Nice work on the units, very impressive. Another way to do this would be to use approximately 1/16" thick x 2 1/8" wide solid wood for the edging on all the plywood units. This would show less edge grain on the shelves and sides and allow the overhang to simply be sanded off and avoid the routing process altogether. The plywood would have to be glued together with spacers going the length of the sides and shelves however as the 1/16" veneer would need backing for strength. These units would get put together first without the veneer and then ripped to the correct width first to allow the edges to be perfectly square and straight. Pieces can then be be glued and clamped together with the veneer two units at a time with the veneers facing each other. I use some sort of cushion between the veneer strips to provide even pressure on the veneers and keep any excess glue squeeze out from sticking the veneers to each other. I feel anytime you can reduce the thickness of an edging or faceframe, you reduce the chances of sanding (or routing) through the often too thin veneer on plywood.
Only 15 so it’s amazing. My dad built homes sir probably 50 yrs. I showed him a Spencer stair video one day & he watched intently. Then he commented that’s the guy you hire, give him the plans , take all his phone calls , then leave him alone? He will make both him & I money !
Love to see a video of the poor chap painting the backs of the cabinets. Spencer I would love to see you set up a finishing department with all the space you have . We finish most everything before we fabricate. The finished product is what your judged on. Love seeing your business grow .
I thought the same thing......oof what a pain in the arse to tape off that stain grade oak. It makes me think it would have been better to prime and paint that back panel once before he stapled them on. But, like he said, that's not his problem...it's the painter's problem.
Typical shortsighted crap that you see on so many jobs: "not my problem." No way will that paint job be as good as if it were done PRIOR to the back panel installation. A better way would be to coordinate with the painter. Or, for god's sake, just roll the paint yourself! There was a time when a carpenter would pick up a paint brush or roller.
When I was active and had my own shop I was building projects like this and furniture. Since my wife passed away I sold our house and my shop and it never got back up and running again. Just took the life out of me. I like to think I was on your level on projects such as this. Love to see someone else that lives their work like you do Spencer. Look forward to your next video as always.
Sorry to hear about the loss of your wife. There are absences that are beyond filling. Given your evident continued interest, perhaps there's a way for you to rejoin this part of yourself, maybe through teaching or some appropriate volunteer activity, to pass along your hard-earned knowledge and passion for the craft. Many could benefit from all you have to offer.
Great video! I believe that the 23 gauge, as well as 21 and 18 have a chisel point. This means that when you are firing oins,with these smaller gauges, you should be holding the gun perpendicular' not parallel. This way, the pin will deflect to the right or left, rather than the fron or back. however, with the larger 15, and 16s, the chisel is cut the other way. and should be nailed with the gun parallel. The pins on the 23 are so small that it may not matter, but this is a good rule of thumb. I hope this is helpful. I am a retired furniture maker of 35 plus years, and am still learning. I have gained a lot of new ideas from you and enjoy very much your superb content! thanks.
Im a electrical contractor by trade for about 30 years but have done alot of wood work also. Man would love to work with my guy here for about a year, to have the opportunity to learn from a true master of wood working. Outstanding quality work!
Can’t thank you enough for all this content that you put out. I am a remodeler by trade, but fine woodwork and trim carpentry is my passion. The amount of knowledge I’ve gained by watching your videos is immeasurable. Keep up the great work! Would love to take the leap and transfer to what you do, as you know, it’s not an easy step.
It is really nice to watch a video that is put out on TH-cam for informative reasons rather than entertainment. I am so tired of watching people that think that they are entertaining, but have no substance to what they’re talking about. Not only are you extremely informative and painstakingly detailed about how and why you do everything that you do but you are also entertaining at the same time because of the detail and the information that you convey. Keep up the good work. I have always enjoyed watching your videos.
Man buddy u hit the nail on thee head! I am always trying to learn! Bottom line I want to reduce the number of clients I hv to those who are aware of prices however; will pay your price w/ o haggling ! That means I hv to execute precisely in my carpentry builds! Listening to music, 10 x speed ( while they work thru what seems to them to be boring) and I am screaming nooooo I need to see how you executed that joint ! I am done I cancel and move on! I even spend hours watching framing so if a customer states I hv this issue I understand and can refer them to the right framer, roofer, ect.,. In order to be competent; passion is a huge part of it! Bout 3/4 years ago I clicked on Spencer and I found that teacher! Great resource!
very informative as always. spencer gives us for free a master class in so many aspects of carpentry and he never stops learning as we do as builders. love it! also the comprehensive breakdowns on tool set ups and case use is unrivaled. thank you!
Class A work from start to finish, and lots of good tips and advice. The painters should have stepped forward and painted the plywood back before you stapled it in place, but that’s their problem. Thank you for all the effort you put into this video.
