3G Fluxcore Root Pass/Ceramic Backing (Part 1)

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 158

  • @LeadRakFPS
    @LeadRakFPS 2 ปีที่แล้ว +18

    You'll get little to no spatter while welding fluxcore if you back your wire speed down or turn your voltage up. I realize a coupon won't hold as much heat input, so backing your wire speed down to around 325-350 @ 24 volts will help it smooth out. I've built tanks for years and not just thin wall either. Even on 3" thick material I'm only around 28-30 volts and 400-450 on my wire speed. It turned out great, but the spatter you were getting while welding your root pass can be adjusted out 100%.

    • @Sadoroi
      @Sadoroi ปีที่แล้ว

      Thanks sharing the information 👍👍👍

    • @livingintheLight.
      @livingintheLight. ปีที่แล้ว

      The way that thing is hissing, he's probably spraying as it

    • @LeadRakFPS
      @LeadRakFPS ปีที่แล้ว +1

      @livingintheLight. And? Just because he's at spray transfer settings doesn't mean it won't still leave spatter with the wrong combo of wire speed to voltage. Conversely, it will still leave spatter if below spray transfer and you have the wrong combination of wire speed to voltage. There is an actual sweet spot for settings wise when welding flux core. Especially dual shield. Doesn't matter what brand of inverter or suitcase/wire feeder you're using, either. The settings inside the feeder are pretty close starting points and usually only take a few seconds to adjust any spatter out (with the exception of tiny tiny little pin head bb's that easily come off while raking a wire brush or grinder with a wire wheel over it).

    • @ShBenEd
      @ShBenEd ปีที่แล้ว

      That and, don't you want to run a little cold to keep the vertical weld from falling out?

    • @marcusfree294
      @marcusfree294 ปีที่แล้ว

      What’s some good volts for horizontal?

  • @Fred213.
    @Fred213. ปีที่แล้ว +3

    Great stuff man wish I had these videos 10yrs ago…

  • @EbubeDerickmuem-xy7vf
    @EbubeDerickmuem-xy7vf 10 หลายเดือนก่อน +1

    You weld really good your a good welder

  • @juicypbc1998
    @juicypbc1998 9 วันที่ผ่านมา

    What welding wire can you run multiple pases with specifically weld on top of weld type of situation

  • @joeyhercer8432
    @joeyhercer8432 2 หลายเดือนก่อน

    Nice how many ampere you used in welding ceramics

  • @keithhunchuk3049
    @keithhunchuk3049 2 ปีที่แล้ว +19

    Oh for verticals we were always taught to point it down. Makes it alot easier to not skip out of the puddle. Try about 10°-15° down!

    • @44_83
      @44_83 2 ปีที่แล้ว

      @@texasmadeweldingacademy8901 I like your weld shirt. Where can I buy that mufcka?

    • @NathanPalmer
      @NathanPalmer 10 หลายเดือนก่อน

      Absolutely not. Places will fail you for that. I mean, ask if you can first but they usually tell what they want for progression. Anywhere I’ve been it’s 45 degrees up.

    • @keithhunchuk3049
      @keithhunchuk3049 10 หลายเดือนก่อน

      A 45 degree angle up? You sir do not have a clue what your talking about. I work in a ship yard that produces ships for navy and coastgaurd​. I am a welder foreman and teach welders to pass UT and RT welds using ceramic backing. So thanks for your input! @NathanPalmer

    • @Antti_Iltanen
      @Antti_Iltanen 5 หลายเดือนก่อน

      Came to say the same as Keith. Always done root pointing downwards at an angle. These little pieces are easy but once you have a 10ft tall wall you gotta weld up it'll change the gap during your weld. Once it starts to get more narrow you run a risk of stitching the sides together and not really feeding enough of your puddle to the backing groove to form that root. Also, it's more common to poke the backing out with your wire if you point it up.
      For filler and cap beads you can point up and push the puddle but for the root you're better off pointing down 👇
      At least this is the standard when welding cruise ships.

