Mighty action yes its corey aka mr platinumprovocateur thank you for clarifying my two questions really appreciate it. So yes my double 18" bass reflex, B&C 8ohms drivers so as i said to my mate we should not play it in the option he said by doing 3 and 3 on each channel. though I did say to him we should do it 1 on each channel and use another amp 1 on each channel and we shall be safe because we use parallel wiring. thanks again king
1. Speaker ohms varies with the frequency youre playing through them. 2. Measure the ohms from the end of that long speaker wire Jamaicans use, and you will find you're closer to the 8 ohms, and well well pass it too..
Chow from Sound Wave was who educated me on the speaker wire raising the ohms of the speaker and that is the reason the manufacturers dont wire the speaker coil exactly to 8ohms.
I agree with using no lower than 4 Ohms. I have been djaying since 1977 and used to use the Cerwin Vega L36 (2) with a Peavey CS 800 and played it bridged at 4 Ohms and it played great all night for the parties. I now use the CVR 1504 for 4-18 inch bottoms.
no no no check the battery of the meter. the resistance wont be correct if your meter battery is low.the first reading immediately you attach the meter terminals is 7.5.so kindly replace the meter battery you will get the correct figure .thanks
Although manufacturers label their speakers @ 4, 8, and 16 ohm as just a standard, this is why they refer to it as "nominal impedance" But the actual DC resistance is usually lower. There are many factors why this is so, but it is not something you should be overly concerned about because a speaker's load is not static. It changes do to the coil moving and it changes at different frequencies while under load... I suggest you look up impedance rise, more commonly referred to as "Box rise".
the AD442 can do all six double 18's, each channelwill play 3 woofers at 2.6 ohms. wiring NL4 1+ 1- equal channel 1, 2+ 2- equal channel 2 (same way for channel 3 and 4) this way you will have 2 4 conductor speaker leads. first nl4 to 1st double 18, nl4 jumper from box 1 to box 2 then to box 3. Do this for channel 3/4 also. DO NOT BRIDGE AMP
My favourite is building banks of series and parallel. The limit always comes down to size, storage and transport. Hence people end up using the most compact and most powerful equipment. If you have a decent amp you can go super low. As soon as the voice coils warm up the impedance is much higher. I run 24x 1" drivers and i have had 26x in parallel across 4 channels. That amp was ok with it but it was not even designed to go to 2 ohms. Now they are on a 4chan 2ohm friendly. This is 1.3ohm per channel but it's only 1" drivers that warm up quickly and average much higher than 1.3 ohms. If your amp is overpowered and your load is small the impedance can be quite low, if the amp is quality.
Nice video bro! Big Up. However from my little amplifier circuits theory, the output signal from the amplifier depends on the input signal which is controlled by the knobs (attenuators) in front of the amplifier. The higher the input signal into the amplifier the higher the amplified signal out of the amplifier. The quality of the input signal (in terms of distortion and noise) and the amplitude level can result in an amplification of the same causing blowing of speakers due to overheating. Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input.
Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input. THE LAST PART OF YOUR STATEMENT IS MY POINT. HOW EVER THANKS FOR YOUR INPUT, REALLY APPRECIATE IT.
am glad I asked the question so am satisfied yes big man this was just very informative you have gone above and beyond Mighty Action bless you from corey aka platinumprovocateur over here in the United Kingdom
3 speakers at 8 ohms each wired parallel will maths out to 2.6 ohms. most single space amps don't recommend going below 4 ohms. back in the day, crowns and crest audio will do 2 ohms easily....but they will start pulling serious current....
Bridge mode just changes the 2 channel amp to a Mono block amp,both sides are being used to power a single output. As action said if you you run it hard 24/7 it will break.
Speaker ohms.. when bare coil..it will be 8ohm.. but install on speaker.. with magnet. U now have mic that puts out voltage with background noise. If u take fingers and push coil/ cone forward..u should get 8ohm..
I have a question how can you test to see which is positive and which is negative on a amplifier if it rubs off or if it's not indicae thank you for the good work. Thank you so much. Very helpful.