If the bookcases were done the way the designer wanted, the field finish by the painter would have been stain and finish, then paint the back (drywall). Shop paint of the back before assembly would, still require repainting on site. If this is the look the designer wanted, and the white oak was not shop finished then practically speaking there is no benefit in applying paint if stain and finish is also not shop applied. Sometimes best method has to stand behind design whims. We could argue that wanting painted drywall as a back to the bookcases is why designers are designers. Give people what they want even when you educate them on best practice and they still want something else. Possibly the designer will learn something from this project. Many designers and some architects want a specific unconventional result but maybe it’s our job to tell them how to get there. Placing a back on these bookcases when open back was the design intent…is a good example of this.
@@henrypeisch5289 I have to wonder how much thought the designer gave to this small detail of the project. To my mind placing bookcases with open backs against drywall is a non-starter for all the reasons Spencer noted. Besides, can anyone tell the difference between painted drywall and a suitably finished backer? I doubt it, especially with the bookcases full of books or whatever. Furthermore, the backer can probably take more of a hit than drywall. The owner is fortunate to have Spencer on the job.
@@theodoreshasta7846 it’s often about creating a unique design. Maybe the wall paint will be used on the 1/4” ply back. Same look as drywall. Our challenge is to work with the designer. If we need a disclaimer with a design (like installing horizontal balusters over an open to below floor space) we probably should pass on that aspect of the project. It is a goal to eventually understand as many aspects of the building process as possible so we can guide the design process without saying “no”. But there are times to say no anyway. I have always believed that licensed architects should be required to spend at least 2 years in the trades before certification. Maybe the same should apply to interior design professionals.
I am a finish carpenter and have done so for the last 15 yrs. For people who don't know the inner workings of running trim and doing built ins etc, He is the real deal. It's not often you see someone who delivers such high end results consistently in every aspect of his jobs. The customers are getting their money's worth without a doubt. Even us experienced carpenters learn new techniques/efficiency from watching this channel. Keep up the good work man. You have a awesome thing going and I have nothing but respect for you and what you do.. to many more years from Woodstock Ga. 👍👍💪
I guess I started at a company that did this stuff, so I really don't know any other way to do it. The houses look similar to the ones we do. Mr. Lewis is definitely high level, luckily I worked in a shop full of him, and I was the guy who was a master at looking stupid.
I really like watching your videos. I learn so much from watching them. I am a hobbyist but you have helped me improve the quality of my work so much. Thanks for what you do and keep it up.
Spencer your videos in my opinion are the best thing to watch on TV. Keep up the good work. Next to Norm your videos are the best. This may be your most informative and fun videos you’ve made yet!
I appreciate your response I really do. I’m putting drawer faces on at the moment. Got a walk thru tomorrow. Man I know you hear this a lot but I really find your channel a breath of fresh air. You are the real deal and I relate 100%. Thank you for the tip. God bless.
You are a wonderful craftsman. I’ve been in the cabinet business for over 30 years. I know quality and you have it. The castle machine is the best money can buy
The blade with the high tooth count is a must for cross-cutting but I would still highly recommend a crosscut sled. The zero clearance with a sled really makes a huge difference as your material has virtually no chance of tearing out on the underside. Great work and awesome in depth video!
Spencer, love your videos, brother. I hope you’ll take this in the way that I mean it. Speaking for every woodworker who’s NOT in the trades, it does my heart good to hear someone like you say they’ve screwed up countless built-ins. It’s the feeling every hack golfer gets when they watch Tiger shank one into the woods. Thanks for the honesty!
For such high quality work and expertly detailed video’s you deserve waaay more views. This stuff so much better than your next epoxy river table video. 👍
Correction at 5:30 You have a *convex* bit to make a *concave* edge on the plywood. Aside from that, I’ve got nothing to add to your great work except to always say, “amazing work, Spencer!”
Nice work Spencer! After 30+ years of carpentry, I'm always learning from you. This was a fun one. You could still make this a free standing unit by adding panels to the outside. Something I might add to your shelves is to do them like floating shelves. Take two of the spacers and attach ithem to the insides of the box for each shelf. Would have been nice to paint that back panel before attaching, oh well. Many Thanks!
When I come across a channel like this, with a guy who does such a great job and gives people so many detailed and valuable explanations about how to do things the best way, I can definitely not leave without subscribing. Thank you for sharing your experience.
😊Hey there. You are absolutely amazing. You have the right tools, great shop and skills to get it done. You have patience and ability. I commend you. Thanks for sharing the videos. Philip 👊🏼
I have a tip to prevent blowouts when nailing, so that I almost never get blowouts if I'm careful. I relates to the chisel tip on the nails and the orientation of the gun. You only get blowouts to the left or right of the gun, but never up or down, because the bevel on the nail point can guide the nail along the wood grain. Try it out! Thanks for another great video.