    • @vonzsuaellojohnson7583
      @vonzsuaellojohnson7583 หลายเดือนก่อน

      I've always pointed down 👍

  • @nathanhighvoltage5259
    @nathanhighvoltage5259 2 ปีที่แล้ว +6

    Vertical has always given me problems after a few seconds. It’ll eat itself. Thanks. Great work

    • @SouthernGntlmn
      @SouthernGntlmn 2 ปีที่แล้ว +7

      Stick or wire? (Mig/flux) turn your heat down to like 24-25 V. Wfs about 400-425. Work angle at 90* and slightly upwards. It will look like it’s going to blow out but be patient and it will fill in. Most shops don’t want any weave action these days so just drag your puddle up and even back step slightly without pulling out of your puddle too extreme. It’s a finesse thing and extreme patience. Practice is all that can help you perfect it. Stay with it you’ll have it down in no time.

    • @crooknine3251
      @crooknine3251 ปีที่แล้ว

      @@SouthernGntlmn that’s a damn good explanation

    • @SouthernGntlmn
      @SouthernGntlmn ปีที่แล้ว +4

      @@crooknine3251 lol thanks I’ve been welding for 20 years so anytime I can pass along some knowledge I will. I like helping the up and coming guys and try to teach them how to do things the right way.

  • @mdmuradshake5002
    @mdmuradshake5002 ปีที่แล้ว +2

    ❤I am a Bangladeshi I love your welding I have subscribed your channel love you bro❤

  • @felixrocha3405
    @felixrocha3405 ปีที่แล้ว +1

    Nice! Do y’all still have shirts for sale?? I want one asap!

  • @wesleychase2827
    @wesleychase2827 3 หลายเดือนก่อน

    What was the thickness of those test plates?......i have a 1 inch plate test coming up....flux core 0.54 wire with ceramic tape....i have to do a 2G...3G... and a 4G..... I've worked in shipyards before but mostly welded 3/4 plate...so this is going to be fun 😎🔥💯💪🧑‍🏭🇺🇲

  • @agussutisna1361
    @agussutisna1361 ปีที่แล้ว

    @Texasmadewelding 10:25
    A sama v di speder berapa di kasih ya

  • @JewelAhmad-et5le
    @JewelAhmad-et5le ปีที่แล้ว

    i want to know about verticle ceramics jobs, it is only root pass or hot passs

  • @marcusfree294
    @marcusfree294 ปีที่แล้ว

    Do you use that same setting for horizontal as well ?

    • @Bagnon609
      @Bagnon609 10 หลายเดือนก่อน

      In horizontal, you can usually turn the heat up a bit depending on the thickness of the plate/material, the angle of the work, and the size of the gap. Particularly, the root. Open root welding needs special attention.

  • @selamet654
    @selamet654 2 ปีที่แล้ว +3

    thank you for the guidance sir. hopefully it will be useful

  • @pawa5235
    @pawa5235 2 ปีที่แล้ว

    Thanks for your guidance please what voltage and wire speed did you used I want to be sure....thanks

  • @THEENGINEERSRPM-ER-SUNIL-KR
    @THEENGINEERSRPM-ER-SUNIL-KR ปีที่แล้ว +1

    Copper or ceramic backing which one is better what is the difference kindly explain

    • @Bagnon609
      @Bagnon609 10 หลายเดือนก่อน

      Depends on the type of ceramic. In this case, the ceramic used is probably a general type being used as a backing (protects the weld from the back where the shielding gas can't access). Copper can transfer heat better, but is more expensive. If you need to control the heat more precisely, then a copper backing might be the better option. It will help by maintaining an even level of heat throughout the weld process.

    • @THEENGINEERSRPM-ER-SUNIL-KR
      @THEENGINEERSRPM-ER-SUNIL-KR 10 หลายเดือนก่อน

      @@Bagnon609 Thanks for reply

  • @jerryvwallace2
    @jerryvwallace2 ปีที่แล้ว

    Is this straight fix core or dual shield?

