How To Program a Jandy JEP-R Variable Speed Pump Controller
ฝัง
- เผยแพร่เมื่อ 25 ส.ค. 2024
- In this video I go over the programming of the Jandy JEP-R Variable-Speed Pump Digital Controller for the Jandy Variable Speed pumps. The JEP-R looks complicated to program but is actually quite easy. The JEP-R overall is a good controller for your Jandy Variable speed (VS) pump.
The JEP-R can hold two schedule speed programs and up to a total of eight different speeds. This is where it can be confusing. You can program only two speeds to come on at set times. For example you might want low speed to run from 7:00am to 1:00pm (eStar speed) and Speed 2 to run form 1:00pm to 3pm. So you can set these specific daily run times in the JEP-R in the first two buttons on the controller.
Buttons 3 and 4 can be programmed for a specific speeds (the speeds on a VS pump are referred to as RPM). But they can only be set for a run duration time, like 2 hours, and button 3 and 4 will need to be manually started by pressing the button. There are also optional speeds 5-8 that can be set and accessed thru the menu - these will also need to be manually started.
So overall your programming should be focused on button 1 (eStar) and button 2 on the controller. There are factory set defaults also for all of the buttons, eStar is set at 1750 RPM and Buttons 2-4 are set at 2750 RPM. In the video I show you how to easily change both factory preset speeds.
The main question I get is what run time and RPM should I set my VS pump to? The answer to that question depends on a lot of factors. How big is the pool and overall flow rates are the main factors. For a larger pool, the pump will need to be set to run longer or at a higher speed. To determine the ideal run time and RPM, installing a flow meter is your best option. I like the FlowVis Flow Meter seen in this video:
FlowVis® Flow Meter - H2flow Review & Overview: • FlowVis® Flow Meter - ...
Installing a flow meter will give you the exact gallons per minute (GPM) of water flowing from the skimmer, into the filter and then back into the pool. Without a flow meter you can make an educated guess based on your pool equipment.
As a rule of thumb you want to stay under 3000 RPM as a high speed setting with button “2.” This will maximize your energy savings and most pool cleaners can be run at 2600-2800 RPM. This also includes solar and a salt cell. The only time that you would use a higher RPM would be for a spa spillway or when you are using your spa and want the full effect of the jets (3450 RPM).
Also, you should run your pool in low speed for the majority of the time. So a common set up would be 1750 RPM for 8 hours a day and 2600 RPM for 2-3 hours a day. Again, this all depends on the pool size and the pool flow rate. Here is a video that illustrates this:
Variable Speed Pump RPM, Watts and Run Time EXAMPLES: Featuring Jandy iQPUMP01: • Variable Speed Pump RP...
So the Jandy JEP-R is an easy to use and a moderately easy to program variable speed controller.
To see a video on how to install the JEP-R:
How to Install a Jandy JEP-R Variable Speed Pump Controller: • How to Install a Jandy...
Other Videos in this series:
Jandy iQPUMP01 Smart Phone VS Controller: • Jandy iQPUMP01: Instan...
Variable Speed Pump RPM, Watts and Run Time EXAMPLES: Featuring Jandy iQPUMP01: • Variable Speed Pump RP...
Jandy VS FloPro 1.0 HP Pump Installation Part 1: Unboxing & Walk Thru: • Jandy VS FloPro 1.0 HP...
Jandy VS FloPro 1.0 HP Pump Installation Part 2: Plumbing in the pump: • Jandy VS FloPro 1.0 HP...
Jandy VS FloPro 1.0 HP Pump Installation Part 3: Wiring the Pump (watching now): • Jandy VS FloPro 1.0 HP...
Variable Speed Pump, money saving benefits: • Benefits of a Variable...
How a Robotic Pool Cleaner can Maximize your Pool's Energy Savings: • How a Robotic Pool Cle...
Visit my Website: www.swimmingpoo...
TH-cam Video Index - A list of all of my videos:
poolmandave.blo...
Follow Me:
Google +: plus.google.co...
Blogger: poolmandave.blo...
Facebook: www.facebook.c...
Twitter: / mrdgvb1
Support me on Patreon: / edit
THANK YOU! User's manual is a joke and makes it look so complicated....glad I thought to look on youtube for help! REALLY appreciate your efforts.
I’ll always support your content, you’ve helped my pool tech career countless times.
You’ve probably trained over 10,000 pool guys by now on something via videos… maybe 50,000. You’re amazing man, I hope it brings you great prosperity.
The great thing is that if I have to watch this a hundred times, that's fine.