Dude. Perfect timing. I don’t know how or why but you always post a zinger like this whenever I come up against a new challenge. Thankful beyond words.
Brilliant - thanks so much for taking the time to produce these videos. What I aspire to mostly is the level of calm you bring to your workplace. I run around like a blue arse fly then wonder where the day has gone !
Surprised not to see clamps on the back edges at the filler strips to pull them together. Must be nice to work with flat plywood ! Another awesome video. Thank you and more like this please.
I so appreciate this type of video - detailed enough to really be useful, not just edited for length. And its really all about the planning and strategy separating work that is 'good enough' from...well, pretty fabulous. I hope your clients appreicate you!
This vid was a banger. I love these long form carpentry videos. So many small expert tips that add up to an incredibly professional result. I am a huge fan of the design also (except the drywall backer idea, lol). Expertly executed, Spencer. 👍 👌
Not making this up......as soon as the flooring is down and I run the base in my current job, I'm building two bookcases to fit in the cavities either side of their fireplace. Timing is everything! Thanks, Spencer!👍
I love how you teach. You are so specific on the details even while knowing your videos are a blend of how to and just trade enjoyment from how to place your wood to be cut to not tearout or over build to cut down. I feel like an apprentice of yours. I do feel a bit let down seeing the gaps and the top trim board installed at the home. I would have really appreciated your few extra minutes of time to at least explain how you were going to fill gaps and finish the install if you didn’t have to do the remainder of the filming. Bravo buddy you are still my favorite trim you tuber. Thanks for challenging me to be the best at all my skills with your level of detail.
Wow man. You are a busy guy. I never expected you to respond. That makes sense. That’s for pointing this out. I’m building some simple one now, nothing like yours. My brick is already there so I’ll probably need shoe or quarter on mine. Thank for the video.
Thank you for this detailed video ! Been watcing you for a couple years now and gotta say youre one of my top favorites to watch and i try to watch your videos as soon as they come out. As always top notch work and outstanding results. Cant wait to see more!
I built one of these for my house early last year. I learned a lot of the stuff you laid out here the hard way. I wish you made this a year earlier but good one.
Other than some adjacent base trim at the drywall, it’s trimmed. Scribed to drywall and a short piece of white oak added at the soffit and paint grade base inside at the back panel. Thin brick will bury the stiles closest to the fireplace. Let’s hope the mason or tile guy masks off well and with clean hands.
In my day here in the southeast, the expectation was that the work would be scribed to the drywall. In those cases, shelves were usually adjustable with a single fixed shelf in the center. (Aesthetics on shelf nosings flush with the frame weren't crucial, and weight would be less). An oversize face frame would be scribed onsite and attached with the case pulled out, so glue could be applied and pocket screws could be attached. Once the FF was done, the piece would be slid back into the opening and would fit like a glove. The alternative method would use either fillers or 2-pc framing to butt the drywall.. You end up with a finished look, but the only aspect you have to sweat is scribing face frames or fillers. Dimensions on the case weren't critical. In my experience, designers always over-specify and obsess about details the average homeowner would never notice or appreciate - often driving up costs without benefit. Your 2" fixed, flush shelves being an example.
@@landonedwards7504 it might be preferred to have a designer helping the client to spend money. Higher margins maybe. We always loved them for that reason. Build in a line item for “conferences” though. Often you will have to tactfully educate a designer about best methods - in the presence of the client and this requires skill and patience. We have done it the same as you describe but attach the face frame prior to scribe. In this case with the video, with thin brick and grouted mortar joints, I would have done these cases the same with only slight structural improvements on the build. A scribe to masonry is always fun and an opportunity to show your skills but in this case, I would let the brick meet the stile - as was done in the video. The only concern is staining the raw oak with thinset or similar mortar. I believe the stile meeting drywall was scribed however. Keep watching.
Thanks Spencer for showing us how it’s done. Great reminders at all key steps. This video is a real confidence-builder for a project that can be a little intimidating. That Castle machine is sweet! Someday. I’m also a big believer in “idiot” marks, especially for built-ins. I tried using a Pentel Hi Polymer Block Eraser to take off pencil lines. They have worked well for me. Amazon sells them, in bulk if you use them a lot (like I do). Erasing with the grain usually takes the marks off completely, or at least close enough. Sometime you need to sand the area (w/ 180 or 220j - lightly, by hand - if the surface will be stained or clear-coated. This has worked for me to eliminate all eraser debris. I agree that a stapler is The tool for back panels. Really hold tight. It’ll stay on there nice & tight - even when you’re moving it into place. Thanks again for all of the time to take to make us better, and yes, please make more project videos. They really help.
