HOW TO CLEAN SPARK PLUG OF BIKE AND SET GAP FOR BETTER POWER AND MILAGE
ฝัง
- เผยแพร่เมื่อ 12 ก.ค. 2024
- SPARK PLUG DIP DEEP CLEAN METHOD FOR HIGH MILEAGE!!! DIY this video will show you the best way of cleaning the spark plug with the best spark plug cleaner the tool you require to open the spark plug and how to replace it this will help to increase the and match the level of performance spark plugs be it NGK BOSCH OR CHAMPION SPARK PLUG the same method can be used for iridium spark plug
Timecode
0:00 - How to remove spark plug from engine.
0:55 - Bad spark plug
1:10 - Tools require to clean the spark plug
1:41 - Cleaning spark plug
4:00 - How to set the gap of spark plug
4:29 - installing clean spark plug and advantage of clean spark plug.
Best spark plug for motorcycle
amzn.to/3CyFGxp
Spark Plug Feeler Gauge
amzn.to/3jv1QI7
Follow me on :-
/ shakirs20224741
Instagram- / sharose85
Audio Credit: youtube : • Razihel - Love U | Jer...
#NGKSPARKPLUG #MOTOMENTOR #CLEANINGSPARKPLUG - ยานยนต์และพาหนะ
![โจทย์โหดเหมือนโกรธเป็ดถีบ [อะไรอยู่บนหัวกูวะ ... EP.4]](http://i.ytimg.com/vi/Dqlb7EZ9PGk/mqdefault.jpg)
Worked great for me as a kid thanks great video
Good video straight to the point and very informative
What paper it is sandpaper and no you should not use that you should not scratch up the court or the receiver for the electrode you had it right with just the toothbrush. Soak it in gasoline or a little bit of engine degreaser and scrub! Some people use wire brushes if you do it better be a really soft bristle one your objective is to not scratch the core rod or the receiving finger scratches or imperfections on either surface will cause it to foul almost immediately! The carbon passes around the plugs hence the reason you are cleaning it! The scratchers will accumulate that carbon very fast! Not to mention those scratches will definitely affect your Gap! Just a little bit of information for you. My route no sandpaper no wire brush no scratches! It is carbon soak it in gasoline for about a hour scrub with toothbrush it should take all the carbon off if it doesn't a little engine Degreaser will with the same toothbrush. I recommend soaking for about an hour pull from gas spray with degreaser and scrub a toothbrush. When the plug is clean rinse it in your gasoline to remove any degreaser left on the plug. then check the gap and reinstall!
Thanks again for such a great review keep it up all your videos are helpful and easy to understand
Just cleaned my spark plug. Works. Thanks 🙏
Persa
Thank...good video....i try this its make more easy to start the engine cuz your motor same as me..😄😄😄😄😄
Bhai thank you i tried your process for my fzs old version .
Good idea, I've not used petrol/gas yet. Also check to see make sure your battery is strong and tune your carburetor to run more efficiently
nice one Shak. keep going
Awesome keep em comming
Grate job bro... Your are doing well. And all the best.
Nice work awesome video
Very useful
very excellent
Keep up the great work...
NICE VIDEO :)
Thank you 🙏
Great work bro 💯💯😍😍
Very Informative....Keep up the great work...
Good way to clean it....
Very good video
Nice video
I used sandpaper the same as in this video untill i then discovered ny plugs are platinum coated, there now in the bin and a new set at £22 now fitted 😂😂
good one mate ...
knowlegable very goog
I repair/restore old outboards..after De carbonating the combustion chamber and the first time firing the motor up it is almost guaranteed that the plug will get trashed quickly..i used to just replace them. Until I looked at my bucket of new dirty plugs...so..cleaning them is cost effective for me...i use carb or brake clean and air...but then I bought that cheap harbor freight blasting machine for the finishing touch...
Nice
Anyone who has spent any time riding bikes, especially dirt bikes, has cleaned a few plugs. Especially on a 2 stroke. Miles from camp, off roading, no spare plug, and your bike craps out. You cleaned it and change it later. If you have a car with a V-8 plugs can run 5 or 6 bucks each. That's $40- $50 . So it could be worth cleaning them one time. Most people now days most people wouldn't know how to change a spark plug to save their life. The hive in a throw away world.
Its not your spark plug that needs cleaning you should adjust your engine afr its too rich plus you should use torque wrench when installing your sprk plug may you would not need to do that just a tip if you get it
Pls make more videos ☺️ ..
Hi Paul, next video is under editing will upload it very soon.
MOTO MENTOR Thank you😊
I have a 15 years old pulsar 150cc. All of a sudden my bike did not start one day so I changed spark plug and it started. I was out of station for 2 weeks and after I got back I used the bike for around 20km and now again bike is not starting.
What could be the issue? How does carbon gets into spark plug and could it has to do with engine oil.
It's been a while since I changed and since I use my bike little and mechanic said it was good. Please advice.
good work done
Tq..i have dbt there is hole to.put back spark ..in tat hole which oil present?? Nd is it req to pour certain oil.inside tat hole nd then to put back spark in tat??