Hello Sir, great content first and foremost. If you amp rate for 8omh and 4omh load. You wire you box 2 8omh parallel to 4omh but the speaker really giving 3.5omh will that destroy you amp. The speak say 8omh but them really 6.5omh
Very informative. I've done a lot of research and found out these things too. First mi eva really hear a sound man come out and talk bout these things. Keep up the good work. 2 a side with some with some 21's can help build up back the loudness instead of 18's.
Mighty action, speakers are not resistive loads they are reactive loads, meaning while playing music the ohms load changes with each frequency (impedance rise) more often than not your amplifier would not be seeing let's say 2 ohm if your speakers are wired to 2 ohms, because of impedance rise the amplifier would be playing at a comfortable level. You should do some research on box/impedance rise.
Go easy my brother! Let’s clear up something. While it’s not necessarily 8 ohms using your white board 6.2 x 4 speakers is going to be 1.5 which rounded up equals 2 ohms! While it may be shocking to see those 8 ohms speakers actually reading less you have to realize they are other factors at work so in actuality the output of the amplifier isn’t going to be constant when it comes to VOLUME which is what we really work with so while we focus on ohms and watts with speakers what’s really important is the SPL! 👍🏿👌🏿so keep in mind that these numbers that you see with these specs are based on a reference using (2,4 or 8) ohm load. Under test conditions you would have a constant output with constant loads hence the reason for those numbers aka(reference) As you were sir. Don’t knock the 4 a side my friend continue there’s much more to learn 👏👏👌🏿👌🏿👍🏿👍🏿
Big boss I was in Milan when your video drop I've come back to 🇬🇧 👀 you 📹 there's some things I've learnt that I never knew I was doing wrong before 🙏🏿 up big boss 🇱🇨🇲🇸🇬🇧
So about the ad442 and ohms,, you said the subs are not 8ohms so you would NOT recommend 4per channel and that is a good advice BUT, remember "WIRE RESISTANCE " as you (previously mentioned and tested) most speakers wires are between 50ft-100ft which will automatically bring the ohms from 6.2ohms to 8ohms. Connect a 100feet speaker cable to the speaker and test the ohms from the other end of the cable and Please inbox me with the results
this i thought about and i haven't gotten the chance to do this as yet. BUT. when the manufactures was making these speakers did they put a hundred feet of wire on it? or considered that when they specified their speakers as 8 ohms?
Dont know if its factual, but what i was thought is that with wires considered the amp should see the missing 1.5 ohm. The wires for a 100 ft 12 ga. should drop between 1 to 2 ohms.
Personally mi feel the selecta, engineer or owner need to learn some of the technical side of the business. You seem well rounded and a so it fi go. Pass on the link to some friends and we a watch and a enjoy
arite me general so is it possible that when a technician build or recoil a speaker would u advise to let the technician drop the ohms to around 6. 2ohms cause normally i see technician rewind it at 7.6 or 7.9 ohms .. whats ur thought on that?
If your input signal into the amplifier is too high it will cause it try turning down the signal before it goes into the amp and then turn up the amplifier.
Bro it seems like you are relaying information that's been told to you so I'm not going to hold you to it. The reason you are getting 6.2 or 6.3 ohms is because you are reading the dc resistance when the speaker is connected to the amplifier then the coil puts out a higher value because its now in a AC circuit. In the sound system business tweeters and horns are coupled in series which gives you a better chance of not blowing them in a 4 or 5 way system each section has it's own amplifier so playing highs and horn at 16 ohms and the others at 2,4 or 8 ohms doesn't matter. And you add resistance in series not multiple cause if you had a 4 ohm in series with a 8 ohm multiplying wouldn't work as to how you doing it . Also a little nugget when you put two speakers in series it can only play as loud as one where each speaker will only play to half its potential but will survive more often than parallel.
I was tought that you are supposed to touch the tips of the multi meter probes together to measure the meters own resistance, and then take that value and add it to the value you get when measuring the speaker@@MightyAction
The importance of a small multimeter is so vital. MIGHTY ACTION GOD BLESS NA SELFISH WITH THE KNOWLEDGE. BLESS UP.
RESPECT MI G, THANKS FOR THE FEEDBACK
Mighty action yes its corey aka mr platinumprovocateur thank you for clarifying my two questions really appreciate it. So yes my double 18" bass reflex, B&C 8ohms drivers so as i said to my mate we should not play it in the option he said by doing 3 and 3 on each channel. though I did say to him we should do it 1 on each channel and use another amp 1 on each channel and we shall be safe because we use parallel wiring. thanks again king
YOUR WELCOME BRO
1. Speaker ohms varies with the frequency youre playing through them.
2. Measure the ohms from the end of that long speaker wire Jamaicans use, and you will find you're closer to the 8 ohms, and well well pass it too..
