LIFT-502 RHOX BMF 7” A-Arm Lift Kit on an Electric E-Z-Go TXT
ฝัง
- เผยแพร่เมื่อ 27 ก.ค. 2024
- Installation instructions for the RHOX BMF 7" A-Arm Lift Kit (LIFT-502) on an Electric E-Z-Go TXT.
Installation Note: When installing the steering rack, the pin to attach it to the rack to the steering column should be on the driver side. - ยานยนต์และพาหนะ
I wish there was a walkaround the cart after it was all finished
We started doing that in some of our videos. I'll pass that along to our crew. Thanks Kurt!
Great video I recommend hitting it with a little rinse job so you not all dirty the whole time you work.
We agree! :)
Do I need a special tool to turn the shocks? The eye hole at the bottom needs to be turned about 90 degrees on one and 45 on the other to line up with the mounting bracket/bolts
Yes, a spanner wrench will help with that.
What rim and tire combo did you guys use for the video?
The wheel is our TIR-RX283-B (12x7", ET-25) and the tire is our TIR-361 (25x10-12, 6-ply).
How long are the included shocks? And are the shocks included adjustable?
I do not have a spare shock to measure off the cart, but the one installed is 16.5" CTC of the mounting holes while under load. The spring is adjustable but not the shock itself.
I was curious where the allen head type bolts go?
They are for the steering box assembly. Thank you for asking.
Do you make an adapter that would allow it to fit to the pre-2001.5 TXT's at the steering column? Anything else that is substantially different in the carts that would make this lift not fit?
No, we do not offer an adapter. The spindles are also different.
@@GolfCartInstructions Thanks for the reply. Near as I can tell, you don't make a long travel lift for these earlier carts, correct? 1994-2001.5?
What are the measurements for the recommended camber setting?
A positive camber is recommended, meaning you will want the top of the tires to stick out farther away from the cart than the bottom of the tires. This way when a load is applied, the camber will even out so the wheels ride straight. We cannot provide an exact measurement because there are too many variables at play (cart, load size, state of suspension, tires etc.). As long as the tires and wheels are straight with the load you will be good. Then you will want to check for tire wear to make sure it is riding evenly over time. If not, you can readjust your alignment.
This is a very nice looking lift kit but 7 is a little high as it wont fit in my garage. Do ya'll carry this lift in a 6inch?
Thank you! We carry a 6" spindle lift (LIFT-102) and a 5" drop axle (LIFT-108). These match the same year range as the LIFT-502 and can be seen at www.rhox.com. Just type the part number in the search field.
Will this fit the 1994.5 Medalist Dan please let me know Thanks
It should fit a Medalist.
Does RHOX has tech support? My steering will not hang down enough to bolt into the spindles. They are welded probably 1.5" lower than the ones in this video.
Hi Brad, You have the correct spindles. The video was shot with the first generation of these lift kits. We modified the spindles to provide more stability. Some find it easier to mount the tie rod ends to the spindles with the assembly on the bench. You can also mount these when the car is on the ground. Another solution would be to use a jack under the A-arm. It can be done.
@@GolfCartInstructions do you have an email? The tie rods will not reach down close to enough to even get into the hole let alone bolt them down. Pulled all the way down they still need to go down well over an inch. Please call me 425-891-2373
Should there be play at the lower a-arm where it connects to the spindle? I have this kit on my ezgo and there's in and out play on both sides. I'm thinking the bushing are wore out. Thanks.
It sounds like bushings.
@@GolfCartInstructions could I order them thru yall or do I have to go thru a dealer. It's a ez-go with the 13.5 kawasaki motor.
@@kevinwatsin5700 We don't have a kit available yet complete with bushings and the spacer. The bushings are found in LIFT-103-B. They are not green. The metal spacers are specific to that lift kit. You may be okay reusing your spacer if it is still in good shape. LIFT-103-B can be purchased through a RHOX authorized dealer. If you submit a contact us form on RHOX.com, we can send you a list of dealers in your area or some web dealers.
What size tires were used
Sorry Brian, I just saw this - The wheel is our TIR-RX283-B (12x7", ET-25) and the tire is our TIR-361 (25x10-12, 6-ply).