Thanks for walking us through the details of your thought process for each step. I learned so much more that way than I would have from a simple “do this” video. It really helps me as I think about how to approach a given project.
My lord that clamp rack should come with an 18+ rating haha! Excellent video and content, as ever. Many thanks for your ongoing effort to educate us all.
I know the table saw is king but you really should think about investing in a high grade panel saw. I work for a cabinet shop in Massachusetts, the owner purchased one a few years back. It is an absolute game changer. Anways always a pleasure watching your content!
I really like your reasoning for making them bigger and then cutting down, I would not have thought about that. I have some 'chunky' shelves in my future and this is a great video to flag for rewatching.
Well, I wasn't expecting a master class in built-in shelves. Great detailed video. All the stuff and none of the fluff. Definitely a subscriber now. Thnaks!
Love your videos. I was wondering if you would possibly do a video showing how you use sketch up. I’ve seen that people have different ways of using it and would love to see how a professional carpenter goes about it. Beautiful work!
Beautiful!! You just can’t beat white oak!! Great Craftsmanship Spencer, love all of your videos. Very informative and inspiring!! Have a Great New Year’s….
I understand that methods and attention to detail matter, but as a newbie I wonder how much of building is just doing the work and earning the experience? I really enjoy watching masters do the work. There’s something truly beautiful about watching something done right.
@28:ish I had a close call with kickback recently, so that cut-to-width sequence scared me... Love your content-- nice to see a creator/ builder with confidence real-world experience
THANKS FOR YOUR SUPPORT!!!
Freud LU80R010: 10" Ultimate Plywood & Melamine Blade - amzn.to/3TPh66h
Collins Tool Co Plywood Prep Router Bit - amzn.to/47qJWgD
Castle TSM22 Pocket Hole Machine - castleusa.com/products/tsm-22-pocket-cutter-machine.html
Bessey K-Body Clamps - amzn.to/48E2Kd9
FastCap Glu-Bot Woodworkers Glue Bottle - amzn.to/3HdjzQg
Festool ETS EC 150/5 Sander - amzn.to/3TId8wi
Festool 202460 ETS 150 Hard Sanding Pad - amzn.to/3TUNxjX
Do you have a link for the bit you used for the edge trimming?
Hi, I just built a bookcase with a secret door for a client and I think I under charged him... How much do you charge for those build ins...
Nice work on the units, very impressive. Another way to do this would be to use approximately 1/16" thick x 2 1/8" wide solid wood for the edging on all the plywood units. This would show less edge grain on the shelves and sides and allow the overhang to simply be sanded off and avoid the routing process altogether. The plywood would have to be glued together with spacers going the length of the sides and shelves however as the 1/16" veneer would need backing for strength. These units would get put together first without the veneer and then ripped to the correct width first to allow the edges to be perfectly square and straight. Pieces can then be be glued and clamped together with the veneer two units at a time with the veneers facing each other. I use some sort of cushion between the veneer strips to provide even pressure on the veneers and keep any excess glue squeeze out from sticking the veneers to each other. I feel anytime you can reduce the thickness of an edging or faceframe, you reduce the chances of sanding (or routing) through the often too thin veneer on plywood.
@@tomruth9487 Cool! Could you make a video please?
I've been a trim carpenter for over 45 years and he always amazes me. He definitely deserves your respect!!!!
Agreed. 👍
Same here. Been doing it for 35 years. I have a lot of respect for him.
Every day is an education.👍🏝️🇨🇦
Only 15 so it’s amazing. My dad built homes sir probably 50 yrs. I showed him a Spencer stair video one day & he watched intently. Then he commented that’s the guy you hire, give him the plans , take all his phone calls , then leave him alone? He will make both him & I money !
Why not just use 3 sheets of plywood per shelf to make up the needed thickness??
46 years in construction, 28 years in finish carpentry. love watching your videos.
I'm almost 74, but I wish I was 14 again and you were my Daddy. I would learn so much and become a carpenter like you!
Love to see a video of the poor chap painting the backs of the cabinets. Spencer I would love to see you set up a finishing department with all the space you have . We finish most everything before we fabricate. The finished product is what your judged on. Love seeing your business grow .
I think they will tape and spray with an hvlp gun
I thought the same thing......oof what a pain in the arse to tape off that stain grade oak. It makes me think it would have been better to prime and paint that back panel once before he stapled them on. But, like he said, that's not his problem...it's the painter's problem.
The back panels should have gone to the painter before assembly. It helps everybody achieve a higher quality product.
Typical shortsighted crap that you see on so many jobs: "not my problem." No way will that paint job be as good as if it were done PRIOR to the back panel installation. A better way would be to coordinate with the painter. Or, for god's sake, just roll the paint yourself! There was a time when a carpenter would pick up a paint brush or roller.