THANKS FOR THE INPUT MY BROTHER, I WILL PUT THAT TO THE TEST NEXT VIDEO
my speaker cables are cooled with liquid nitrogen
Chow from Sound Wave was who educated me on the speaker wire raising the ohms of the speaker and that is the reason the manufacturers dont wire the speaker coil exactly to 8ohms.
very true longer wires add ohms and it adds up close to 8 ohms
I appreciate the meter because I always thought that the speaker was 8 ohms now I know better thank you JAH Blessed
YOUR WELCOME, GLAD I COULD HELP
I been talking about the 4 ohm’s but people been laughing at me like I’m a fool still. But thanks for putting out here sah 💪🏾
ANYTIME.
When I do big shows I put my racks next my speakers and my speakers wires about 10 feet long 8 pin
THANKS FOR THE INPUT MI BOSS
I agree with using no lower than 4 Ohms. I have been djaying since 1977 and used to use the Cerwin Vega L36 (2) with a Peavey CS 800 and played it bridged at 4 Ohms and it played great all night for the parties. I now use the CVR 1504 for 4-18 inch bottoms.
Thanks for sharing!
no no no check the battery of the meter. the resistance wont be correct if your meter battery is low.the first reading immediately you attach the meter terminals is 7.5.so kindly replace the meter battery you will get the correct figure .thanks
Although manufacturers label their speakers @ 4, 8, and 16 ohm as just a standard, this is why they refer to it as "nominal impedance" But the actual DC resistance is usually lower. There are many factors why this is so, but it is not something you should be overly concerned about because a speaker's load is not static. It changes do to the coil moving and it changes at different frequencies while under load... I suggest you look up impedance rise, more commonly referred to as "Box rise".
THANKS FOR THE FEEDBACK, MOST DEFINITELY WILL LOOK INTO THIS.
@@MightyAction 💯
the AD442 can do all six double 18's, each channelwill play 3 woofers at 2.6 ohms. wiring NL4 1+ 1- equal channel 1, 2+ 2- equal channel 2 (same way for channel 3 and 4) this way you will have 2 4 conductor speaker leads. first nl4 to 1st double 18, nl4 jumper from box 1 to box 2 then to box 3. Do this for channel 3/4 also. DO NOT BRIDGE AMP
My favourite is building banks of series and parallel. The limit always comes down to size, storage and transport. Hence people end up using the most compact and most powerful equipment.
If you have a decent amp you can go super low. As soon as the voice coils warm up the impedance is much higher.
I run 24x 1" drivers and i have had 26x in parallel across 4 channels. That amp was ok with it but it was not even designed to go to 2 ohms. Now they are on a 4chan 2ohm friendly. This is 1.3ohm per channel but it's only 1" drivers that warm up quickly and average much higher than 1.3 ohms. If your amp is overpowered and your load is small the impedance can be quite low, if the amp is quality.
Nice video bro! Big Up. However from my little amplifier circuits theory, the output signal from the amplifier depends on the input signal which is controlled by the knobs (attenuators) in front of the amplifier. The higher the input signal into the amplifier the higher the amplified signal out of the amplifier. The quality of the input signal (in terms of distortion and noise) and the amplitude level can result in an amplification of the same causing blowing of speakers due to overheating. Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input.
Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input.
THE LAST PART OF YOUR STATEMENT IS MY POINT.
HOW EVER THANKS FOR YOUR INPUT, REALLY APPRECIATE IT.
Correct ia. That where the limiter in the speaker management comes into play.
am glad I asked the question so am satisfied
yes big man this was just very informative you have gone above and beyond Mighty Action bless you from corey aka platinumprovocateur over here in the United Kingdom
Glad to help
Keep up the good work Mono vs. Stereo setup should be your next topic.
Thanks for the idea!
Good conversation learned something every time I watch your channel thanks for all you do
your welcome
Love the teachings iya
Respect
3 speakers at 8 ohms each wired parallel will maths out to 2.6 ohms. most single space amps don't recommend going below 4 ohms. back in the day, crowns and crest audio will do 2 ohms easily....but they will start pulling serious current....
