Just installed this today... works great ! I have a 2015 double cab Tacoma. Wiring was easy and install went smooth. Blue wire goes to blue/black and Green goes to blue/red. I have one comment on this video though, I would suggest not running the wires the way he did. If the zip ties break your wire is going to hang low and possibly get damaged. I followed the existing wire runs closer to the body of the truck. If you use a basic fish tape to get over the gas tank you can be done in less than 2 min. I also brought my wire in under the driver seat through an existing grommet, use a coat hanger or in my case a 14 gage ground wire i found in my garage to feed the wire through. you are going to need to unravel the water resistant tape, but other than that nothing too crazy HOPE THIS HELPS GUYS !
Did this on my 2009 Tacoma. Worked great, just make sure when your are running the harness through the engine compartment you run it UNDER all the other wires and components, otherwise you might end up having to pull it out of the cab to re-run it, not that I did that....Great tutorial!
Just installed yesterday! Now the bed is useful space. Only thing is I forgot to put the plastic bed liner on before I bolted it down and made twice as much work for myself. But who cares i had fun.
Just did this on my 2015 Tacoma trd sport, works like advertised. The metal arm and bracket that the solenoid pushes squeaks a bit, probably would’ve been ideal for them to be made out of brass rather than stainless.. figuring that it’ll wear down a bit over time and hopefully make the squeak stop. If not I’ll pop the tailgate open again some day and maybe put some Teflon in the spots it’s squeaking , idk 🤷♂️
Blue to blue black for me. Also, had to go through the grommet under the drivers floorboard because the provided wire wasn’t long enough to reach from the wiring harness at the fire wall. If anyone ever cares to splice like.. 2 more feet to the wire, you could go through a hole that’s a few inches above the wire harness grommet , slightly behind the brake booster that isn’t occupied, just gotta poke a hole into the thin carpet, drill a hole in the small plastic grommet. That’s what I wanted to do but didn’t have enough wire length to reach. Also debating looking into finding a completely different solenoid to upgrade with, for now I’ll see how this one lasts.
Thanks very much for the detailed instructions. 10/12/2014 - Just finished installing this. Had to make the drain hole larger and I ran the cable to the passenger side. Thanks for the video.
Thanks for the video! One note - I was terrified of breaking the plastic connector for the rod in the tailgate (done it before in another vehicle). I simply used a ratcheted box wrench to remove and install that 10MM bolt. That way I didn't need to remove the rod.
Good info; however, without knowing if the 2015 color code is the same, I might wind up splicing into something unintended and have the Tacoma drive down the road rather than just lock and unlock the door/tailgate. Thanks in advance.
Couldn't a thief disconnect the coupling at 2:46 and then use a battery and/or jumper of some kind to open the lock? I mean it's just exposed down there. Can you pull it back into the tailgate after you have it connected?
Just installed the PL8525 on a 2013 Access cab Tacoma. Lots of blue wires but none with black or red stripes. Anyone else had this issue or have a solution?
Quick Question if i run it along the frame and up onto the engine compartment why would turn around and run it back wouldd't you just run it to where it needs to go?
It should be be the Tan with a Yellow Stripe wire and the grey wire. Here is a link to the instructions, also if you have any questions you can reach Pop & Lock at 800-342-5911. www.popandlock.net/download/PL8140.pdf.87cd2dd5f95d62d2eb1387fcb7bb9436
Step 8 of the install instructions go over the 2 door and access cab options. Here is a link to view the install instructions. www.popandlock.net/download/PL8521.pdf.8efb49664f8910a2c0bf9105312b2ae0
my 2015 access cab trd off road does not have a blue/red and blue/black...i did the rest of the install but had to leave the wire i pulled from the tailgate couiled up under the carpet. Very unimpressed with the "instructions" provided by pop and lock. I would never recommend their product based on how poor they are but they seem to be the only one manufacturing these locks.
Just installed this today... works great ! I have a 2015 double cab Tacoma. Wiring was easy and install went smooth. Blue wire goes to blue/black and Green goes to blue/red. I have one comment on this video though, I would suggest not running the wires the way he did. If the zip ties break your wire is going to hang low and possibly get damaged. I followed the existing wire runs closer to the body of the truck. If you use a basic fish tape to get over the gas tank you can be done in less than 2 min.
I also brought my wire in under the driver seat through an existing grommet, use a coat hanger or in my case a 14 gage ground wire i found in my garage to feed the wire through. you are going to need to unravel the water resistant tape, but other than that nothing too crazy
HOPE THIS HELPS GUYS !
This is the best version online, I wish this would have shown up in the search first. Appreciate your assistance.
Did this on my 2009 Tacoma. Worked great, just make sure when your are running the harness through the engine compartment you run it UNDER all the other wires and components, otherwise you might end up having to pull it out of the cab to re-run it, not that I did that....Great tutorial!
GREAT supplement to the very sketchy instructions that come with the Pop & Lock. Got mine successfully and neatly installed in about 2 hours.
@1:50. I had to use my grinder on the bracket to make it sit flush with the surface of the tailgate. Great product. Works quite good.
Just installed yesterday! Now the bed is useful space. Only thing is I forgot to put the plastic bed liner on before I bolted it down and made twice as much work for myself. But who cares i had fun.