When I was active and had my own shop I was building projects like this and furniture. Since my wife passed away I sold our house and my shop and it never got back up and running again. Just took the life out of me. I like to think I was on your level on projects such as this. Love to see someone else that lives their work like you do Spencer. Look forward to your next video as always.
Sorry to hear about the loss of your wife. There are absences that are beyond filling.
Given your evident continued interest, perhaps there's a way for you to rejoin this part of yourself, maybe through teaching or some appropriate volunteer activity, to pass along your hard-earned knowledge and passion for the craft. Many could benefit from all you have to offer.
I'm sure your wife would never want you to be unhappy. I know you miss her, but for her, live a better life.
@@TerryPullen I assume you say this from experience of your own. Sorry for your loss as well😢. It's not easy, is it??
Great video! I believe that the 23 gauge, as well as 21 and 18 have a chisel point. This means that when you are firing oins,with these smaller gauges, you should be holding the gun perpendicular'
not parallel. This way, the pin will deflect to the right or left, rather than the fron or back. however, with the larger 15, and 16s, the chisel is cut the other way. and should be nailed with the gun parallel. The pins on the 23 are so small that it may not matter, but this is a good rule of thumb. I hope this is helpful. I am a retired furniture maker of 35 plus years, and am still learning. I have gained a lot of new ideas from you and enjoy very much your superb content! thanks.
Sorry for not checking my spelling! Oops!
As a carpenter myself 45 years. I want to say. Excellent video. Beautiful cabinets, well done on all aspects.
Although I'm just a lazy hobby carpenter building small furniture, I always learn something useful from your videos!
Im a electrical contractor by trade for about 30 years but have done alot of wood work also. Man would love to work with my guy here for about a year, to have the opportunity to learn from a true master of wood working. Outstanding quality work!
Can’t thank you enough for all this content that you put out.
I am a remodeler by trade, but fine woodwork and trim carpentry is my passion. The amount of knowledge I’ve gained by watching your videos is immeasurable. Keep up the great work!
Would love to take the leap and transfer to what you do, as you know, it’s not an easy step.
It is really nice to watch a video that is put out on TH-cam for informative reasons rather than entertainment. I am so tired of watching people that think that they are entertaining, but have no substance to what they’re talking about. Not only are you extremely informative and painstakingly detailed about how and why you do everything that you do but you are also entertaining at the same time because of the detail and the information that you convey. Keep up the good work. I have always enjoyed watching your videos.
Man buddy u hit the nail on thee head! I am always trying to learn! Bottom line I want to reduce the number of clients I hv to those who are aware of prices however; will pay your price w/ o haggling ! That means I hv to execute precisely in my carpentry builds! Listening to music, 10 x speed ( while they work thru what seems to them to be boring) and I am screaming nooooo I need to see how you executed that joint ! I am done I cancel and move on! I even spend hours watching framing so if a customer states I hv this issue I understand and can refer them to the right framer, roofer, ect.,. In order to be competent; passion is a huge part of it! Bout 3/4 years ago I clicked on Spencer and I found that teacher! Great resource!
very informative as always. spencer gives us for free a master class in so many aspects of carpentry and he never stops learning as we do as builders. love it! also the comprehensive breakdowns on tool set ups and case use is unrivaled. thank you!
Class A work from start to finish, and lots of good tips and advice. The painters should have stepped forward and painted the plywood back before you stapled it in place, but that’s their problem. Thank you for all the effort you put into this video.
Thr painters would have to go to Spencer's shop. I would of just added finish to the cost of the bookshelves and painted it my self
If the bookcases were done the way the designer wanted, the field finish by the painter would have been stain and finish, then paint the back (drywall). Shop paint of the back before assembly would, still require repainting on site. If this is the look the designer wanted, and the white oak was not shop finished then practically speaking there is no benefit in applying paint if stain and finish is also not shop applied. Sometimes best method has to stand behind design whims. We could argue that wanting painted drywall as a back to the bookcases is why designers are designers. Give people what they want even when you educate them on best practice and they still want something else. Possibly the designer will learn something from this project. Many designers and some architects want a specific unconventional result but maybe it’s our job to tell them how to get there. Placing a back on these bookcases when open back was the design intent…is a good example of this.
@@henrypeisch5289 I have to wonder how much thought the designer gave to this small detail of the project. To my mind placing bookcases with open backs against drywall is a non-starter for all the reasons Spencer noted. Besides, can anyone tell the difference between painted drywall and a suitably finished backer? I doubt it, especially with the bookcases full of books or whatever. Furthermore, the backer can probably take more of a hit than drywall. The owner is fortunate to have Spencer on the job.
