Pro scooter #2. Thx, works fine, new accelerator $12. Only problem was in part when you need move new wires through the hole, I have to remove 2 screws in top and bottom of Light then remove light, you can then press a wires from front side, without it it was not possible, connector was blocked in hole by rest of wires, it is more safe also :) Easy and cheap replacement.
@@fngfng1306 sometimes you need just a open sensor and blow inside the connection of wire cable, sometimes the dust can be inside and make problem, bit if that not help than replacement
My xiaomi essentiel will not turn off. I tried to tune it showed error 14, but i am still able to drive on it. Only issue is it will not turn off and i can't drive 30 km speed even i hacked it.
I have a problem with the Xiaomi Pro 2 scooter. It lasts a long time when turned on and lasts a long time when turned off. After that, it started working on its own and I cannot change the mode or adjust the lighting. Is there a solution?
could be the controller board got little bit of moisture , i used isopropane alcohol to clean it and then hair dryer to get all the moisture out and it worked after that as new
i had the same problem but reseting it helped , no more error signal is shown . problem is now that even fullt charged and in S mode scooter is not going above 20 km/h , before it was going at least 25 km . how can i fix that ?
@@calminjarris4179thanks for the response , I replaced it - beeping stopped but now I have issue with speed - it’s not going over 20 km/h , before it was easily taking up to 27-28 km/h
I purchased a xiaomi electric scooter 4 lite brand new I believe I've read the instructions correctly but it will not connect to my phone via Bluetooth and yet it will still go at at 10kmh I'm lost
Bro plz help me ! I think water went inside the screen was blank so i use isopropyl alcohol and scratch thebutton , the screen starts to appear but bro there is error 14 i tried alot
If it is broken you need to replace, sometimes just need to open and disconnect connector there lose contact cuz of dust inside, so you can try in this way
thank you so much for your video.
which screwdriver size do we need to unscrew the 3 little screws on the screen?
just use star screwdriver it's gonna unscrew these
Pro scooter #2. Thx, works fine, new accelerator $12. Only problem was in part when you need move new wires through the hole, I have to remove 2 screws in top and bottom of Light then remove light, you can then press a wires from front side, without it it was not possible, connector was blocked in hole by rest of wires, it is more safe also :) Easy and cheap replacement.
Nice work!😉
Шо було
Tysm. Its more tricky than it looks in the video so take your time guys but it worked 100%
Glad it helped
Thank You!🙂
@@OYY8 oki merci
Best tutorial na YT so far.
Glad to hear that
Thanks!
Thanks for tip it works for me without replace
Glad it helped😉
Hi,how did you fix the sensor?
@@fngfng1306 sometimes you need just a open sensor and blow inside the connection of wire cable, sometimes the dust can be inside and make problem, bit if that not help than replacement
Thank you. I freaking stripped the wires down and twisted them together like a crackhead
😁🤙🏻
My xiaomi essentiel will not turn off. I tried to tune it showed error 14, but i am still able to drive on it. Only issue is it will not turn off and i can't drive 30 km speed even i hacked it.
MERCI
welcome!
thanks!
Welcome!
شكرا ضبط 🙏
Welcome😉
Thanks bro
You are welcome Any time
هل تم تغير كسيراتور بالكامل انا عندي المشكل نفسه
Thank you, it helped me to fix this error 🎉
Glad it helped thanks🙂
just ordered new one today, lets see what happen. Thank you
Hope you fix it! Thanks!
Anche dopo averlo caricato durante la notte, al mattino si è spento dopo 2 minuti. cosa posso fare ora
Replace
Mine just became bumpy but still goes, have new accelerator but still error 14? New battery new motor?
Changed the screen/display and it working easier
I have the ninebot f25e over a year now,and when I go over bumps it’s goes straight to a red flashing spanner light.?
Something weird happening with some connection
@@KrunoEti code 10 comes up flashing
Gracias
you are welcome
I have a problem with the Xiaomi Pro 2 scooter. It lasts a long time when turned on and lasts a long time when turned off. After that, it started working on its own and I cannot change the mode or adjust the lighting. Is there a solution?
Not have problem like that, i rather contact or go to xiaomi official mehanics than say you to do something wrong
could be the controller board got little bit of moisture , i used isopropane alcohol to clean it and then hair dryer to get all the moisture out and it worked after that as new
i have electric scooter 1s i bought a thrrootle but the end part was abit smal and i dk if it was beucase the wrong throotle or my scooter broken
You need to order a throttle for 1s, maybe they are not same and different size
@@KrunoEti idk where from do you have any contact or massage app I really need help with this it was my sons birthday gift
@rdxbossbmxridding326 you have a link in description
Try punishing the accelerator (it worked for me)
How do you punish him?😁
i had the same problem but reseting it helped , no more error signal is shown .
problem is now that even fullt charged and in S mode scooter is not going above 20 km/h , before it was going at least 25 km . how can i fix that ?