Thank you for this video! Wish it was written down too! It's a terrible controller! Our installer said to call him and he'll make any changes needed to the program. Probably since I complained about it so much. LOL (I'm sure for a fee he'll come out!) This video has helped us so much! Simple things like shutting it off is not simple. Thank you for that info in the comments! We had our jets turn on/off for no reason. The installer said it was probably something with another part of the pool. I read it's our brand new pump. If it runs on low speed air can get into the system, then turns the jets on to release. The vacuum doesn't move on the star settings either. So now we run the high settings at 95% of the time. Doesn't save electricity as advertised. But with this video, you explained you CAN change the star setting! My installer told me it was un-changeable. Just wanted to say thank you! No only this was video was informative it is an outstanding "how-to" video!
Thank you for this video. I finally set my pump run timer after having it Running for 24/7
I have to agree with Avi just below. Trying to get this on the first time through made my head explode! The pool company I had install this pump said they programmed an eStar start-stop time but my pump did not shut off at the time they said it would. So, unfortunately, I'm going to have to learn this. I figure I'll just write all down on paper. I have the manual but it simply wasn't that clear - a picture is worth a thousand words.
I actually tried the remote control first but it would not connect when the iAquaLink app was installed on my Pixel 2. I got it to connect once on my old Nexus 6P but when I started using it, it died. I realized that I needed to control the pump from the physical control panel, not the stupid app. If you read reviews about the app, you probably won't want to use it either. Another "unfortunately", if you use the app, you can't use the pump's physical control panel (brilliant design). I had the pool company remove the remote control panel entirely so I could control the pump with the physical control panel as shown in the video. I'm hoping that someday I will be to understand this video and actually program the pump correctly. I'm kinda wary about this because the pool company guru was not able to do this.
I kinda miss my old Hayward single-speed pump. You just set the trip-bolts on the wall-mounted timer and it always works. Ah, the good old days!
Thanks for posting this! I don't remember your name but you were my pool go-to guy when I first moved into this house and needed pool information.
It is overly engineered. You can switch to the iqpump01 also - much better.
I should have never changed from my old pump. Hate this pump.
He goes so fast. I got the times figured out but I can’t figure out why my vacuum won’t work. Pool service showed up when I wasn’t home for our first service and changed my settings to waterfall. I don’t have a waterfall 😂
😂😂😂😂
Play the video at slower speed.
Are you able to adjust the cleaner (4) schedule? Or is there preset settings for it to run?
You should be able to. The manual will guide you thorugh it.
Great video. Question- on a jacuzzi that waterfalls into a pool...how would you increase flow of waterfall?
You would need a set speed at a higher RPM depending on how much waterfall effect you like but 3100 RPM should do it.
Thanks man. Super helpful.
Thanks man I just upgraded and wasn’t sure about the settings of my installer 👍🏻
Not an easy device. Glad the video helped!
Great tutorial, thank you sir!
I wonder if the prime speed can be changed, I did a little digging with no luck
You can in the system menu.
@@SPL I found it! Thank you so very much for these videos 🙏🏼
thanks for this dude
What to do mine won't turn on pump says key pad is locked how do I un lock
This video saved me. My installer didn't explain the programming very clearly but you made it all make sense. Thank you. My question is what is the best way to stop and start this Jandy pump when backwashing the filter? Will it prime every time?
this would be a very helpful question for him to ask answer. great video, thanks
Thank you so much for this video, if it was not for you putting this video together, I could never program this! I would like 10 minutes in the room with Jandy engineers, to beat the **** out of them!
Great video. thank you very much
I read the manual and was like am I the dumbest person who has ever lived?
I believe it is the other way around. The engineer who created this is the one.
Well the problem is that the pump goes into priming mode when switching from one-speed program to another regardless if the program times overlap. So to avoid this unecessary wear and tear on the pump I install the IQPUMP01 device and the pump no longer primes when changing program speeds. This is not my preferred situation but it worked.....
Hi Michael, how's the IQPUMP01 holding up? Do you find it reliable? I'm on the fence of buying that... Because I read a lot of mixed reviews on that. Thanks in advance!!
Thanks for posting this! I don't have a manual and was going to have to pay a company to come out and program it for me.
Your very welcome 👍
What’s the difference between Filtration, speed and cleaner???? Which one do I use my pool sweep with?
Those are just to help you recogonize different speeds. Label however you wish.
Thank you
How do you unlock a locked keypad?
after manual overriding to use cleaner or waterfall, how do i return it to scheduled programs?
You can hit the eco button to the left and that should get it back in schedule mode.
Great video. Thank u!
Hi how do i program the controller when I can read the display. The controller is about 10 years old and worked fine but some how I lost the run settings. Any help is appreciated. Thanks.
You may kjust need a new one. They are pretty inexpensive.