@@theodoreshasta7846 it’s often about creating a unique design. Maybe the wall paint will be used on the 1/4” ply back. Same look as drywall. Our challenge is to work with the designer. If we need a disclaimer with a design (like installing horizontal balusters over an open to below floor space) we probably should pass on that aspect of the project. It is a goal to eventually understand as many aspects of the building process as possible so we can guide the design process without saying “no”. But there are times to say no anyway. I have always believed that licensed architects should be required to spend at least 2 years in the trades before certification. Maybe the same should apply to interior design professionals.
@@henrypeisch5289 Amen to that.
I am a finish carpenter and have done so for the last 15 yrs. For people who don't know the inner workings of running trim and doing built ins etc, He is the real deal. It's not often you see someone who delivers such high end results consistently in every aspect of his jobs. The customers are getting their money's worth without a doubt. Even us experienced carpenters learn new techniques/efficiency from watching this channel. Keep up the good work man. You have a awesome thing going and I have nothing but respect for you and what you do.. to many more years from Woodstock Ga. 👍👍💪
I guess I started at a company that did this stuff, so I really don't know any other way to do it.
The houses look similar to the ones we do.
Mr. Lewis is definitely high level, luckily I worked in a shop full of him, and I was the guy who was a master at looking stupid.
I absolutely want to see more project videos. Great work!
More to come!
I really like watching your videos. I learn so much from watching them. I am a hobbyist but you have helped me improve the quality of my work so much. Thanks for what you do and keep it up.
Spencer your videos in my opinion are the best thing to watch on TV. Keep up the good work. Next to Norm your videos are the best. This may be your most informative and fun videos you’ve made yet!
I appreciate your response I really do. I’m putting drawer faces on at the moment. Got a walk thru tomorrow. Man I know you hear this a lot but I really find your channel a breath of fresh air. You are the real deal and I relate 100%. Thank you for the tip. God bless.
You are a wonderful craftsman. I’ve been in the cabinet business for over 30 years. I know quality and you have it. The castle machine is the best money can buy
The blade with the high tooth count is a must for cross-cutting but I would still highly recommend a crosscut sled. The zero clearance with a sled really makes a huge difference as your material has virtually no chance of tearing out on the underside. Great work and awesome in depth video!
Spencer, love your videos, brother. I hope you’ll take this in the way that I mean it. Speaking for every woodworker who’s NOT in the trades, it does my heart good to hear someone like you say they’ve screwed up countless built-ins. It’s the feeling every hack golfer gets when they watch Tiger shank one into the woods. Thanks for the honesty!
I’m just getting into woodworking and cabinetry and this video blew my mind. Thank you so much for sharing. A true master crastman.
For such high quality work and expertly detailed video’s you deserve waaay more views. This stuff so much better than your next epoxy river table video. 👍
I learn more from this channel than any other. I can’t believe I get these tips for free.
Correction at 5:30
You have a *convex* bit to make a *concave* edge on the plywood. Aside from that, I’ve got nothing to add to your great work except to always say, “amazing work, Spencer!”
The convex bit makes the concave edge
@@greghope235right. That’s what I wrote. Spencer said the opposite.
That’s correct. I came to the comments to see if anyone else caught that mistake.
Nice work Spencer! After 30+ years of carpentry, I'm always learning from you. This was a fun one. You could still make this a free standing unit by adding panels to the outside. Something I might add to your shelves is to do them like floating shelves. Take two of the spacers and attach ithem to the insides of the box for each shelf. Would have been nice to paint that back panel before attaching, oh well. Many Thanks!
When I come across a channel like this, with a guy who does such a great job and gives people so many detailed and valuable explanations about how to do things the best way, I can definitely not leave without subscribing. Thank you for sharing your experience.
Welcome aboard!
It’s stunning how good these look. As professional homeowner who has tried to make similar things I’m in awe.
😊Hey there. You are absolutely amazing. You have the right tools, great shop and skills to get it done. You have patience and ability. I commend you. Thanks for sharing the videos. Philip 👊🏼
One of the best teachers I have ever had!
As always I found some little lessons you learned and passed along to help make my projects a little better or easier. Thank you.
I have a tip to prevent blowouts when nailing, so that I almost never get blowouts if I'm careful. I relates to the chisel tip on the nails and the orientation of the gun. You only get blowouts to the left or right of the gun, but never up or down, because the bevel on the nail point can guide the nail along the wood grain. Try it out!
Thanks for another great video.
I really like these project videos. Don't even mind the length. Great job!
Dude. Perfect timing. I don’t know how or why but you always post a zinger like this whenever I come up against a new challenge. Thankful beyond words.
Brilliant - thanks so much for taking the time to produce these videos. What I aspire to mostly is the level of calm you bring to your workplace. I run around like a blue arse fly then wonder where the day has gone !
