can’t lay it down until I shoot the final reveal with graphics hahah then after it’s fair game.
You better hook that speedo up for the back light, last thing I wanna hear is you couldn’t see your speed and the cop wasn’t buying it
Alex Flynn haha yeh I think I’m gonna hook up a 9v battery to it now
Heck
dont engine brake man
Hey are your tires new?
like 20 min of use
That's why the rear slipped then they need to be broken in a bit before you get all the grip
@@sleepingakidor6873 I was wondering that because... 1st time street rider here so I'm learning a lot!
The whole tire needs to be broken in so you should take angle progressively for a few kilometres
Thanks a ton man, I will definitely let these tires break in like I said new to this stuff!
I want a shirt!!!! 😭😭😭😭
First
Who else cringed @ 2:33
Travis Jalbert lol
YOU WILL MELT THE PISTON, DONT USE ENGINE TO BRAKING, use brakes....why? ...2 strokes dont lubricate with the carb closed...no gas no oil= ringstoshit
No engine braking anymore its been running strong over 30 hours now 👍🏼
@@FULLTHROTTLEFILMZ Enjoy it men! Thank for those videos 5*
Oliver thanks I really appreciate it!