No you don't have to do nothing with that no oil to be pour in that otherwise it will creat problems.
Try using steel brush or diesel
Nice also u can clean electrode with salt also......
Can you clean it with diesel?
Not bad information but u have also show how to clean spark plugs socket and how we measure the gap
Recommendations for irridium plug for my suzuki GS 150 r
I have used it for more than 4 to 5 yrs and have still kept someware at home see It will just have an extra life than normal spark plug. If you are looking for that strong spark than you need the high power spark plug cable and strong stator plate to produce strong spark which is an additional cost and still you might not be able to a vast performance it may get your eingen heated a bit. Normal spark plug is best belive me👌.
@@MOTOMENTOR Thank you for your information I ll keep it.👍
Use E3 spark plug they need no gaping and burn better and don’t build up as much carbon as normal spark plugs do and they last longer to.
For me i just use the sand paper the fine one and sand the the electrode of the sparkplug and i just wipe off the oil on the thread of sparkplug then put it back in again but if the sparkplug is already old or haven't been change for a while i recommend to change it already
i need to spark plug gap adjustment tool
How to clean the engine part of the spark plugs
With dry cloth
U have to open it first
Damm that was a tight ass spark plug
I do the same thing, use my urine sample and a toothbrush.
Urine sample? R u serious 🤣😂
is it normal to have a little bit of oil in the thread only of a sparkplug like yours?
Yes it's normal
3:17 what is the grit of the sandpaper?
Cam i use kerosine for clean ??
Kerosene doest evaporate quickly so it might create issues if we install the plug if its not completely dried up so I would recommend you to use petrol or sparkplug cleaning to get the best result.
👍
Totally gone black, reminds me of my 1st wife
Damn
She went Back to BLACK 😍🥴
Clean it for urgently is worthed
It's called HT lead my friend
Good video/info. For everyone saying it's a waste of time, go buy a new one; maybe you aren't near an auto parts shop. Or they're not open. Or maybe it's desperation alternative (on the road, no $, etc.). One constructive criticism; For me, the music was NOT an enhancement. If you're going to use music, it should be much more muted.
need to tuneup bro..your plug reading is rich..
No background music
Bro Carbon Deposited on spark plug cause Starting problem ?
2 minutes, 4 seconds of this video . The petrol is changing colour because it dissolved the copper slip from threads . In literally seconds after submerging it in petrol. As petrol is good to dissolve grease. But I never seen I could dissolve carbon. However flame does burn the carbon deposits off. But you have to be careful not to overheat them.
Look at his fingers always use protective equipment, ie rubber gloves.
how about using break cleaner instead?
I use carb cleaner but brake cleaner should do the trick
How about Rubbing alcohol?can it be used?
Sir Can we use wd40 instead of petrol
Yes you can absolutely go for it.
You could just buy a new one for like 3 tops
😂Strangely I used a tin cocacola with a bit of washing powder left for 4 hours then brushed with a metal brush. It worked
That was too strange man 🤣
Its a pretty bad idea to use sandpaper on spark plugs. Must not do that. Just use cleaning agent and soft brush.
This is totally unnecessary,i add lucas fuel treatment combined with lucas ethanol treatment,a generous amount..This is how i do it,when there is like less than a quart of gas left in the tank i start the engine and when it is hot i add a couple of ounces of that lucas stuff..This really works,no kidding..do it and when the gas runs out,fill it up with gas and run it for a mile or so and remove the spark plug and check it out...i have ngk spark plugs on 3 different bikes that i have used for 5 years..I remove them.occassionally and there is nothing to clean there..I regularly put my lucas treatment in the gas..Lucas fuel treatment for lubricity and to increase the octane and lucas ethanol treatment to neutralize the alcohol effect in the combustion.This ethanol contains a lot of water..Not good,even if its premium.it still has water in it,and leaves ashes in the form of carbon deposits
Sand paper Not good for irradium spark plugs
Hey master, After cleaning the spark plug, You didn't show how to clean the engine part where the spark plug fits
Assalawalaikum Mosin Planning to make a video very soon. Stay tuned and thanks for watching my video😉👍
Wa'alaikum Assalam dear MOTO MENTOR , thanks for your efforts, waiting for the video.
Yes. I too would like to see that as the cleaning that part seems risky as the dirt may fall back into engine..
Do mechanics clean the engine part where the spark plug fits , wg«hen they change plugs, fukidot
Brakleen or Brake cleaner is probably better.
Only useful when a person needs their last $ to buy gasoline or in your case, petrol.
When in a pinch in the middle of no where every trick, or hack is another tool in the tool box and is appreciated.
However, when the spark plug reassembles a glow plug from a Diesel engine.
The tune is to blame!
Whether it's a internal, or external engine issue needs to be established.
Assuming the engine has no major issues. Judging by the looks of your glow plug spark plug your tune is to rich.
Carburetor jetting is to rich (fat)..
Possibly a hotter plug might clean up the excessive carbon build up.. Perhaps, grabbing gears and passing queers might do the trick as well..
