Does the indicator and brake input take 12v? I read on the ghozt page in1 is brake light/party mode via 12v. Does this mean I u can have the option of hooking up a switch to switch it to party mode if you not using the brake light function? If so how do I do this because I can't seem to figure it out software wise... Also i assume in1-in4 can all handle 12v?
I really hope you're still active on here. When I turn my parking lights on, the Blue Ghozt app is showing the brake light indicator and not the parking light indicator. Is this a wiring issue on the board itself? I didn't wire it, I bought it pre wired
Yes it sounds like it is miswired or misconfigured. Please reach out to who you purchased it from for assistance, as we don't know how they would have wired it.
2:05 - Which input is for parking lights, which is brake lights, and which ones are the turn signals? EDIT - Nevermind... Found it on the website... ghoztlighting.com/getting-started-blueghozt/ Although it would've been nice if he had specified which is which in the video... In1 - Brake signal input / party mode input (show mode activates via 12v) In2 - Parking/running lights signal input In3 - Left turn signal input In4 - Right turn signal input
yeah it's on our site, but just for reference here: GND - (required) Connect either of these to a ground +5V - (required) Connect to +5v or +12v power supply, depending on whether you are using 5v or 12v Neopixel LEDs +12V - (optional) Connect to a +12V supply for power switches on a BlueGhozt PLUS In1 - Brake signal input / party mode input (show mode activates via 12v) In2 - Parking/running lights signal input In3 - Left turn signal input In4 - Right turn signal input PS1, PS2, PS3, PS4 - (PLUS only) +12v outputs for 12v accessories
@@ghoztlighting Thank you... Just to make sure I get this straight before I start putting power to it..... I will need to give 5V to power the Blueghozt controller no matter what, but if I'm using 12V LEDs (which I will be), then I will also need to give 12 volts of power to +12V input (Blueghozt Lite version)? Thanks again for your help.
@@imdbtruth if you mean 12v Neopixels then you just apply 12v to the input that says "5v". I understand that is confusing, but it really is the "Neopixel positive input" which just has to match the Neopixel voltage. The 12v input is just for the PLUS model.
Ordered up my BlueGhozt plus, n was wondering. Are the sequential turn and DRL input modes 12v only? Previously with my vehicle, I had to use a relay to flip my negatively switched signal to a 12v positive.
I can’t get my ghozt module to read on my phone, I did the 12v to 5v, checked my power multiple times and even switched the power source and still nothing can’t figure out how to make it come on.
Hello. I’m having trouble with 1 of your controllers. All halos not sync,on is half off most of the time. How can I contact U. I’m sure it’s a simple fix. 1 that eludes me.
Hey question, I'm thinking about getting a box. but I'm trying to learn how to hook it up before I get it. I have 4 halos for low and high beams. How would I hooking it up. Cause I only see 2 connectors and the blueghozt
Are your halos equipped with addressable LED’s?(NeoPixel) Better yet can you post the exact rings you purchased this would make it much easier to help you.... as far as “how would i (you) hook it up?” Well sir, that all depends on wether you have the correct halos 👍🏼 let me know I’d love to help
Are you looking to have lights underneath? This comment is a little difficult to understand 🤔 also did you mean “valance?” Instead of “valentis🤨”. I’d like to help I just would need some more clarification in order to do so....🤷🏻♂️ if you can just post a link to an image of the section on the FRS/BRZ/GT86 that you want to mod and I can maybe help further
Most cars like an frs you can just buy what you need (custom headlights pre built) tail lights, ect.. and save yourself the trouble. Other people like myself are watching this video because some cars don't have pre built options.
It depends how many LEDs you are running, as this is limited to 350/side (700 total) - but yes it is possible and we support both white and red parking lights for front/rear!
Guess I gotta become a LED wiring expert now too if I wanna be a hotboi
Does the indicator and brake input take 12v?
I read on the ghozt page in1 is brake light/party mode via 12v. Does this mean I u can have the option of hooking up a switch to switch it to party mode if you not using the brake light function? If so how do I do this because I can't seem to figure it out software wise...
Also i assume in1-in4 can all handle 12v?
I really hope you're still active on here. When I turn my parking lights on, the Blue Ghozt app is showing the brake light indicator and not the parking light indicator. Is this a wiring issue on the board itself? I didn't wire it, I bought it pre wired
Yes it sounds like it is miswired or misconfigured. Please reach out to who you purchased it from for assistance, as we don't know how they would have wired it.
