Got a light on my Pet's dash board, saying that the right side has a problem. First of all I plan to swap RH and LH plugs. Surelly, then drive and check if the error changed. After all, probably, going to use your method to push a sensor closer to a tone ring. Will see. Yeah, you are right, a resistace of the sensor has to be checked first. Thanks for the video bro.
P.S. My case appeared to be much easier, swapped them, ran, the light is disappeared, put them back. Thats it. The problem is gone. Probably, the contacts were oxidited.
The next day after I watched this picked up a trailer that had a abs light on so climbed underneath found the abs sensor hanging by the wire behind the brake shoes it was a pain but stuck it back in and tapped with my extension and hammer until it bottomed out rolled 5 feet and light went out good thing too because it was the second day of dot safety blitz when I picked this particular trailer up you saved my butt Vlad !!!
Not much experience that I see. Not trying to talk negatively about him but he can’t even read a multi meter properly. He needs to jack it up and spin the wheels to test the sensors.Abs is my favorite part of my job. It’s the easiest lol by the way the resistance should show around 1.2 ohms not 1200. And beating on a plastic sensor housing is ridiculous. It is good that he is trying to fix it himself but with that being said it’s also extremely dangerous for other drivers on the highway for him to be half assing it himself. Bite the bullet and call a professional. It’s cheaper than the ticket and possibly killing somebody because your truck won’t stop in time! I could see fixing a light or something you know is easy and guaranteed to be working properly when you’re done. Leave the majority of it to a licensed and insured professional.
I fixed the sensor and tap the sennsor and trailer abs light was gone. i start driving on the road and hit pothole the abs light came on. i pushed the sensor back in light is off, next timr i start drive first bridge that i hit light comes On. it’s a driver side sensor on left side do u think is lose needs new one ?
Hello sir, I just bought trailer 2007 Vanguard equipped with abs system. The abs light is not working at all and i think someone turned off that light just to avoid getting pulled over, but actually i have trailer abs in the dash. Do u think the abs unit is bad ? i know the truck is not the issue cause i have newer trailer and abs works fine. When i check the power in the cables they all When i turn the ignition i hear some click in the trailer only once but that’s it. please help some advice is needed
HELP!! I checked the voltage On ABS unit and one side gives me 5.016 voltage and the other side gives me 0.168 voltage, Do u think abs unit needs to be replaced Thank You for taking the time making these videos and helping other drivers
Hey body, keep going to produce such videos, no music, no stupid humor, no poisoned smiles, the usful info only, like this one. Good luck!
))))) vlad, chto ti pil utrom?
Thank you for making this video. Also, the fuse for TRL ABS is L1 on the T680 in the under hood fuse box.
Thanks a lot, fixed my ABS light. Used flat head screw driver to clean and open more space on middle connector just as you showed us.
Thanks!
Got a light on my Pet's dash board, saying that the right side has a problem. First of all I plan to swap RH and LH plugs. Surelly, then drive and check if the error changed. After all, probably, going to use your method to push a sensor closer to a tone ring. Will see. Yeah, you are right, a resistace of the sensor has to be checked first. Thanks for the video bro.
P.S. My case appeared to be much easier, swapped them, ran, the light is disappeared, put them back. Thats it. The problem is gone. Probably, the contacts were oxidited.
I will follow the same step tomorrow on my trailer. Hope it's gonna do it. thanks for the vid. truly appreciate
This was the best explanation on you tube thanks so much Vlad
The next day after I watched this picked up a trailer that had a abs light on so climbed underneath found the abs sensor hanging by the wire behind the brake shoes it was a pain but stuck it back in and tapped with my extension and hammer until it bottomed out rolled 5 feet and light went out good thing too because it was the second day of dot safety blitz when I picked this particular trailer up you saved my butt Vlad !!!
Thank you very much Vlad. It was very helpful. God Bless You
Thank you for your video I recently replaced the brakes on my trailer I watched your video and tap in the sensors it works. Thanks again
Thank you. This video is going to be very helpful to troubleshoot mine
I was looking to get abs light on the tractor fixed, thanks for the video and your experience
Not much experience that I see. Not trying to talk negatively about him but he can’t even read a multi meter properly. He needs to jack it up and spin the wheels to test the sensors.Abs is my favorite part of my job. It’s the easiest lol by the way the resistance should show around 1.2 ohms not 1200. And beating on a plastic sensor housing is ridiculous. It is good that he is trying to fix it himself but with that being said it’s also extremely dangerous for other drivers on the highway for him to be half assing it himself. Bite the bullet and call a professional. It’s cheaper than the ticket and possibly killing somebody because your truck won’t stop in time! I could see fixing a light or something you know is easy and guaranteed to be working properly when you’re done. Leave the majority of it to a licensed and insured professional.
Thanks for keeping it simple
Good video!!
Thank you. GOD BLESS YOU.
It Worked!!! Great Job Sharing!!!
Thank you. Good job. Very helpful.
Awesome video. Thank you my Brother
Владимир спасибо огромное
Thank you for the videos you recorded.
It was very helpful.
Could you please make some videos about TCS system.
Thank you
Мужик красава! Займусь своим трейлером на выходных
I was an Avionics technician on the KC-10 for 13 years. You absolutely do NOT check resistance with power applied.
Thanks bud for this info..
Pretty simple, easy, thanks for the video
Thanks for sharing your knowledge.
Thank you sir
Thank you i learned something today
Thank you very much!!
Thanks for your help I’ll check my tomorrow
Thanks so much for your wonderful video
Thank you for you explanation
Great help man. Thank you
Thank you , my truck dashboard abs trailer not showing light , and light on trailer is yellow
Thanks bro it s a good information and amazing video tinx
thank you !
Thanks a lot dyadya Vlad
Very good video sir
thanks
Great video
Glad you enjoyed it
Great thank you it helps to find the problem
Thanks so much
thats right that is how to do it
Good video
Thanks 😊
My voltage is 25 volts at the abs unit . The trailer has two sensors, could it be the shortage in the unit ?
nice 😊 🙏
I fixed the sensor and tap the sennsor and trailer abs light was gone. i start driving on the road and hit pothole the abs light came on. i pushed the sensor back in light is off, next timr i start drive first bridge that i hit light comes On. it’s a driver side sensor on left side do u think is lose needs new one ?
clamping sleeve not holding on the place your sensor
Or you have problem with a hub bering wobbling ( Too much play in the wheel)
Hello sir,
I just bought trailer 2007 Vanguard equipped with abs system. The abs light is not working at all and i think someone turned off that light just to avoid getting pulled over, but actually i have trailer abs in the dash. Do u think the abs unit is bad ? i know the truck is not the issue cause i have newer trailer and abs works fine. When i check the power in the cables they all When i turn the ignition i hear some click in the trailer only once but that’s it. please help some advice is needed
check bulb and connector to it.
but i have trailer abs light on the dashboard. i replaced the bulb nothing s
it was sensor i tapped them and its working again thank u
Maybe I can close the gap like you did..👍
Yes you could, Most of the time the gap can be the problem with the ABS.
What about trucker ABS any ideas?
Have no idea.
HELP!!
I checked the voltage On ABS unit and one side gives me 5.016 voltage and the other side gives me 0.168 voltage,
Do u think abs unit needs to be replaced
Thank You for taking the time making these videos and helping other drivers
It should be same voltage, looks like need to be replaced.
@@VladMaktrucks
FIXED,
Abs light is gone after I Replaced ECM(abs unit) and I had to drive about 100 feet
Thanks again
👍👍👍👍🙏
Thank you sir
Great video
thank you sir