Harbor Freight 12-Ton Shop Press Assembly & Modification Upgrades
ฝัง
- เผยแพร่เมื่อ 9 ก.ค. 2024
- We assemble a $150 Harbor Freight 12-ton shop press and do a few must have modifications to make it easier to use and work with.
Locking Caster Wheels: amzn.to/3RL8id5
3/8" Jack Release Knob: amzn.to/3CiwVIo (they also have a 7/18" which is larger for maybe the 20-ton)
Pneumatic Bottle Jack (cheaper than HF) - amzn.to/3rX0xq5
----------
Support the Patreon: / tunerwithkids
Merch Available: teespring.com/stores/tuner-wi...
Follow Me on IG: / tuner_with_kids
For questions and inquiries: tunerwithkids@gmail.com
-------------------------
#harborfreighttools #shoppress #12tonpress
0:00 Intro/Unbox
2:50 Assembly
4:42 Test Use
5:25 Upgraded with Casters
8:07 Billet Release Knob
8:30 Future Pneumatic Jack Upgrade
Disclaimer: "Tuner with Kids", the alias for the human content creator for this TH-cam channel, is not responsible for any damages, injuries, losses, or liabilities associated with any repairs, upgrades, or maintenance performed on yours, or any elses, vehicle/property whatsoever. No warranty, express or implied, is made as to the accuracy or completeness of any information provided within this channel. Viewing and using the “as-is" information of this channel is totally at your own risk. Always wear personal protection equipment and follow appropriate vehicle manufacturer service manual guidelines with original manufacturer parts only when performing any repairs, upgrades, or maintenance upon any vehicle/property. Please note that some of the links provided are affiliate links and I may earn a commission if you purchase through the links. I use all of the products shown and recommend them because they are from companies I have found to be helpful and trustworthy. Please let me know via email if you have questions regarding any of the products/tools used. - ยานยนต์และพาหนะ
The video that I needed. I assembled it this morning, but was concerned about the gap between the vertical rails and the top portion of the press. I see that you just tightened until the gap closes. Great idea with the casters! Just ordered the same set.
Best addition is a pneumatic jack then start the other upgrades. A light duty trailer crank is great too.
Bought the same one to press a driveshaft back together. I did find that the bottom crossbar can get in the way of long pieces like that and that I needed to elevate the feet of it to get adequate height for long pieces. Outside of those small nits, it is a very useful piece of shop kit
They make a kit to use it as a bench brake for putting bends in metal for making brackets; etc.
Great review, I purchased those casters from you mr link thank you!
I watched another guy's video and all he did was dog this thing. Appreciate your review and the mods. The way I look at it is that I'm not paying much for it. I don't mind making a few mods. Very nice review. New subscriber here.
7:03 I took those press plates to a mom/pop machine shop and had them true up the two surfaces. Mine were pretty sloppy from the factory so I just had him do about an 80% cut otherwise they would have been thinned down toooo much. Also, I drilled holes in the corners so I could drop in some pins to keep the plates from escaping under load.
7:31 Glue on some magnets in the channel to hold the handle.
7:48 Drill a hole and insert a hair-pin with a fender washer.
8:19 That knob came from where?
Knobs on Amazon. See link in description.
Great insight Binh. Sometimes smaller is the better option.
Cut the pump handle shorter.
I think mine is 9 inches long.
Makes it easier and faster to pump the jack.
Good video, thanks for the info. I am deciding between this and the 20 ton right now.
The 20 ton is huge and takes about 1.5 times more space to store. Much more heavy duty. I was planning on getting that but once I saw the side by side, I went with the 12 plus I was able to used a 10% off coupon.
@@TunerwithKids today, Nov 15 of 22 the 12 ton is 139 with coupon, and the 20 ton is 259 (no coupon found) so the price gap is pretty huge as well! Thanks again.
Great video, Binh. For the handle, I zip tied a U.S. General 18in magnetic tool holder (item 60433) to the top of the press. It’s 4.99 at HF.
Good idea. I have a few of those around the garage.
Yes, I know. Just got a 12 ton press. Need to figure out how to look after the Jack - specifically, what kind of Jack Oil???
Need press to fix *MILL.*
I need one for my Integra. About to just buy one too.
One of my most useful tools lately for pressing parts and bushings.
i just got the 12 ton at harbor freight and they told me if i want to upgrade to 20 ton, then what i paid for the 12 ton will go towards the price of the 20 ton
never heard of that or any kind of trade in.
Great video/content!!
What size caster wheels did you get? 3/8” or 1/2”??
Check links in description box. They are common Amazon item.
Don't drop one of steel plates on your foot.......... be careful. The painted surface on my press is like glass and my plates slipped off super easy.
Where did you get that (knob)
Check links in description
He said knob lol came here to look for a comment cause I was saying the same thing to lol
What did you pay for it
Like $153, it was a 10% off coupon sale weekend.
Purchased this to press the valve guides out of a 4.6L ford PI heads and took almost 45 minutes to do 1 single guide the rest luckily came out easily with snap on air hammer using the proper 7mm tool made expressly to do this. Used to have a 20 ton press and the amount of force needed to press out this lil valve guide seemed to tax this pos made in china press to the absolute limit. returning it tomorrow as for my intended use will end up costing me more to fix what it breaks .. Instead buying an actual valve guide removing tool that can be easily done with 1 person. If I need a press in the future will simply get a 60 year old 20 ton press off craigslist. old tools trump harbor freight crap 99% of the time.
fyi: I had an application where i was near maxing it out. I needed to remove the pressure screw, and put it back in (bleeding it a bit) to get it to really torque down. Then I had to very tightly re-insert it with the handle.
I'm mentioning this since you made a custom billet handle, mine is now too hard to turn where that would be viable
We do not need all your opening pointless chatter .......
We don’t need your stupid comments