Nice job. Thanks for sharing your knowledge. And yes, would love to see more like this.
I have never subscribed to a carpentry channel on the 5th minute of the first video I've watched. Really great job, a treasure trove of information.
Welcome aboard!
Surprised not to see clamps on the back edges at the filler strips to pull them together. Must be nice to work with flat plywood !
Another awesome video. Thank you and more like this please.
I so appreciate this type of video - detailed enough to really be useful, not just edited for length. And its really all about the planning and strategy separating work that is 'good enough' from...well, pretty fabulous. I hope your clients appreicate you!
This vid was a banger. I love these long form carpentry videos. So many small expert tips that add up to an incredibly professional result. I am a huge fan of the design also (except the drywall backer idea, lol). Expertly executed, Spencer. 👍 👌
My work consists mostly of shelves, builtins and mantels. I appreciate seeing your "production" techniques which come in handy for some jobs/clients.
Thanks for the amazing video. I feel like I have grown a lot as a carpenter since finding your channel.
I have a very similar situation at my house and will surely use some of the lessons here when I find time to build built-ins. Thank you!
Amazing amount of tips packed into this video. Fantastic content. Thanks!
Not making this up......as soon as the flooring is down and I run the base in my current job, I'm building two bookcases to fit in the cavities either side of their fireplace. Timing is everything! Thanks, Spencer!👍
I love how you teach. You are so specific on the details even while knowing your videos are a blend of how to and just trade enjoyment from how to place your wood to be cut to not tearout or over build to cut down. I feel like an apprentice of yours. I do feel a bit let down seeing the gaps and the top trim board installed at the home. I would have really appreciated your few extra minutes of time to at least explain how you were going to fill gaps and finish the install if you didn’t have to do the remainder of the filming. Bravo buddy you are still my favorite trim you tuber. Thanks for challenging me to be the best at all my skills with your level of detail.
Everything was fit tight besides where it met the fireplace which will be covered in brick???
Wow man. You are a busy guy. I never expected you to respond. That makes sense. That’s for pointing this out. I’m building some simple one now, nothing like yours. My brick is already there so I’ll probably need shoe or quarter on mine. Thank for the video.
Thankyou Spencer. These videos help take me to a higher level of craftsmanship
Always learn something from your vids. Thanks for explaining not only the how but the why.
More built in projects please Spencer. Thanks...
"Extra crispy" - love it! Great video!
Thank you for this detailed video ! Been watcing you for a couple years now and gotta say youre one of my top favorites to watch and i try to watch your videos as soon as they come out.
As always top notch work and outstanding results. Cant wait to see more!
I built one of these for my house early last year. I learned a lot of the stuff you laid out here the hard way. I wish you made this a year earlier but good one.
I'd like to see how you trim it out after setting them in place!
Other than some adjacent base trim at the drywall, it’s trimmed. Scribed to drywall and a short piece of white oak added at the soffit and paint grade base inside at the back panel. Thin brick will bury the stiles closest to the fireplace. Let’s hope the mason or tile guy masks off well and with clean hands.
In my day here in the southeast, the expectation was that the work would be scribed to the drywall. In those cases, shelves were usually adjustable with a single fixed shelf in the center. (Aesthetics on shelf nosings flush with the frame weren't crucial, and weight would be less). An oversize face frame would be scribed onsite and attached with the case pulled out, so glue could be applied and pocket screws could be attached. Once the FF was done, the piece would be slid back into the opening and would fit like a glove. The alternative method would use either fillers or 2-pc framing to butt the drywall.. You end up with a finished look, but the only aspect you have to sweat is scribing face frames or fillers. Dimensions on the case weren't critical. In my experience, designers always over-specify and obsess about details the average homeowner would never notice or appreciate - often driving up costs without benefit. Your 2" fixed, flush shelves being an example.
@@landonedwards7504 it might be preferred to have a designer helping the client to spend money. Higher margins maybe. We always loved them for that reason. Build in a line item for “conferences” though. Often you will have to tactfully educate a designer about best methods - in the presence of the client and this requires skill and patience. We have done it the same as you describe but attach the face frame prior to scribe. In this case with the video, with thin brick and grouted mortar joints, I would have done these cases the same with only slight structural improvements on the build. A scribe to masonry is always fun and an opportunity to show your skills but in this case, I would let the brick meet the stile - as was done in the video. The only concern is staining the raw oak with thinset or similar mortar. I believe the stile meeting drywall was scribed however. Keep watching.
Absolutely fantastic work, it's amazing to see someone who knows his tools and material so well. Thumbs up for more project videos from me.
Love your very informative and educational videos. I’ve learned so much. Please keep including the project videos. They educate and inspire.