Is there a torque spec on the lower nut on the front spindles? My cart is about 4 years old and they have worked loose. Just wanna make sure I don't overtighten the nuts. Thank you.
I am checking with our factory because this is tightened at the manufacturing level. Once I hear back, I will let you know.
Thank you for your patience. The kingpin bolt should be torqued to 90NM which is around 66.38 ft lbs.
@@GolfCartInstructions thank u. I was close. Had it at 55 ft pounds. Again thank u for your help.
(2003 EZGO TXT electric) I switched to 8" wheels and 22" tires for the smoother ride. I have 1" wheel spacers as well. I saw a description say this lift requires 12" wheels. Does that still apply with spacers?
We have not tried it with spacers. We run rims with a -1" offset in general with lift kits. When we tested this, I believe the 10" rims interfered front suspension, even with the 1" offset. You can always try it and see if it works. You want the tires and wheels to turn freely without anything impeding their path of travel or rubbing.
@@GolfCartInstructions Thank you for responding. I'll have to do some more research before I spend the money and possibly not be able to use the tires/wheels I have.
@@SJS-Outdoors I completely understand. Chances are, you will probably want to upgrade to the 12".
@@GolfCartInstructions What's ironic about that is that my cart came with 14" wheels and 23" tires. I swapped for more cushion!. DOH!
@@SJS-Outdoors That's how it always works! :)
Can you recommend a shock replacement for this kit? Or what is the type/size/model of the ones that come with the kit ?
We do not offer replacement shocks for this kit at this time.
@@GolfCartInstructions can you recommend a compatible shocks?
@@JoseLuisZapata We do not offer any that would work with it. Do you need replacement shocks?
@@GolfCartInstructions Anyone who buys this lift needs different shocks. The ones you supply are to damn stiff, so much money for trash! You can't even ride in the cart, ZERO suspension travel.....
@@tnet6969 Thank you for your feedback. The shocks can be slightly adjusted with a spanner wrench. They will also soften once broken in. Keep in mind, they are heavy duty so they will be on the stiffer side compared to factory.
No stronger back leaf springs or shocks?
They would be sold separately and are not included in the lift kit.
Is this kit still available? I can't find anywhere for sale anymore.
This kit has been discontinued and has been superseded by LIFT-514. If you need it to fit a gas TXT 01.5-08.5, you can purchase this and LIFT-502R. That will give you the correct lift blocks for that year range of gas carts.
Do they make a lift kit for a 2five lsv?
We do not make them for a 2five. Thank you for asking.
Will this kit bolt up to a 1993 ezgo txt?
I believe I just emailed you back via our RHOX website. We will need to know your cart's serial number as E-Z-Go didn't make a TXT in 93. Please respond to the email as that is monitored more often.
Will it fit a 26” tire?
The largest we have tried is a 25" tire, but it did have room. The only reason we didn't try anything larger was because we didn't carry any at that time. It's possible the 26" will fit.
You said passenger. But installed it on the driver side.
In the video (6:10) he says to install the steering rack with the pin to the steering column is in the passenger side. This is wrong. Should be on the driver side
You're correct. Thank you for point that out.
How long did this take from start to finish
We can install this in about 45 minutes if all of our tools are in reach and there is nothing wrong with the cart. The front will be faster than the rear.
can you install a front hitch with this lift?
Has anyone installed this kit on a early model ezgo txt gas?? I have a 1997 unit???
We have not tried it. The spindles are different so you will need new hubs. I'm not sure how the rest of the front end compares. I believe it is the same but you would have to compare the parts between manuals to be certain.
I am going to try it when it comes back in stock
@@94auwing Let us know how it works!
@@GolfCartInstructions I sure will once I get the kit.
Link?
What link are you looking for?
LINK
?
Do you make a front disc brake kit
No, only rear.
@@GolfCartInstructions well that stinks maybe I can put jakes front spindles on your front end. Does your kit use stock spindles?
Never mind I see it does not I will need to fab a mount
@@94auwing No, that will not work.
I love your front end but I need front disc brakes
Spindles backwards.
Not in the video . . .
Please help, my long travel RHOX front steering rods are adjusted almost all the way out (over an inch of threads are showing) is that safe? Is that normal?
commandyne at gmail com