  • @moisesrodriguez2931
    @moisesrodriguez2931 2 ปีที่แล้ว +1

    Bad ass content keep them videos coming bro

    • @texasmadeweldingacademy8901
      @texasmadeweldingacademy8901  2 ปีที่แล้ว

      Thanks Brother ! Any ideas on content is always Good…

    • @moisesrodriguez2931
      @moisesrodriguez2931 2 ปีที่แล้ว +1

      @@texasmadeweldingacademy8901 2 or 6 inch sch 10 stainless with that meticulous explaining on both languages would be great , pretty sure will get views and will reach to a lot of people to meet your channel boss

    • @moisesrodriguez2931
      @moisesrodriguez2931 2 ปีที่แล้ว +1

      @@texasmadeweldingacademy8901 I'm actually on that learning curve on that sch 10

  • @ritzwebceo529
    @ritzwebceo529 2 ปีที่แล้ว

    What F,Aand P number and positions do you recommend this combo , of, Ceramic backing and fillers and is it recommended only for FCAW ?

  • @alvinjoy9392
    @alvinjoy9392 ปีที่แล้ว

    Should i hold the torch downwards

    • @Bagnon609
      @Bagnon609 10 หลายเดือนก่อน

      You mean aiming the nozzle/wire downwards as you move up? No, that would be bad. The weld puddle will be forced down and gravity gonna do what gravity does. :D

  • @angelmontiel3186
    @angelmontiel3186 ปีที่แล้ว

    Self shielded or duel shielded

  • @HugoGonzalez-vj2eb
    @HugoGonzalez-vj2eb ปีที่แล้ว +2

    Compa megustan un chingo tus videos cuando sacas unos en español saludos desde las Vegas

  • @josesilva-ue5kv
    @josesilva-ue5kv ปีที่แล้ว

    que lápis é esse ? é giz ? que blusão de solda é esse ?

  • @choruzvargas4009
    @choruzvargas4009 ปีที่แล้ว

    What amp and wire speed u had

  • @Spiderman20888
    @Spiderman20888 2 ปีที่แล้ว

    Cu ce camera, filmezi,?

  • @FAUZIAKBAR89
    @FAUZIAKBAR89 2 ปีที่แล้ว +1

    Good job sir. Tnks you very much.🙏 Tutirial very good 🤝🇮🇩 my from indonesia

  • @manojsree1457
    @manojsree1457 2 ปีที่แล้ว

    Thank u sir,,good,,description, iam from kerala,india

  • @caioanndre
    @caioanndre ปีที่แล้ว +1

    Tira onda DEUS continue abençoando 🙏🙏

  • @WalterNegola
    @WalterNegola ปีที่แล้ว

    I, HOW ARE YOU DOING?
    MY NAME IS WALTER NGOLA, I’M FROM ANGOLA 🇦🇴 “ÁFRICA “ AND I’VE BEEN WATCHING YOUR VÍDEOS ON TH-cam. I’M YOUR FOLLOWER AND REALLY LIKE WHAT YOU DO.
    BUT, I’M VERY INTERESTED TO MAKE A WELDING COURSE WITH YOU. SO HOW CAN I DO TO MAKE IT HAPPEN??

  • @josebenavides3310
    @josebenavides3310 7 หลายเดือนก่อน

    Diameter of fluxcore??

  • @agussutisna1361
    @agussutisna1361 ปีที่แล้ว

    Amper di speder brapa..

  • @BiplabSengupta-d8o
    @BiplabSengupta-d8o ปีที่แล้ว

    Excellence sir!❤❤❤❤❤🎉🎉🎉

  • @israelquijano6097
    @israelquijano6097 2 ปีที่แล้ว

    Cuanto de alambre le pusiste?

