PL62X LELIT Marax temperature probe broken or disconnected -probe alarm-led-

แชร์
ฝัง
  • เผยแพร่เมื่อ 14 ธ.ค. 2024

ความคิดเห็น • 18

  • @repetto74
    @repetto74 2 หลายเดือนก่อน

    Hi, I have my Mara X PL62X which cannot control the steam pressure anymore! It goes above 3 bars quickly and safety valve pull out excess steam. The power button led is steady when I switch it on. Tried both HX Mode and Normal mode and same steam pressure problem. Is that the temp probe to be replaced??

  • @Darklink88600
    @Darklink88600 3 ปีที่แล้ว

    Hi ! Thanks for your video! I got a question about that.
    When warming, my lelit stay most of the time around 2.75 bars and then go down when it reach the right temperature.
    But thoose recent days, the machine start sometimes to go over 3 bars for at least 1 minute (a lot of steam appear at the bottom of the machine). Does it sounds good to you? Does I need to change a probe?

    • @lelitinsider2977
      @lelitinsider2977  3 ปีที่แล้ว +1

      hi,
      please send the data label at care@lelit.com,
      meantime try to use the machine in hx mode for some days

    • @Darklink88600
      @Darklink88600 3 ปีที่แล้ว

      @@lelitinsider2977 thanks a lot ! =)

  • @Kingofkotelett
    @Kingofkotelett 2 ปีที่แล้ว

    Hi, thanks for the video! I have the issue in the 1st scenario on a new machine, what would you advise me to do? Thanks.

    • @lelitinsider2977
      @lelitinsider2977  2 ปีที่แล้ว

      please contact your reseller or send an email at care@lelit.com
      th-cam.com/video/jU4kYyTyyUM/w-d-xo.html

  • @terrybuckland7018
    @terrybuckland7018 2 ปีที่แล้ว

    What should I do if the water probe light doesn’t turn on at all? But everything else seems to work normally

    • @lelitinsider2977
      @lelitinsider2977  2 ปีที่แล้ว

      it can be the led broken, can you send a video at care@lelit.com? in the mail please send also the foto of the serial number of your machine

  • @00shrshr
    @00shrshr 4 ปีที่แล้ว

    Hi my three day old Lelit Mara X has all three lights flashing. I just switched on the machine with the temperature switched changed to I. Removed the water tank, saw some white toothpaste like gunk to the entrance of water tank to machine cleaned it up... but problem persists. Any idea why?

    • @lelitinsider2977
      @lelitinsider2977  4 ปีที่แล้ว +1

      th-cam.com/video/ndNuFK-fWM8/w-d-xo.html look at 2.20, is it the same case?

    • @00shrshr
      @00shrshr 4 ปีที่แล้ว

      @@lelitinsider2977 no the on/off switch starts blinking with the three pilot lights when i switch it on itself. Looks like in your video that the machine was ready to go.

    • @lelitinsider2977
      @lelitinsider2977  4 ปีที่แล้ว +1

      @@00shrshr th-cam.com/video/O47N_Oyb2aA/w-d-xo.html it can be this

    • @00shrshr
      @00shrshr 4 ปีที่แล้ว

      @@lelitinsider2977 yes you are right the micro switch is stuck inside and it keeps getting stuck. Will wait for the service centre I bought it from to get back to me since it’s only 3 days old so it shouldn’t have this issue.

  • @SylvainProov
    @SylvainProov ปีที่แล้ว

    Hello ! i have a similar problem, the temperature front led stays off, but everything seems to works, I did some expressos today. What do you think ? can I change myself the led ? Thanks for the video ! i love Lelit :D

    • @lelitinsider2977
      @lelitinsider2977  ปีที่แล้ว +1

      if the machine works you have to change the LED
      th-cam.com/video/255qV4mMavc/w-d-xo.html

  • @eddyr9379
    @eddyr9379 4 ปีที่แล้ว

    What happens if all the flights are flashing , the power and temperature

    • @lelitinsider2977
      @lelitinsider2977  4 ปีที่แล้ว

      It can be the standby mode on/off

    • @lelitinsider2977
      @lelitinsider2977  4 ปีที่แล้ว

      th-cam.com/video/ndNuFK-fWM8/w-d-xo.html look at 2.20, is it the same case?