On point!
Ho do I set the pump to run for 24 hours? I will be adding phosphate remover and directions say to run pump 24 hours after adding.
This is tougher. You will have to put a program run time from 8:00 am turning ff at 7:59 am
🙌 thanks
Hey I was wondering if there is a way I can heat my pool with this controller and if so how? My pool is really cold and I wanted to make it a little warmer .
You would need to turn on the heater from the heater button after you start the pump
@@SPL thank you! I know nothing about how pools work so is there anyway you can explain is a little more though and what does rpm mean?
GREAT VIDEO!!!!!
Hi again,
How do you unlock the pump?
Thanks,
Tony
Hold both arrow keys for 5 seconds.
@@SPL Thanks for your help again 👍
how do i change from military time to reg standard time
Help! So confused…I have a salt water pump, and this is the controller I have along with a hand spin dial that’s separate…does the timer on the hand spin dial control just the salt chlorination? Basically what does what? It’s easy to set the hand dial, but would like to know what it turns on. Also the Jandy I was able to set the correct time, but how do I schedule a time on and time off? I’m trying to follow you but it’s not working out right. Also does the salt chlorinator have to come on after the pump comes on …please help me I’m so confused.
You would need to match that yellow timer up with this system so the salt cell turns on after this one is up and running.
How do you know the correct speeds?
You can set them as a rule of thumb like this. Low speed 1800 RPM for 10 hours. Medium speed 2400 RPM for 8 hours. This is about 2 hours of a standard speed pump electricity use, even though it is 18 hours
Can I add the iQPUMP01 to my pump or iaqualink control panel? I have a vs flowpro but programing is non existent, do i need to install Iq directly to pump or to the circuit board in control panel hmmm
The Aqaulink should have a pump setting in the menu.
@@SPL i have no way to program my pumps the aqulink just a control board.
Can anyone tell me what "Unknown Fault" means on a Jandy Pump with Jep-R controller?
Give Jandy a call.
Thank you for this video. You show setting up 2 run times. Can a third run time be used? Possibly using the 3rd and 4th buttons?
Yes. You can progrma those as well
I can’t see how to add the program as the menus is different when I hit menu on button 3 & 4. I don’t see the time on or off option. Any thoughts? I checked the manual but it is not very detailed. Thank you again.
Getting pool re-plastered and have been told to run the pump continuously for 1st 72 hours, is there a way to program that to happen or will that require me to program timers for that initial period and then again after that?
Set the run time from 2:00 pm to 1:59 pm. That will keep it running 23:59. Close enough.
sorry first time pool owner. I have the jandy controller and then two manual yellow dials. the left yellow dial I believe is for the salt and then the second one for the sweeper? I have them set to the same time 8-2 as the jandy controller by following your instructions but I cant set the time as it was already set..it is only 20 min. off but does this made a difference? also the star light is red but it is working/running. shouldn't it be green?
I would call Jandy tech support 800-822-7933
I can't seem to enter the Service Menu. I held down the Menu + 4 button for longer than 10 seconds.
What do you think the issue is?
Not sure. It should work. I think it is time to give Jandy/Fluidra a call:
(800) 822-7933
How can I program a jandy true clear salt system for pump times I want. Bought a house now Pump runs at most expensive time of day.
What is best way to program if these are connected to a separate timer wheel that controls the booster pump
It must be set to at least 2300 RPM and set the booster pump to come on when it is running.
What’s the trick for unlocking the keypad? Keypad is locked and can proceed with settings. Any tips?
Try pressing the up and down buttons at the same time and hold them for 5 seconds. That should unlock it.
How do you just turn the pump off when you need to clean the filter
Hit whichever of the first two buttons to the left is green. When it turns red the pump is off.
Good morning,
It seem I can't adjust my speed on the Estar feature, and I tried holding the arrows, but no luck.
Any recommendations?
Thanks!
I believe the star setting is done in the programming menu. I think I show how to get into that in the video.
Truly appreciate your help!
What is best settings for the RPM's
Star set at 1800 RPM for 8-10 hours, Speed 2 2400 RPM for 4-6 hours
@@SPL doesnt it depend on the size and location of you pool
@@SPL i live in Riverside Ca , is 1800 for 8 -10 hrs a day good for me?
Hey great video. I'm little confused. Is this pump can be schedule for only 2 speeds? For example if I wanna setup 24 hour schedule with 4 different speeds.
Is it possible?
It's an overly complicated controller. I suggest upgrading to the iQpump101 where you can set a number of programs through your phone on the app.
@@SPL thank you
How do fix the lcd display? The light is faded so it makes it difficult to see
Hmm. You may need a new unit at this point.
