speaking as someone fairly new and recently buying a servo tester, ( mine came with no instructions ) .....I would have never thought of plugging the ESC and battery into one of the 3-pin " out " ports.....also , I thought the single 3-pin ( IN ) port marked 4.8 - 6.0 vdc is strictly for powering the tester with a stand alone power supply ( and the voltage match is critical ) .... also thought that all servos and motors need to be connected on a 3-pin connector , marked " OUT " .... thanks
Damn I'm such an idiot. I plugged in my esc to the tester like you did but then my stupid ass plugged in the battery to the other end of the tester and fried the whole damn setup. Ugh! Wish I had seen this sooner
speaking as someone fairly new and also buying a sevo tester, ( mine came with no instructions ) ..I can understand how you did that....I would have never thought of plugging the ESC and battery into one of the " out " ports.....the 4.8 - 6.00 vdc side 3-pin port is strictly for powering the tester with a stand alone power supply...and the voltage match is critical....
@@techysinsight Yes first mod is slowly lose power , second mod is he start with max power and also lose power and third he turn on and of on evry second or two. But it cant hold motor on , constantly for 10 seconds without losing power.
I'm using a 12V car jumper starter battery with usb volt changer/regulator. You can use any battery really. I use the motor as a rotary cutter/drill/sander.
My motor is no working with servo tester,,,only beeping one times,,and motor start vibrating on increasing power....pls help me....is there any solution
@@techysinsight I have done both things,,charged full battery ,and also check minimum position of servo,,,,but when I connect power, servo beeps only once ,,and on increasing servo power,,,motor start vibrating (not rotating)....
![[UNCUT]"เศรษฐา" โดนบีบให้ลาออก เผยดีลลับ "ทักษิณ" ต้องต่อโปร ไม่งั้นเจอจุดจบ! I คนดังนั่งเคลียร์](http://i.ytimg.com/vi/XlH3k81dxmE/mqdefault.jpg)
th-cam.com/video/gilD9NsoU3I/w-d-xo.html
Making mini drill using the same setup
Thank you helped so much 😀👏👏
Watched from USSR and it was a good explanation!
Hi, there !!! Nice video , nice work , keep working and keep posting new videos !!!!
Thanks for posting.
I'm thinking of using this to control the speed of the escooter motor. Plugging the cable from the trigger to the tester then to the esc.
speaking as someone fairly new and recently buying a servo tester, ( mine came with no instructions ) .....I would have never thought of plugging the ESC and battery into one of the 3-pin " out " ports.....also , I thought the single 3-pin ( IN ) port marked 4.8 - 6.0 vdc is strictly for powering the tester with a stand alone power supply ( and the voltage match is critical ) .... also thought that all servos and motors need to be connected on a 3-pin connector , marked " OUT " .... thanks
Damn I'm such an idiot. I plugged in my esc to the tester like you did but then my stupid ass plugged in the battery to the other end of the tester and fried the whole damn setup. Ugh! Wish I had seen this sooner
speaking as someone fairly new and also buying a sevo tester, ( mine came with no instructions ) ..I can understand how you did that....I would have never thought of plugging the ESC and battery into one of the " out " ports.....the 4.8 - 6.00 vdc side 3-pin port is strictly for powering the tester with a stand alone power supply...and the voltage match is critical....
Is there a way to do this with an ESC without a BEC?
very hepful for me today
Hello sir I had doubt regarding this bldc motor....i.e just we need the battery,motor,esc and servo tester
These are enough to run a motor right....
Yes
When I connect my servo to tester all the lights glows up & servo begins to rotate randomly
Is there any solution?
is it after using servo testing, esc is calibrated again with RX TX?
No there is no such thing
Servo tester is a setup without tx
My brushless motor not run...its sound like beeping beeping not run I am using a servo tester....3500kv with 40a ESC
Check with a different motor to verify whether the servo tester is ok
This happend to me when my servo tester went faulty
hi
Why moror can works only few seconds and than he stops until I again restart proces(by rotating taster)?Can it somehow work without break?
There are 3 modes in the servo tester press the button to change
It also happens when your battery has less power
@@techysinsight Yes first mod is slowly lose power , second mod is he start with max power and also lose power and third he turn on and of on evry second or two. But it cant hold motor on , constantly for 10 seconds without losing power.
I have strong battery , but even if i use first mod and tune it to go slow and use less energy motor stops after few seconds.
Ok can check with a different esc
Can I use a 12V 30Amps SMPS instead of the Battery?
Yes you can
Can use laptop charger
Yes
I'm using a 12V car jumper starter battery with usb volt changer/regulator. You can use any battery really. I use the motor as a rotary cutter/drill/sander.
can I run stepper motor 6 pole
Hopefully yes
You can test servo motors with this .since I don't have a stepper motor I personally have not tested yet.
Agar mai is esc me 2700kv ka brushless motor laga dunga to kuch problem nhi hoga na?
Nahi
@@techysinsight thank you
Kya 2700kv ka brushless motor isse bhi speed chalega?
2700kv ka brushless motor 30A ke kisi bhi esc me laga sakte hai kya?
You can use any 30 amp esc available
My motor is no working with servo tester,,,only beeping one times,,and motor start vibrating on increasing power....pls help me....is there any solution
Check the soldering
And it happens when the battery is underpowered or faulty
Also maintain minimum position in the servo tester before atart
@@techysinsight I have done both things,,charged full battery ,and also check minimum position of servo,,,,but when I connect power, servo beeps only once ,,and on increasing servo power,,,motor start vibrating (not rotating)....
Then may b the motor is faulty
@@techysinsight thank you techys insight for your advice and help
Are you experiencing malnutrition ?...cant hear/understand anything you saying
I can understand it all clearly and I'm 68