Just did this on my 2015 Tacoma trd sport, works like advertised. The metal arm and bracket that the solenoid pushes squeaks a bit, probably would’ve been ideal for them to be made out of brass rather than stainless.. figuring that it’ll wear down a bit over time and hopefully make the squeak stop. If not I’ll pop the tailgate open again some day and maybe put some Teflon in the spots it’s squeaking , idk 🤷♂️
Blue to blue black for me. Also, had to go through the grommet under the drivers floorboard because the provided wire wasn’t long enough to reach from the wiring harness at the fire wall. If anyone ever cares to splice like.. 2 more feet to the wire, you could go through a hole that’s a few inches above the wire harness grommet , slightly behind the brake booster that isn’t occupied, just gotta poke a hole into the thin carpet, drill a hole in the small plastic grommet. That’s what I wanted to do but didn’t have enough wire length to reach.
Also debating looking into finding a completely different solenoid to upgrade with, for now I’ll see how this one lasts.
Great video !!!! Took only 1 hr to install thanks to your video !!!!
Thanks very much for the detailed instructions.
10/12/2014 - Just finished installing this. Had to make the drain hole larger and I ran the cable to the passenger side. Thanks for the video.
Thanks for the video! One note - I was terrified of breaking the plastic connector for the rod in the tailgate (done it before in another vehicle). I simply used a ratcheted box wrench to remove and install that 10MM bolt. That way I didn't need to remove the rod.
If you take the drivers seat out, you can go up through the rubber grommet located underneath the seat.
Great tip Jamie! We will try that out!
thank you. this worked for me.
Thanks for this great vid. Looks easy enough for me to install myself.
If I have a Viper alarm system on my 2015 Tacoma, is it the same process to install the power tail gate lock?
What splicers did you use for the wires?
Good info; however, without knowing if the 2015 color code is the same, I might wind up splicing into something unintended and have the Tacoma drive down the road rather than just lock and unlock the door/tailgate. Thanks in advance.
One question, I want to connect to the passengers side (double click open), which wires 2009 Tacoma.
Couldn't a thief disconnect the coupling at 2:46 and then use a battery and/or jumper of some kind to open the lock? I mean it's just exposed down there. Can you pull it back into the tailgate after you have it connected?
Please make one for the 2016 Tacoma (PL 8535).
Does anyone know the color wires to splice into for a 2015 access cab tacoma?
+Ken C. It should be the same colors. If you are having issues give our tech support line a call with your order number at 18888554621!
Did this to my 2016 , anyway to just put a switch inside the cab to control the lock? I'd hate the lock being used 30 times a day with my job.
If I add this to my truck and some how that lock motor fails in the lock position with a bed cover on and locked what will I do?
I contacted Pop & Lock and they told me unless you have key access on you tailgate there is no way to unlock the tailgate.
rustler1982 It's is possible. It happened to me. I'll make a video soon on how to do so.
I installed their key handle works with the ignition key no wires easy ten minutes later done.
Me too. Does anyone know if the wiring color code mentioned here is the same as the 2015??
do you know if the wiring is the same for a 2015 Tacoma?
my 2013 does not have the center collum so where do i make my connection?
will this work for 2015 tacomas?
Is this video missing a step? It goes from connecting beneath the tailgate, to punching through the firewall. What are we doing in the engine bay?
Can anyone provide wire coding colors for a 2014 Tacoma crew cab? Thx in advance.
Do you happen to have the part number for your Pop & Lock? This will help us make sure we are giving you the correct information.
Just installed the PL8525 on a 2013 Access cab Tacoma. Lots of blue wires but none with black or red stripes. Anyone else had this issue or have a solution?
yeah but how secure is it realy ?
Quick Question if i run it along the frame and up onto the engine compartment why would turn around and run it back wouldd't you just run it to where it needs to go?
There is a grommet under the driver side by the B pillar to go up.
I have a 2015 double cab and I don't see blue/black wire. Is it just the solid black to the blue that I ran from the tail gate
It should be be the Tan with a Yellow Stripe wire and the grey wire. Here is a link to the instructions, also if you have any questions you can reach Pop & Lock at 800-342-5911. www.popandlock.net/download/PL8140.pdf.87cd2dd5f95d62d2eb1387fcb7bb9436
How would I do this on an Access Cab truck? The B pillar is on the rear door instead of fixed....
Step 8 of the install instructions go over the 2 door and access cab options. Here is a link to view the install instructions.
www.popandlock.net/download/PL8521.pdf.8efb49664f8910a2c0bf9105312b2ae0
Curious what your shop charges to install this kit.
We don't have a shop for installations however if you want professional assistance - you can call in and get our tech support line! 877-216-5446
Does this work with the 2014 double cab?
We do have the option available for that vehicle. If you'd like to get one ordered give us a call at 888-855-4621.
if the tailgate is closed and you lock it and the motor fails to unlock it how do you get it open.
Your key still works like normal.
my 2015 access cab trd off road does not have a blue/red and blue/black...i did the rest of the install but had to leave the wire i pulled from the tailgate couiled up under the carpet. Very unimpressed with the "instructions" provided by pop and lock. I would never recommend their product based on how poor they are but they seem to be the only one manufacturing these locks.
Doesn't work for a 2011 those color wires don't exist