@@SPL where do I buy one? Can’t seem to find it online? I have an electrician to install
My system always starts with prime mode. Is that normal
Yes.
Our pump says it is self priming. Do I select 0 Min. on the controller? Thanks.
It still needs to go though the 3 minute priming cycle. That just means it will prime even if the pump basket is not full of water after cleaning it.
How do you turn it on and off manually?
You just hit the button that is green -once. That will stop it.
Hey buddy. Need to know where to buy power wire for jep-r any links?
Call Jandy and they will probably send you one at no cost.
Does this remote control the lights of the pool too?
This one no. You would need the Aqualink Z4
How do i reset my Jandy JEP-R Controller?
If you call Jandy while you are at the pool they can walk you through it.
The pad is locked and I can't unlock it. I presses up and down arrow for 5 seconds but nothing. Any ideas?
Could be a bad JEP-R.
@@SPL THANKS!
Do you need overlapping run times?
They don't need to overlap
My kepad isn’t responding and it’s unlocked. What can I do?
It could have gone bad. A known defect after a few years. You may need a new JEP-R
@@SPL turned off the breaker for 5 minutes and it worked
Great Video! A question if you have time to answer me. I am in Portugal and electricity is priced at 3 levels: during the night from 10PM till 8AM it is cheap, 8 till 10:30AM fairly expensive, 10:30AM till 1PM extremely expensive, 1PM till 7:30PM fairly expensive, 7:30 till 9PM extremely expensive, 9 till 10PM fairly expensive and then during the night cheap. I would like the pump to NOT work when it is extremely expensive : 10:30AM till 1PM and 7:30 till 9PM. Will I have to use the 4 program buttons as it is so complicated? Thanks for your help.
The benefit of a VS pump is it shouldn't matter when you run it. At 1800 RPM it is only using 120 watts. So you can run that for 14 hours and it would be equal to 1 hour of a standard pump. Run it at 2400 RPM and it is still only about 450 watts. I would run it at 1800 RPM during the expensive hours and then a good medium speed 2400 RPM the rest of the time. No need to ever run it over 2400 RPMS unless you are heating your pool or possibly using an attached spa.
Swimming Pool Tips, Reviews & How To - SPL thanks so much! Great to get a reply that makes sense and I did not know that at certain speeds it was consuming so little compared to the normal pumps. But since the pool is quiet big and deep (250m3) there are 2 pumps. One VS (600 till 3450RPM) and the other normal which has a constant speed of 2850RPM but from the same brand. Not to tire to much the VS pump I was thinking of following your advice during the day for the VS pump but at night only use the regular pump. Does this make sense to you and do you think it is a good idea?
Also I noticed that the VS pump is preprogrammed with names such as waterfall, cleaner etc... were these preprogrammed for a reason? Do they actually have a specific function?
Many thanks!
And greetings of Portugal
How do I unlock the keypad?? It won’t unlock:(
Sometimes these go bad and the only solution is a new unit. But I would call Jandy Tech support 1st.
Mine says display locked. How do I unlock it?
Hold the up and down at the same time to lock and unlock for about 5 seconds.
Did not show me how to simply turn the motor on and off.
It's pretty simple. Hit one of the first tow buttons. Typically the 2nd one. It will turn green and pump will turn on.
How to I get my ump off locked
hold up/down arrow keys together for 5 seconds
I need to turn off my zodiac controller pum explain me how please
Hit the button 1 or 2 until it is green.
What a pOS controller
So overly complicated. Agreed.
@@SPL I still like the Hayward programming :)
Sigh....
Instead of getting simpler, pool controls are increasingly complicated.
A standard 2 speed pump will do what variable speed pumps are purchased to do, save electricity. They have no electronics to fail and have been on the market for decades.
They run at 1725 rpms and 3450 rpms.
When it comes to the difference in electrical consumption, we're splitting dimes here.
I just moved into a place that has this controller, it's awful. If you press buttons too quickly it freaks out and hard resets itself. Such a pain in the a**
Yes, I have to refer to the quick guide all the time myself. Overengineer at it's worst.
Ok its a little to advanced for a newbie. All I know is there are buttons.
LOL! Some genius designed this. 😂
Is anything user friendly anymore....sheesh
They have a new pump controller that replaces this. Easy as can be. Go to their website.
I hate this controller.
Me too. I have to pull out a cheat sheet whenever I need to mess with one. Way overly complicated.
@@SPL lol David you’re my cheat for this , and I appreciate it
What if it says “keypad locked “ how to unlock??
Hold both up and down arrow keys for 7 seconds
Horrible system.
Overly complicated is how I like to phrase it. But that works too. 👍