I feel like it’d look better with the mid bend bars. The low bend bars get engulfed by the gauges. But I do understand it’s more comfortable for you with the low bend bars
It’s funny you hit the nail on the head about the gauges protruding because of the low bend. I couldn’t figure out what it was that was bugging me , but it was the gauges protruding. I’m glad I went with Arlen ness 520-042 black bars. The part number is stainless finish but they sent me black instead and I’m thinking black might be better
i decided today to go with Kraus. they had a bike done at the dealership and it did not have that mess you have in the front area. i think it just takes some time and thought as they had one shiedled like cable that went into the fairing and no other loose wiring. the kraus is much more expensive i saw but the quality looked better.
Has nothing to do with kraus or Arlenness. The is still wasn’t down properly. I just recently got it redone and posted a video on it. Cables are tucked and it’s clean.
Keeping the nassel at the base does this setup a disservice. I can't believe your dealer thought this was a good idea, or near a finished product. I don't think the setup is intended to keep the nassel but if that's the case I believe Dirty Bird sells the part where the gauge holes are solid and not cutout to enclose all the wiring. You can cut holes for the risers in them.
Bro...the dealer did a terrible job on the installation. Check out john maxwell vid when he installed risers on a bagger. He cleaned up the entire wiring. That open area with the wiring should have been removed and wires should have been tucked away either into the bars or into the fairing. Slap that dealer and get a refund. That is a half assed job
Just had this exact same setup done to my 21 RG. I had them add the raptor plate from Kraus. I'm very surprised they didn't clean that wiring up with some heat shrink to protect it though. Anyways these bars do make it ride like a dream. 🤘💯
Buddy it looks good.. can you do some slow speed skills with those bars.. 18 + feet figure 8's, U-turns etc.. also at 10:08 to 10:14 the audio cuts off
@@3percentmick705 you stated in the video it does not obstruct your view at all though. Are you still able to manipulate the touch screen on the infotainment unit without much hassle? I just ordered this full kit for my bike, so gonna send it either way, just curious.
This video is perfect. Except it hasn't made my decision any easier😆 I've been debating between this, and the Thrashin setup. The built in cluster saves some extra BS and gives it a lot cleaner look. Now that it's been a year, are you still liking them?
Totally agree. Arlen Ness is known for having high quality stuff. Not sure why this was overlooked or maybe their solution was something MK didn’t want to do. 🤷♂️
This is not the case, Kraus is a similar setup and looks great when wired properly. The key is to extend and wrap the wires so you can see a clean triple tree bracket. The dealer that did could've done a way better job.
I think he said he is 5’ 7” on the video! I think I’m about 5’7” or 5’6” but I can flat foot it🤔 my bike is all stock. 2022 road glide st! I’m looking for taller bars to.
To be honest with you bro you should have brought it to Mike at Get Lowered Cycles. On his Road glide he has the Kraus Tbars and he did my thrashin supply Tbars and it was clean... No exposed wires.... Those 🤡 at Harley let your bike go out the door looking like that... SMH
Bro looks really good 👍 It's your bike so, who cares. The most important think is your comfort and ease of use of your own bike. Just realize you're kind of tip toe a little bit. What is your inseam?
I think the gauges are now in a perfect position. Not so with the stock gauges on the Low Rider - having to look down, taking your eyes off the road is one of the worse legacy designs from HD.
So you can't run Thrashin bars with these risers, they aren't wide enough & won't allow full rotation of the bars & as far as the wiring talking about cutting it, holy smokes lol. Buy the wiring extensions, take your fairing off & headlight out, put the extensions on, pull them through & that's how you clean the wiring up. It's absolutely astonishing that this is a TH-cam influencer.
It was cool how you stated your height and showed the side profile
I have the Kraus Pro Wolf Setup. My dealer pulled all the wires into the fairing.
I feel like it’d look better with the mid bend bars. The low bend bars get engulfed by the gauges. But I do understand it’s more comfortable for you with the low bend bars
It’s funny you hit the nail on the head about the gauges protruding because of the low bend. I couldn’t figure out what it was that was bugging me , but it was the gauges protruding. I’m glad I went with Arlen ness 520-042 black bars. The part number is stainless finish but they sent me black instead and I’m thinking black might be better
i decided today to go with Kraus. they had a bike done at the dealership and it did not have that mess you have in the front area. i think it just takes some time and thought as they had one shiedled like cable that went into the fairing and no other loose wiring. the kraus is much more expensive i saw but the quality looked better.
Has nothing to do with kraus or Arlenness. The is still wasn’t down properly. I just recently got it redone and posted a video on it. Cables are tucked and it’s clean.
Love the set up and the bike! Did you use a kickback plate from Kraus or any other type?
Keeping the nassel at the base does this setup a disservice. I can't believe your dealer thought this was a good idea, or near a finished product. I don't think the setup is intended to keep the nassel but if that's the case I believe Dirty Bird sells the part where the gauge holes are solid and not cutout to enclose all the wiring. You can cut holes for the risers in them.
@desmo big bear performance makes a nassel to replace the factory. I opted out of it and just had them clean up all the wiring with heat shrink.
Bro...the dealer did a terrible job on the installation. Check out john maxwell vid when he installed risers on a bagger. He cleaned up the entire wiring. That open area with the wiring should have been removed and wires should have been tucked away either into the bars or into the fairing. Slap that dealer and get a refund. That is a half assed job
Just had this exact same setup done to my 21 RG. I had them add the raptor plate from Kraus. I'm very surprised they didn't clean that wiring up with some heat shrink to protect it though. Anyways these bars do make it ride like a dream. 🤘💯
Beautiful bike my Brother. Suggestion, replace all reflectors and lighting with Custom Dynamics smoked LEDs...