Very true
Big up
1.5 if u round it off to 1 decimal place is 2 ohms because 5 and up u round up. However good teaching respect
I thought about that too. But just showing the actual numbers
Bridge mode just changes the 2 channel amp to a Mono block amp,both sides are being used to power a single output. As action said if you you run it hard 24/7 it will break.
EXACTLY
Well done very well expected 👍🏿
Thanks 🙏
Speaker ohms.. when bare coil..it will be 8ohm.. but install on speaker.. with magnet. U now have mic that puts out voltage with background noise. If u take fingers and push coil/ cone forward..u should get 8ohm..
To be honest it is good to learn because from you I learn alot just now respect to you mi general
Respect
Keep up the good work mighty action nice of you to give your time so appreciated
Respect
Glad you mentioned about the cabling excellent
Glad it was helpful!
I've got it 100% thanks again from corey in United Kingdom - London
YOUR WELCOME
I have a question how can you test to see which is positive and which is negative on a amplifier if it rubs off or if it's not indicae thank you for the good work. Thank you so much. Very helpful.
not sure what your referring to, but i would look up the manual and look at other amps like it.
what amps is this?
wiring of components and speaker leads drops the impedence fo all speakers
Hello Sir, great content first and foremost. If you amp rate for 8omh and 4omh load. You wire you box 2 8omh parallel to 4omh but the speaker really giving 3.5omh will that destroy you amp. The speak say 8omh but them really 6.5omh
You should be ok, but when you are driving those speakers hard you might have some issues.
Very informative. I've done a lot of research and found out these things too. First mi eva really hear a sound man come out and talk bout these things. Keep up the good work.
2 a side with some with some 21's can help build up back the loudness instead of 18's.
RESPECT ME G
Mighty action, speakers are not resistive loads they are reactive loads, meaning while playing music the ohms load changes with each frequency (impedance rise) more often than not your amplifier would not be seeing let's say 2 ohm if your speakers are wired to 2 ohms, because of impedance rise the amplifier would be playing at a comfortable level. You should do some research on box/impedance rise.
I always try to use 4ohm to not run the components at the limit as with 2ohm. I leave 2ohm for emergencies 💪🏾💪🏾
THANKS FOR SHARING.. GOOD PRACTICE
Go easy my brother!
Let’s clear up something.
While it’s not necessarily 8 ohms using your white board 6.2 x 4 speakers is going to be 1.5 which rounded up equals 2 ohms! While it may be shocking to see those 8 ohms speakers actually reading less you have to realize they are other factors at work so in actuality the output of the amplifier isn’t going to be constant when it comes to VOLUME which is what we really work with so while we focus on ohms and watts with speakers what’s really important is the SPL! 👍🏿👌🏿so keep in mind that these numbers that you see with these specs are based on a reference using (2,4 or 8) ohm load.
Under test conditions you would have a constant output with constant loads hence the reason for those numbers aka(reference)
As you were sir.
Don’t knock the 4 a side my friend continue there’s much more to learn 👏👏👌🏿👌🏿👍🏿👍🏿
Love the lingo from st lucia
Respect
The few amplifiers that play 2ohm all day and night are Power Soft K series, FFA, Void infinite 8.....
You got me thinking 🤔
Which sound wasi are in Jamaica Denton
yes mighty action I shall stay in that theory
👍🏾
Big boss I was in Milan when your video drop I've come back to 🇬🇧 👀 you 📹 there's some things I've learnt that I never knew I was doing wrong before 🙏🏿 up big boss 🇱🇨🇲🇸🇬🇧
RESPECT
So about the ad442 and ohms,, you said the subs are not 8ohms so you would NOT recommend 4per channel and that is a good advice BUT, remember "WIRE RESISTANCE " as you (previously mentioned and tested) most speakers wires are between 50ft-100ft which will automatically bring the ohms from 6.2ohms to 8ohms. Connect a 100feet speaker cable to the speaker and test the ohms from the other end of the cable and Please inbox me with the results
this i thought about and i haven't gotten the chance to do this as yet.