  • @darwinsaputra9482
    @darwinsaputra9482 2 ปีที่แล้ว

    Terimakasih masukanny suhu

  • @shahidsiddique4430
    @shahidsiddique4430 ปีที่แล้ว

    How meny current sir

  • @Matt-uj6jm
    @Matt-uj6jm 2 ปีที่แล้ว +3

    Fond memories North Sea 🏴󠁧󠁢󠁳󠁣󠁴󠁿 Multi coded pipe welder always got a perfect root with the backing tiles thanks for sharing 👍

    • @springer3783
      @springer3783 ปีที่แล้ว

      You must be rolling in the cash now , I know a guy who was in 50k debt and went out to the rigs in the North Sea and cleared his debt and bought a house and a bmw m3

  • @jamesparera4923
    @jamesparera4923 ปีที่แล้ว

    How many V And ipm for root pass?

  • @cotcheaziz
    @cotcheaziz ปีที่แล้ว +3

    Hello Sir, I liked the content that you are doing, as it is beneficial to the community and to the trainees. In turn, I thank you for this beautiful content, and for this I would like to publish your videos in the Arab world. Of course, I will dub all the technical words and everything that goes on in the video or content. And appreciation❤️❤️

    • @LilFish0
      @LilFish0 ปีที่แล้ว

      Well said

  • @PAPSCHARLIE13-2-16
    @PAPSCHARLIE13-2-16 ปีที่แล้ว +1

    Shout out bro from Philippines im also a welder smaw can you offer me a job their in your country

  • @mariomendoza7822
    @mariomendoza7822 2 ปีที่แล้ว

    HOLA AMIGO CUANFO SACAS UN TUTORIZL DE 3F, 3G Y 4G SALUDOS Y GRACIAS

  • @BwinCROATIA
    @BwinCROATIA 11 หลายเดือนก่อน

    Nice bro

  • @robertwaltersagbayyumbla7150
    @robertwaltersagbayyumbla7150 ปีที่แล้ว

    complimenti muy bonito el cordon muchos saludos

  • @marcusfree294
    @marcusfree294 ปีที่แล้ว

    We need a horizontal video too mayne

    • @ethan-py9he
      @ethan-py9he 8 หลายเดือนก่อน

      If u can do vertical you can do horizontal

  • @fidelrivas3256
    @fidelrivas3256 ปีที่แล้ว

    Me gustaria tener mas informasion de ute

  • @7538ivan
    @7538ivan 2 ปีที่แล้ว

    Can you do a 2 g flux ceramic please please

    • @keithhunchuk3049
      @keithhunchuk3049 2 ปีที่แล้ว

      On 2g you need top bevel to be 30° and bottom to be 15° with a 4mm gap. Using 0.45 wire with 100% co2 you would set it to 21 volts and 210 wire speed ipm. Angle it back into the puddle and slightly 10° up to make sure you are grabbing the top edge

  • @agrikabavlog2404
    @agrikabavlog2404 2 ปีที่แล้ว +1

    What voltage and ampers u used for that penitration sir?

    • @joeyhercer8432
      @joeyhercer8432 2 หลายเดือนก่อน

      How many ampere you used penitration

  • @josecapitule1812
    @josecapitule1812 10 หลายเดือนก่อน

    Very nice.

  • @genehong85
    @genehong85 ปีที่แล้ว +1

    I see porosity on the back😮

  • @juansotelo8538
    @juansotelo8538 2 ปีที่แล้ว

    Tienes estos vídeos en español

  • @gaddur1
    @gaddur1 2 ปีที่แล้ว

    How much ampre do you use for 3g

  • @fidelrivas3256
    @fidelrivas3256 ปีที่แล้ว

    Megutaria aser un curso con utede

  • @Coachtosu
    @Coachtosu 2 ปีที่แล้ว

    Ampere ??

  • @Weldinginlove
    @Weldinginlove 2 ปีที่แล้ว

    Thanks for your video. . Excellent 🔥🇮🇩❤️

  • @sarath6214
    @sarath6214 ปีที่แล้ว

    Show a pipe welding Video one please

  • @morganweller1491
    @morganweller1491 2 ปีที่แล้ว

    Slick ASF!!!!!

  • @melbinmathew9092
    @melbinmathew9092 ปีที่แล้ว

    I'm a mig welder... good job bro.....mig welder vacancy in your company . pls help India....how much wire speed..