Buddy it looks good.. can you do some slow speed skills with those bars.. 18 + feet figure 8's, U-turns etc.. also at 10:08 to 10:14 the audio cuts off
Happy for ya brother.. For me, I would be put off by the possibility of them blocking the infotainment system and Map.
More often than not, the phone gets mounted to the bars and used for music and gps anyways because the infotainment screens kinda suck for that.
@@3percentmick705 you stated in the video it does not obstruct your view at all though. Are you still able to manipulate the touch screen on the infotainment unit without much hassle?
I just ordered this full kit for my bike, so gonna send it either way, just curious.
Did you also get the method ignition switch accessory? And does it allow you to still use your fork lock with the risers?
Yes and yea it does
So all you need is the riser and the bar?
Did you get the method top triple tree? You can remove the whole guage pod housing. You have to have a crafty wiring guy to clean everything up.
I didn’t get the triple tree but yes I’ll Deff be finding someone to clean it all up
This video is perfect. Except it hasn't made my decision any easier😆
I've been debating between this, and the Thrashin setup. The built in cluster saves some extra BS and gives it a lot cleaner look.
Now that it's been a year, are you still liking them?
I’m still stuck here as well. My thrashin is on back order still
I friggin dig it. I like the gauges being on top instead of like all the others. Dope.
Thanks man and yea super different and cool
Arlen Ness should have had a solution to the exposed wire problems. Not like them to half ass a mod.
Totally agree. Arlen Ness is known for having high quality stuff. Not sure why this was overlooked or maybe their solution was something MK didn’t want to do. 🤷♂️
This is not the case, Kraus is a similar setup and looks great when wired properly. The key is to extend and wrap the wires so you can see a clean triple tree bracket. The dealer that did could've done a way better job.
looks like a good riding position with the new bars
Did you use a pull back riser adapter under the method risers or is the Method risers on top of the triple tree top clamp?
Watch my latest video on it I explain it all on there
Wow! It's such a useful and healing video.💕💜❤
The road glide motorbike is stable and has excellent performance.
💖💞💝 Have a happy day.
I Noticed you don’t have a prospect patch on what’s up with that
Did you also get the top triple tree?
Dod you got wiring situation. Covered up yet
Yea I made a video on it
@@Marvelkid87 yeah found video last night
In your honest opinion, would the high bend bars from Thrashin also fit? Looks like the gauge cluster might interfere with the bend.
I don’t think it’ll interfere with anything. I might switch it to a midbend
It does interfere and you cannot do it. You have to run the Arlen ness Moto bars
Have you thought about customizing your seat so that it provides a lower profile without sacrificing too much of the comfort of the seat?
what are the handle bars ?
how tall are you? I just got a road glide and I feel like my feet are about at the same stance as yours. Do you have trouble with the kick stand?
I think he said he is 5’ 7” on the video! I think I’m about 5’7” or 5’6” but I can flat foot it🤔 my bike is all stock. 2022 road glide st! I’m looking for taller bars to.
The bars look good but if I ever do T bars I’ll go with thrashing supply T bars because they thought of everything.
Looks good. Wiring doesn’t bother me too much and once you get a black plate on it, it’ll be clean. Mos def makes the bike hotter.
Bro question...so the triple tree back plate only function is to cover up those wires from looking at it?
Just pull the excess wiring into the fairing and zip tie, use wire loom to clean up the exposed wire
Try to find a cover that you can put on tap of does cable's
This looks absolutely dope, I love it. Could mid bend bars fit?
Yes I just don’t want anything higher then what I have with this setup
These gas prices tho...we all have to stand up against these ridiculous gas prices
Your bike is fire brother.
Should put tweeters in that open space.
That actually sounds like a good idea
She's looking Real Nice 🤘
Looking slick mate, nice purchase!
Looks awesome bro... Road Glide T-bar gang! Haha
Yes sir! 👊🏽😎 I have an idea for a video with both bikes bro
To be honest with you bro you should have brought it to Mike at Get Lowered Cycles. On his Road glide he has the Kraus Tbars and he did my thrashin supply Tbars and it was clean... No exposed wires.... Those 🤡 at Harley let your bike go out the door looking like that... SMH
Ima see what I do with the back plate and stuff and see how it works out if not I’ll find another alternative.
Bro looks really good 👍
It's your bike so, who cares.
The most important think is your comfort and ease of use of your own bike. Just realize you're kind of tip toe a little bit. What is your inseam?
Facts! 🤩👊🏽 30”
Awesome my G… Bike is dope, keep up the great videos.
Some 1 in lower blocks will help you out alot.
Looks nice. Keep the content coming.
Looks really good. 👍👌
Thanks bro 😎👊🏽
Finally! 😬 Looks awsome!
🤩👊🏽
I think the Dealership should have been more helpful with the wiring situation. At least give you some solutions. 😎 videos keep putting them out👍
looks sick bro!!!
👊🏽🤩
Very cool!
😎👊🏽
Empire collection is nice
Thrashing supply bars and everything they sell 🤘🏽
Looks great 👍🏻
Looks nice!
🤩👊🏽
🔥🔥🔥🔥🤘
👊🏽😎
I think the gauges are now in a perfect position. Not so with the stock gauges on the Low Rider - having to look down, taking your eyes off the road is one of the worse legacy designs from HD.
Yeppppp
So you can't run Thrashin bars with these risers, they aren't wide enough & won't allow full rotation of the bars & as far as the wiring talking about cutting it, holy smokes lol. Buy the wiring extensions, take your fairing off & headlight out, put the extensions on, pull them through & that's how you clean the wiring up. It's absolutely astonishing that this is a TH-cam influencer.
Not a fan of that set up man it looks messy
“Organic?” Lol
Awesome my G… Bike is dope, keep up the great videos.
Thanks man