However, nothing can be established without a new plug, or at very least one with zero deposits off of the electrode inside the plug by using a plug sand blaster..
By not removing carbon deposits off the electrode will create excessive carbon build up, oil contamination, and a lazy shitty performance!
Remember, Lean is Mean when making Horse Power just don't get greedy!!
Instead of cleaning an expensive spark plug, you need to figure out why your bike is running so rich. Having the bike at proper tune is a better way of making more power and better fuel economy.
You also take your spark plugs to the dentist?
I don't clean I replace with new
CHEONG KC money waste
@@carmelgimenez620 but it not the best for the engine
After clean the spark plug, you need to tune-up your carb.
why tho
@@Jetski1337 because it's running too rich.
Bison
Someone told that the plug be cleaned using salt for better conductivity. Is that true and advisable ?
First of all thank you so much for watching my video...see cleaning with salt and water is all nonsense even I have seen that video with millions of views that person is just miss guiding us. the reason why it's not recommended is because metel with salty water can easily catch rust its common sense and it's scientifically proven we shouldnt use water with salt to clean any metel part. please search it and see it on Google if u have any doubt. The other reference he gave is that it will increase conductivity by giving reference of earthing whivh we do at home to ground the electricity. See we are talking about bike the earthing is given directly on metel part of the bike and not on a actual earthcrust... I can give u more example to expose him and I was planning it to do then I just left it.. However i think I should make a video on this very soon.
Dumbass
Salty water can cause corrosion on the metal
Please stop the background music
Use coke instead. Works way better. Soak overnight.
I never clean my sparkplugs I replace them with new ones
Clean it when you need to check the carburator in this case that sparkplugs still good!!!!!!
New spark plug ka cost kitna he
100 ke aspass
why not just replace the plug? you waste 1-hour cleaning this thing, A new one is less than 100 bux??
approximately how many kilometers does a spark plug last?
13k to 15k ... mine was changed after 14k coz it got faulty so. You can also change after 10 to be at a safer side or carry a spare one until you feel you have some major issues.
running rich may want to find out why, and put a new plug in it
Just like your video would be a lot better if you speak better English what did you use to clean the spark plug with and how did you clean the engine where the spark plugs goes back in?
wait i clean my plug with petrol and now its damaged . my bike didn't start . only aftr i replaced it started .
I have me doing this since 10yrs without any issues ... did you let it dry you spark plug after cleaning it? Or you installed it immediately and how old you spark plug was? Coz i am doing the same since years infact my friends all the local mechanic follow the same steps and we have never come across such issues.
lol . How come . mayb i installed befre it dried properly . but i kept in the sunlight for about 5 to 10 minutes . .maybe i shud have wait for hours or?
and ya my plug was one month old
T
itu yamaha byson di indo ya?
Yes
Its the worst Cleaning spark plug ive ever seen. The best way is using a brass brush and a fire burner.
The plug in the video did not need "cleaning" Just replace with a new one. This is to much sugar for a dime
this method is lame, if you really want to clean your spark plugs go spend $25 for a pneumatic plug cleaner or if you have a hand held sand blaster just use it, takes under a minute per plug and they get a lot cleaner then using this method, I probably clean a half dozen or more motorcycle plugs every week with my hand held sand blaster for my kids and the other kids in the neighborhood and I haven't had to buy any new spark plugs in a couple years
This is the best solution.I give faith on it,
Not everyone have toolkits like you do.
What a cheap guys.. Just buy new one and replace it..
Too loud music
What the fuck is he saying? I don't understand what that liquid is I can't understand what he's trying to say... Bertrol? Petrol?
Or pay 3 dollar and get a new one
Dam just give up and buy a new one because thoughs were not the same spark plug from the start to end of the vidio
Man it's the same sparkplug believe it or not.
Your gas isn't clear like in the usa
spark plugs are $3.50 each. Not worth the time and effort cleaning them, only to replace them a few months later.
This is obviously another country, they might not have the resources that america or canada or England would have. And if they have less sparkplug options... Then its gonna cost a lot more than $3.50
Itsonly cost 1.5 dolar or maximum 2
Official noob player yt It depends on you car/bike. I have 6 iridium in my car any they are £20 each, supposedly long service life of 60k miles but something like this video could be done every 10k if they needed
Then why are you watching this video. It is obviously not worth your time?
too much money..
pag los los inum pkag gaas dong
Comprali e fai prima NO?
It is not optimal it is rich so milleage loss check ur ignition coil cdi unit carburettor
സൈക്കിൾ ലോകം thts true
That right too much that why the color of top sparkplugs is black
wtf is that petrol ?
Gas
That plug is an
NGK (4929) DPR8EA-9 Standard Spark Plug, $3.22 on Amazon. Lame idea, very fouled plug, and petrol doesn't clean too well.
Uh... What the hell kinda fuel is that... Kinda looks like kerosene. That would explain the oiling of the plug.
It's petrol. He said himself.
Looks like two stroke mix
Go buy new plugs. Old dirty plugs are done. Do you & your engine a favor...