2:05 - Which input is for parking lights, which is brake lights, and which ones are the turn signals?
EDIT - Nevermind... Found it on the website... ghoztlighting.com/getting-started-blueghozt/
Although it would've been nice if he had specified which is which in the video...
In1 - Brake signal input / party mode input (show mode activates via 12v)
In2 - Parking/running lights signal input
In3 - Left turn signal input
In4 - Right turn signal input
yeah it's on our site, but just for reference here:
GND - (required) Connect either of these to a ground
+5V - (required) Connect to +5v or +12v power supply, depending on whether you are using 5v or 12v Neopixel LEDs
+12V - (optional) Connect to a +12V supply for power switches on a BlueGhozt PLUS
In1 - Brake signal input / party mode input (show mode activates via 12v)
In2 - Parking/running lights signal input
In3 - Left turn signal input
In4 - Right turn signal input
PS1, PS2, PS3, PS4 - (PLUS only) +12v outputs for 12v accessories
@@ghoztlighting Thank you... Just to make sure I get this straight before I start putting power to it..... I will need to give 5V to power the Blueghozt controller no matter what, but if I'm using 12V LEDs (which I will be), then I will also need to give 12 volts of power to +12V input (Blueghozt Lite version)?
Thanks again for your help.
@@imdbtruth if you mean 12v Neopixels then you just apply 12v to the input that says "5v". I understand that is confusing, but it really is the "Neopixel positive input" which just has to match the Neopixel voltage. The 12v input is just for the PLUS model.
@@ghoztlighting Okay. Now I understand. Thank you again for clarification, and also such quick responses.
Ordered up my BlueGhozt plus, n was wondering.
Are the sequential turn and DRL input modes 12v only?
Previously with my vehicle, I had to use a relay to flip my negatively switched signal to a 12v positive.
I can’t get my ghozt module to read on my phone, I did the 12v to 5v, checked my power multiple times and even switched the power source and still nothing can’t figure out how to make it come on.
It is the power in most cases but shoot us an email at support@ghoztlighting.com and you can send it back to us for testing/RMA if its defective
why is there no reverse input? Does it not have a reverse function?
this is the original v1, our v2 has a reverse input
@@ghoztlightingI see that in your website! I will be purchasing one of these without a doubt. Thank you for the reply!
Hello. I’m having trouble with 1 of your controllers. All halos not sync,on is half off most of the time. How can I contact U. I’m sure it’s a simple fix. 1 that eludes me.
How can I set up the turning signals? What wiring can I use? And do I just wire from the wire harness from ome lights on to the blueghozt?
Run through all the Getting Started videos, we cover all that.
Hey question, I'm thinking about getting a box. but I'm trying to learn how to hook it up before I get it. I have 4 halos for low and high beams. How would I hooking it up. Cause I only see 2 connectors and the blueghozt
Are your halos equipped with addressable LED’s?(NeoPixel) Better yet can you post the exact rings you purchased this would make it much easier to help you.... as far as “how would i (you) hook it up?” Well sir, that all depends on wether you have the correct halos 👍🏼 let me know I’d love to help
Could you walk me through what i would need to custom color sequential valentis for. 2016 frs? What would be needed from blue ghozt or ghozt lights
Are you looking to have lights underneath? This comment is a little difficult to understand 🤔 also did you mean “valance?” Instead of “valentis🤨”. I’d like to help I just would need some more clarification in order to do so....🤷🏻♂️ if you can just post a link to an image of the section on the FRS/BRZ/GT86 that you want to mod and I can maybe help further
Most cars like an frs you can just buy what you need (custom headlights pre built) tail lights, ect.. and save yourself the trouble. Other people like myself are watching this video because some cars don't have pre built options.
Hi bro. Let me know. Is the one module enough for two tail lights and headlights?
It depends how many LEDs you are running, as this is limited to 350/side (700 total) - but yes it is possible and we support both white and red parking lights for front/rear!
@@ghoztlighting thank you
What does the white info cord go to?
Where does this have to mounted? In vehicle away from any moisture?
If you don't insulate it from the weather then yeah we recommend installing inside the vehicle. Many people use potting material to weatherproof them!
I connected ws2812 strips but the colors that lights up is different then the color I select in the app same goes for my halos my drl strips etc
You have the wrong LEDs selected in the configuration tab; watch our tutorial videos for help on setting up the app!
Ghozt Lighting got it thanks overlooked that I jumped right into the fun stuff 👍🏻👍🏻
What led strip do you use
sirrr .. give awa for me please🥲🥲🥲