Thanks Spencer for showing us how it’s done. Great reminders at all key steps. This video is a real confidence-builder for a project that can be a little intimidating. That Castle machine is sweet! Someday. I’m also a big believer in “idiot” marks, especially for built-ins. I tried using a Pentel Hi Polymer Block Eraser to take off pencil lines. They have worked well for me. Amazon sells them, in bulk if you use them a lot (like I do). Erasing with the grain usually takes the marks off completely, or at least close enough. Sometime you need to sand the area (w/ 180 or 220j - lightly, by hand - if the surface will be stained or clear-coated. This has worked for me to eliminate all eraser debris. I agree that a stapler is The tool for back panels. Really hold tight. It’ll stay on there nice & tight - even when you’re moving it into place. Thanks again for all of the time to take to make us better, and yes, please make more project videos. They really help.
Thanks for walking us through the details of your thought process for each step. I learned so much more that way than I would have from a simple “do this” video. It really helps me as I think about how to approach a given project.
My lord that clamp rack should come with an 18+ rating haha! Excellent video and content, as ever. Many thanks for your ongoing effort to educate us all.
Continuing to learn from you! Perfection.
I know the table saw is king but you really should think about investing in a high grade panel saw. I work for a cabinet shop in Massachusetts, the owner purchased one a few years back. It is an absolute game changer. Anways always a pleasure watching your content!
I really like your reasoning for making them bigger and then cutting down, I would not have thought about that. I have some 'chunky' shelves in my future and this is a great video to flag for rewatching.
I gotta say, nice job… your attention to detail is awesome
Now I know where I screwed up. I appreciate your video. I definitely learned something from your great video. Thank you.
Really glad you’re out there. Learning so much! Thank you.
Snother banger! Thanks for taking us to school. Invaluable! Thanks!
Outstanding video! Learned a lot of new things I’d never considered. Thank you as always.
Well, I wasn't expecting a master class in built-in shelves. Great detailed video. All the stuff and none of the fluff. Definitely a subscriber now. Thnaks!
Love your videos. I was wondering if you would possibly do a video showing how you use sketch up. I’ve seen that people have different ways of using it and would love to see how a professional carpenter goes about it. Beautiful work!
I like that you do the millwork and the installation. That's what I would like to progress to in the future.
Wow, so many excellent tips and tricks here! Thanks a ton for sharing!
I always learn a ton from your videos. I have a built-in project coming up and this gave me a bunch of useful pointers. Thank you.
I am your fan on this industry never stop learning
Once again what a great watch. Keep them coming.🇮🇪
I REALLY enjoyed this. Great woodwork, great camera work, great narration. Thanks
Very timely for a current project, thanks Spencer
Wow, great job and neat how you thought it through with the oversized shelves.
So many great tips in this one - Thanks Spencer!
2nd time to watch this video and I learned a lot from you. Thank you for sharing. Your the best carpenter I every seen
Totally jealous of your tools some really nice stuff excellent work as well. You truly have the best of everything.
Wonderful list of ideas and workflow, excellent work, even better result !
Ok I hv been using that blade I guess 3/4 weeks great blade very smooth and clean edges no tape needed ! Great find thanks buddy!
Good job like the festool router set up look fwd to seeing more ,rgd Mike fellow Carpenter and joiner in the uk😊
Thank you very for sharing great skills and talents.
Beautiful work. Thanks for sharing the tip regarding the Collins router bit for plywood edging.
More more more. Very interesting and insightful. Love your channel.
Another great project and video. Thanks Spencer
You inspired me to build some built in for a big TV and an electric fireplace. floating next to that will be 6-8 thick floating shelves, like yours.
commenting to help the algorithm....keep up the good work, your videos are the best for wood working.
I appreciate that!
Every time I watch one of your videos it costs me money ! lol never heard of that router bit before now. Excellent video Spenc!
Amazing job !! Great tips on build and tools.
Beautiful!! You just can’t beat white oak!!
Great Craftsmanship Spencer, love all of your videos. Very informative and inspiring!! Have a Great New Year’s….
It’s straight up amazing with the things you do
Beautiful cabinets Spencer. Love the attention to detail
I understand that methods and attention to detail matter, but as a newbie I wonder how much of building is just doing the work and earning the experience?
I really enjoy watching masters do the work. There’s something truly beautiful about watching something done right.
Happy New Year!
This is a great video, very informative.
Thank you so much for sharing your secrets and your knowledge.
@28:ish I had a close call with kickback recently, so that cut-to-width sequence scared me... Love your content-- nice to see a creator/ builder with confidence real-world experience
Great stuff as usual, Spencer!!!
yes i like videos like this thank for posting this videos
I love this content. This is perfect and I learned a few things