BUT.
when the manufactures was making these speakers did they put a hundred feet of wire on it? or considered that when they specified their speakers as 8 ohms?
@dadalinks yes I agree that should be another topic
Good call mono v stereo set up 👍🏾
THATS ON MY AGENDA, BUT I WANT THAT TO BE A SPECIAL TOPIC SO I'M WORKING ON THE THINGS FOR THAT
Dont know if its factual, but what i was thought is that with wires considered the amp should see the missing 1.5 ohm. The wires for a 100 ft 12 ga. should drop between 1 to 2 ohms.
STILL LOOKING INTO THIS, BUT I TOO DON'T THINK ITS FACTUAL
Bro does the amplifier really does its rated power watt i dont think so that the amp will put that much power watt
I’m not a 100% sure, but if I would guess it would be no. These manufacturers like to exaggerate for selling points
@@MightyAction ok bro
The Jamaica don't know one dam thing about those things till they know how much them a play for
What that means bro?
Personally mi feel the selecta, engineer or owner need to learn some of the technical side of the business. You seem well rounded and a so it fi go. Pass on the link to some friends and we a watch and a enjoy
Respect, hope unu subscribe too 😬
Four Calum that means they are not playing off of none
We can damaged the sound speakers to compete
That's right not with those amplifier
That's the same way I run my system 2 a side on my amplifier
Nice 👍
yes 2 per side is the rule for good sound . I play with the I Nuke 12000 and everybody say you sound good
Thanks for sharing mi boss 👍🏾
Yes u real 8ohm boss
Me too on my little sound
arite me general so is it possible that when a technician build or recoil a speaker would u advise to let the technician drop the ohms to around 6. 2ohms cause normally i see technician rewind it at 7.6 or 7.9 ohms .. whats ur thought on that?
REWIRE IT TO 8 OWMS
Play the 18"like it's 21"
What gauge wire do you use?
USE FOR WHAT?
@@MightyAction subs mid bass mid high horns tweeters
CURRENTLY USE 13 GAUGE ON TOPS (HORN, TWEETERS, HIGH MID AND LOW MID). USE 12 GAUGE ON BASE BUT I'M ABOUT TO SWITCH TO 10
You need a impedence meter to get 8ohms
So I’ve been told. Going to get one and re do the test one of these days
How would you wire 2 8ohms tweeter to get 8 ohms?
You cannot, you can only get 4 (parallel) or 16 ohms (series)
@legomanstar251 IS 100% CORRECT.
BUT YOU CAN USE TWO 16 OHMS TWEETERS IN PARALLEL TO GET THE 8 OHMS YOU WAN'T
I don't understand is stereo Bass nighter
May be up to 8 ohm
How get more volume with out peaking it
If your input signal into the amplifier is too high it will cause it try turning down the signal before it goes into the amp and then turn up the amplifier.
Bro it seems like you are relaying information that's been told to you so I'm not going to hold you to it. The reason you are getting 6.2 or 6.3 ohms is because you are reading the dc resistance when the speaker is connected to the amplifier then the coil puts out a higher value because its now in a AC circuit. In the sound system business tweeters and horns are coupled in series which gives you a better chance of not blowing them in a 4 or 5 way system each section has it's own amplifier so playing highs and horn at 16 ohms and the others at 2,4 or 8 ohms doesn't matter. And you add resistance in series not multiple cause if you had a 4 ohm in series with a 8 ohm multiplying wouldn't work as to how you doing it . Also a little nugget when you put two speakers in series it can only play as loud as one where each speaker will only play to half its potential but will survive more often than parallel.
Yeah put the bridge sounds
Because those sound is not a normal sound system why they play four Calum
Gn how do u make your power distro with a transform
no. no transformer in my distro
if you do one with a transformer it would be a stabilizer
Thanks for tha info
You have to make them
i git 7.9 ohms on my 18s ref l 18p400
2 ohm 3 ohm 4 ohm 8ohm 16 ohm
3 ohm on to 8 ohm
You are using the wrong tool. You should be using an impedance meter not a multimeter.
Going to re-do this again
I was tought that you are supposed to touch the tips of the multi meter probes together to measure the meters own resistance, and then take that value and add it to the value you get when measuring the speaker@@MightyAction
Uno have some education I don't see it so
You know say me get it because it is still in your head
Who that bambeno
What