That def broken, i will replace in your case, it is not too expensive at all
@@calminjarris4179thanks for the response , I replaced it - beeping stopped but now I have issue with speed - it’s not going over 20 km/h , before it was easily taking up to 27-28 km/h
I tried everything , battery is charged , throttle is new .
is it the same as Xiaomi Scooter 4 pro?
Not sure, but probably is the same
03:26 how you doing that? It's very hard part. I cannot put it back. Pls help
try with tweezers
@@KrunoEti yeah good idea. thank you. No I am driving with an open panel... If it's raining, the step will die directly 🤦♂️🤦♂️
O que eu não gosto dela é a bateria não dura tempo nellhum gasta muito dipressa
Battery is good enought that they advertise
Funziona anche con Xiaomi 4 Go?
Probably
Use 2 knives when taking off the handlebar it is easier
You can scratch it
On my m365 model, it shows me the 14 error but i can't even turn off the scooter, idk what to do..
Try to replace throttle
why won't you try Sport mode?
I tryed after fix
Pregunta mi scooter al prenderlo Realiza pidió y se apaga qué puede ser
What asks?
Anche dopo averlo caricato durante la notte, al mattino si è spento dopo 2 minuti. cosa posso fare ora
What program
No program
Hi can you help me how fix el-skoter error
How can I help you
I purchased a xiaomi electric scooter 4 lite brand new
I believe I've read the instructions correctly but it will not connect to my phone via Bluetooth and yet it will still go at at 10kmh I'm lost
it could also be that your wires are loose that was the case for me
Yep, thats the better scenario and also cheaper
I have the same problem, what is the solution?
Fix it
Change the display/screen easier
Scam. Just take a look to the red tap button of throttle censor it was the same 🤣🤣🤣
Why was scam, dont get it, it is real problem and it is real solved. Not one that have same issue and fix it😉
You scamer @@KrunoEti
Do I need to buy a new throttle sensor?
if you have same issue, yes
I just unplugged and plugged it and now it works@@KrunoEti
Como puedo reparar mi patin me marca error 16 porfavor
Error code 16: Incorrect MOS battery charge
Bro plz help me !
I think water went inside the screen was blank so i use isopropyl alcohol and scratch thebutton , the screen starts to appear but bro there is error 14 i tried alot
Change throttle accelerator
*replace
Amigo que le ases le cambias el gas o que????
No you replace and no problem
How to turn on lights in escooter
press once on power button
Do i need new parts
Hi there ive done everything else correct ,but throttle wont slide off
In what way wont slide?
@KrunoEti is there an alan key to undo on throttle as can't see it
@irishandproud1087 you replace with new throttle?
@KrunoEti no I can't get old one off
@irishandproud1087 did you remove plastic protector from handle bar and unscrew throttle?
I brought a new one and has that error? Doesn't accelerate? 😢😢😢😢
If you get new one and has same error you have warranty
You need to connect to the app.
My my number is showing 39
Number 39 is code for error for incorrect temperature from the battery sensor.
What about e3?
What whit e3?
Mine doesn't turn off
Let it run out off power, then change the display/ screen its easier.
How to fix it without taking it apart is there any solution?
If it is broken you need to replace, sometimes just need to open and disconnect connector there lose contact cuz of dust inside, so you can try in this way
@@KrunoEti Everytime i turn it on it just starts saying error 14 it does not change or does not move
Also do i use my same throttle or buy a new one?
@@KrunoEti if i factory reset my scooter will the error 14 go away?
@@KrunoEtialso how do i know if i have to replace it or just clean it?
Mine says 15
When the scooter controller senses abnormal brake performance it will show Error 15 and the scooter motor won't start.
A minha está a situação
What is problem?
Mine doesn't beep first
What code is showing, thats important?
My number is showing 21
Check the battery, motherboard and the connection between them.
And if i need to clean it
Than just clean it
Your scooter speed is 30km, how can i set my scooter 30 km?
You can move restriction and go 40
But sou will loose warranty
@@KrunoEtihow
@@KrunoEtido a video and Explain it
GGs
Ty
What problems of this
Of what problem, can you be more specific?
You know whats the bad news
All lights are on
what lights
Just tightit up
If it is not broken
Error13
Error code 13 is usually caused by moisture ingress and corrosion. Steps: Check the brake lever, the screen and the cable between them.
what if the little screws on the screen won't open
I can't get handlebar off
Put more pressure it is just screwdriver