  • @mikejohn3265
    @mikejohn3265 2 ปีที่แล้ว

    Great job thanks.

  • @obiefabiodzvokora7007
    @obiefabiodzvokora7007 2 ปีที่แล้ว +1

    Great work 👏

  • @SLKIWEN
    @SLKIWEN ปีที่แล้ว

    tnx

  • @Chaminda_
    @Chaminda_ 2 ปีที่แล้ว

    Good job

  • @JonathanPowers-oz5mw
    @JonathanPowers-oz5mw 8 หลายเดือนก่อน +1

    More wire and a little heat

  • @KillinGameToniCastro
    @KillinGameToniCastro ปีที่แล้ว

    Nice. WHO hiring. I’m definitely trying to work. Oilfield or Offshore.

  • @junjunbaya9571
    @junjunbaya9571 ปีที่แล้ว

    I'm Here in the Philippines, Do you have a Job Offer Sir? I have a 6 years experience in Welding Jobs.

  • @sergiomurata7549
    @sergiomurata7549 ปีที่แล้ว

    😂😂😂😂 saiu com mordedura meu amigo,não eh assim que se faz,a solda sai feio atrás 😅

  • @mohammedsaifulla8155
    @mohammedsaifulla8155 ปีที่แล้ว

    👌👌👌👌👌

  • @hariomwelder
    @hariomwelder ปีที่แล้ว

    Porosity

  • @toronjillo2
    @toronjillo2 2 ปีที่แล้ว +1

    Why am i geting a hole am i going too slow? Or angle or amps? Thanks

    • @texasmadeweldingacademy8901
      @texasmadeweldingacademy8901  2 ปีที่แล้ว +1

      It can be your running to hot.. or staying to much in the middle.. try to pause a full second on your sides to stay away from the middle and spread your heat input

  • @weldsnmore3710
    @weldsnmore3710 2 ปีที่แล้ว

    🔥🔥🔥

  • @samanthawickramarathne4320
    @samanthawickramarathne4320 ปีที่แล้ว

    Sir good working do its your

  • @duraistalin2889
    @duraistalin2889 2 ปีที่แล้ว

    Very nice bro..😍

  • @borceapostolovski372
    @borceapostolovski372 3 หลายเดือนก่อน

    Brother Mother try next time to show adjustment on your machine

  • @hamisihalfan3100
    @hamisihalfan3100 ปีที่แล้ว

    Im a welder from Kenya I need job

  • @morganweller1491
    @morganweller1491 2 ปีที่แล้ว

    Why is everyone asking for amperage first figure it out he's not welding you are and it's in the vid!!

  • @osvaldorivero4242
    @osvaldorivero4242 2 ปีที่แล้ว

    BRAVO !!!!!

  • @TrungLe-sf7og
    @TrungLe-sf7og ปีที่แล้ว

    Hàn mà đường hàn bị rỗ khí thế kia thì vứt 😅😊

  • @ارواحمغامرا
    @ارواحمغامرا 2 ปีที่แล้ว

    ذكرتني ب عبود سكيبه 😂

  • @keithhunchuk3049
    @keithhunchuk3049 2 ปีที่แล้ว +1

    Ceramic overhead. I dont think gravity would be on your side there my guy. Flat, vert and horizontal all day though. 😋

    • @texasmadeweldingacademy8901
      @texasmadeweldingacademy8901  2 ปีที่แล้ว +1

      👍🏽

    • @paulhazley7596
      @paulhazley7596 ปีที่แล้ว

      It is possible overhead just a little more difficult

    • @keithhunchuk3049
      @keithhunchuk3049 ปีที่แล้ว

      @Paul Hazley there wouldn't be any root reinforcement and it would have low spots on root side. Would be OK if you were gouging it out and then filling from root side but not for a finished weld to be ready for NDT. The other three positions are able to leave behind finished product being welded from one side only.

    • @paulhazley7596
      @paulhazley7596 ปีที่แล้ว

      Not if its done properly

    • @keithhunchuk3049
      @keithhunchuk3049 ปีที่แล้ว

      @Paul Hazley oh really? What would the proper fit up look like? Which tiles would you use? Bevels + root opening gap and what settings with what size and type of wire? I'm super interested to know. Maybe the shipyard I work in that builds ships for the navy has some things to learn...

  • @avtaravtargill4053
    @avtaravtargill4053 ปีที่แล้ว +1

    ❤❤❤❤❤🎉🎉🎉👏👍☕

  • @Spiderman20888
    @Spiderman20888 7 หลายเดือนก่อน

    🎉🎉🎉😊😊😊😊😊

  • @hasibulkhankalkata4264
    @hasibulkhankalkata4264 2 ปีที่แล้ว

    MIg welder 3g INDAN

  • @SonNguyen-ke2yw
    @SonNguyen-ke2yw ปีที่แล้ว

    Tôi đã hàn lót sứ đường 3g trong khoảng 18năm và tôi đã không cần phải đánh võng như bạn . tôi chỉ cần giữ nguyên và đi thẳng lên . Thanks! Hy vọng bạn biết Vard Norway .

  • @Kumarnipun-p2g
    @Kumarnipun-p2g ปีที่แล้ว

    👌👌👌👌👍

  • @tribambang4507
    @tribambang4507 ปีที่แล้ว

    I am welder Indonesia

  • @EbubeDerickmuem-xy7vf
    @EbubeDerickmuem-xy7vf 10 หลายเดือนก่อน

    I need a job I'm a very good stick welder I'm in Africa Cameroon is my location

  • @afrakomahlucy1567
    @afrakomahlucy1567 ปีที่แล้ว

    Please sir I'm girl of twenty five and I'm a welder , please can you help join you I want to Learn more

  • @rakeshgiri4780
    @rakeshgiri4780 2 ปีที่แล้ว

    Ok

  • @mikejohn3265
    @mikejohn3265 2 ปีที่แล้ว +1

    Why not a sharp edge?

  • @awishkaakalanka7751
    @awishkaakalanka7751 2 ปีที่แล้ว

    😊👍🏻

  • @WELDERMADEHEADBANDS
    @WELDERMADEHEADBANDS 2 ปีที่แล้ว

    👍🏽

  • @พนม1970
    @พนม1970 ปีที่แล้ว

    🙏👍👌

  • @malaumalau419
    @malaumalau419 10 หลายเดือนก่อน

    Volt 24 = ok.
    Speed 400=???
    🤔🤔

  • @meddebzied9128
    @meddebzied9128 ปีที่แล้ว

    Renvoyer vidéo en français

  • @Maximko23life
    @Maximko23life 6 หลายเดือนก่อน

    С керамикой это правильно, но не серьезно

  • @sonnyhernandez5491
    @sonnyhernandez5491 ปีที่แล้ว

    Tf that noise??

  • @travisjones9508
    @travisjones9508 2 ปีที่แล้ว +1

    At my job they use ladybois to weld tubes from Thailand 🇹🇭

    • @44_83
      @44_83 2 ปีที่แล้ว

      What the fck is a ladyboi

  • @oliverfamisaranjr5709
    @oliverfamisaranjr5709 2 ปีที่แล้ว

    sir,,, can i mine your jacket,,,,

  • @sanjaymoremore9156
    @sanjaymoremore9156 2 ปีที่แล้ว

    सर आप कभी कभी हिंदी भी बात करा करो

  • @sergio6760
    @sergio6760 ปีที่แล้ว

    Kkkk,ficou feio heim,a nao ser que nos EUA solda de qlqer jeito😅

  • @vuhoanginh1505
    @vuhoanginh1505 6 หลายเดือนก่อน

    Hàn thế mà cũng làm youtube thì chịu

  • @gintaraslinkevicius4832
    @gintaraslinkevicius4832 7 หลายเดือนก่อน

    look less at incorrect welding methods !!!This bud is 99% defective