Hallo Thomas, das war wieder eine sehr interessante und aufwendige Arbeit. Deine Geduld möchte ich haben. Ich freue mich immer wieder dir bei der Arbeit zusehen zu können. Möge es lange so bleiben. Viele liebe Grüße und eine schöne neue Woche Christel ☺👍👌👏
Hallo Tom, if you cut glass in the future dip the glass cutter in a little white sprite and use a small brush with white sprite and run it along the surface of the glass , you will find it makes the cut easier. I was a glazier for over 35 years and used this method all the time good luck.
I would completely agree, for furniture that is, this has been my favorite channel for years now. However, there’s another channel called My Mechanics I would suggest you give a shot if you haven’t already. He does various tool restorations, so very detail orientated.
@@michaelsworld6292yes, the equivalent mastery but with metal...he makes new ones to paraphrase his famous caption! Have you seen Hand Tool Rescue? he's brilliant and hilarious. 😄
It hurts a little but it was nice to see Ella again. She always looked so sweet quietly checking on you. I bawled like a baby when you announced she had passed on. It reminded me of when I had lost my own dogs. I hope you are doing well Thomas. It does get easier with time but that hurt is still there.
I agree with Mr. Hollingsworth. I worked 5 summers in a commercial glass shop. The pros used mineral spirits to lubricate the cutter wheel during each cut. They used a shallow jar lid with a sponge inside. The sponge was soaked in mineral spirits. The pro would dip his cutter wheel before each cut. Long cuts were lightly traced along a straight edge before making the cut. Glass with an irregular surface was scored on the back (smooth) side. Large jobs called for a new cutter. Ragged edges can be sanded with a sanding block or a power sander. For large cuts the glass was scored one time with uniform pressure. Then the glass was then tapped on the underside with the cutter handle to initiate the crack. Then the drop piece was rolled down from the initial crack down the length of the cut. Cuts with a waste drop of less than 1 inch can be tricky. A good score should have a single continuous mark. Scoring glass more than once often causes bad breaks. Antique glass has variations and defects that challenge any glass cutter. Thank you for sharing your videos.
The patience you had getting that putty our of there Tom.. that glass cutting tool was fantastic. It was nice of her to help you. Loved seeing Ella again too. All the best as always. Kate x
I spend a lot of time as a glass cutter after high school. Working in a custom window shop with large sheets of glass and a tilt table. Cutters do wear out, dont be afraid to replace one if the score isnt right.
Some Scottish friends of ours in Northern Virginia lost several pieces in shipping from Scotland, and several more damaged - by inspectors, no less! Glad you could restore these doors. Beautiful work, as always, and kudos to the framer and your daughter!!
Hi Thomas Job Johnson, 😅🤣😂, because you Sir have the patience of Job. Quality work my friend. May you be blessed beyond measure! John here, from the back-roads of Northeastern Tennessee.
@@johnsonrestoration As a longtime, 36 years, photographer I absolutely agree. And as a believer, Galatians 6:9 - "And let us not be weary in well doing: for in due season we shall reap, if we faint not." Have a blessed day Thomas.
The first restoration was tedious for sure. Glad you had resources. And, 20 hours is actually fast I would say. Perfect restoration, as always. It’s great you are transparent and explain the steps and unforeseen situations.
You are so patient and meticulous with your work. Amazing how much experience information feedback arrives. I love your restoration projects in your videos. Thank you.
Tom, there's nothing I enjoy more in the morning than a cup of tea and watching one of your videos, your calm manner is a great way to start the day, thank you!
My father owned 3 acres of glasshouses and i learnt to cut glass at an early age. After you score the glass with the glass cutter if you then gentle tap the glass along the cut it completes the fracturing along the cut enabling a clean break.
Love watching your process and how when you hit a snag, you just work through it patiently. Your videos helped me feel confident enough to reglue a set of antique chairs that have been sitting in my dining room waiting to be fixed for 5 years! Thanks, Tom!
Hi Scott! First comment! Every time I cut glass I feel like I'm starting all over again. But I know I'm getting better. I finally got a professional glass "cutter". Those cheap ones from the hardware store don't work that well. You need to be confident, and that is tough!
I'm not sure if I saw you using a cutting oil when trying to cut the glass with the tool you have, but my dad told me that kerosene works very well for cutting, it helps the glass to cut cleanly
Hi Tom, I love your TH-cam videos very educational and informative. I am a cabinet maker with almost 40 years experience from Gilmanton New Hampshire . What I appreciate most among your many talents is the ability to restore a piece of furniture and maintain the original finish. That is an art within itself and in my opinion you have mastered it . Please keep up the good work it's always a pleasure to watch you do your magic. By the way I'm curious do you know if you have a brother named Larry David
Hi James! Thank you! Many have commented on Larry David over the years! I can only hope that's a good thing. But I really appreciate positive feedback from fellow tradespeople, it means a lot to me. Come visit if you are ever in the area!
Hello how are you Thomas, I am writing to you from far away, my small country Uruguay... I follow your restorations on the channel, they are incredible... could you make a video showing the workshop and its machines? That workplace is beautiful. .thank you totally
Haha I love how completely confident you became during the course of this project in cutting glass. From your first awkward attempts to becoming a glass cutting master! In the UK, glass window restorers use the same tool and techniques that you have used, so well done. It was lovely seeing Ella again.
At the start I admit I was wondering how you were going to cut the larger pieces of glass because I know it is so hard without specialized tools. I saw you using that little scorer and I thought, "Wow, that is going to be tough". I'm so happy you found a fellow professional.
Hi Thomas just want to says thanks ! Watching your videos at the end of the day is almost therapy for me. Its feels so comfortably and relaxing seeing you working. I hope one day i have some portion of your patience. Thanks for sharing it. Its inspiring.
A lovely restoration Tom, and being a Scot it is always a double pleasure to see a local piece taking pride of place so far away. I must admit to holding my breath on a few occasions as you shaped the glass, especially the octagonal piece. Thanks for sharing your skills with us.
It looks like you used some sort of film to keep the broken glass from falling to pieces while you were removing it. If so, it's a great idea! It keeps the mess to a minimum, and it can even help with making a template. If so, what is the film, cling wrap? Also, fingers are the best caulking and putty tools never invented. It's a messy job, but when it's done - what a satisfying project! Great work!
Your videos are always the highlight of my day Michael Hollingsworth is spot on about the mineral spirits The cutter you are using will actually hold the spirts in the shaft and dispense it on the glass as you score it and as others have pointed out you want to snap the glass from the end rather than the middle I prefer starting on the side that the cutter has run off as the score goes all the way to the edge there
Enjoyed the videos Tom. You chose the right title. It is so satisfying when you score glass and it breaks in the right place. That second piece you did was a big puzzle to get back together before the glass went in. I guess you have seen some antiques that the glass was glazed with wax not glazing compound. You take care and God bless.
Awsome ! You really have a talent for "Dramatic Furniture !" Every time you upload your work is like watching " As the wood turns" soap lol . Great patience!👍. Beautiful hutch.
Both of these lovely pieces of furniture turned out perfectly - as always. 👍🏻 I love learning from a true artist at his craft, and I have acquired more usable knowledge from watching Mr. Johnson's videos than any of the other excellent firniture restoration professionals on TH-cam. Thank you Thomas Johnson!!!!! A few odd FYI tidbits of wisdom for any glass cutting nerdy newbies ... A light cutting oil applied with the cutting wheel always helps glass break more cleanly. All glass, but especially softer antigue type glasses, have the quirky property of being semi-fluid. Over time, old window panes and door lites will flow into being thicker at the bottom. It's amazing to observe this effect in antique windows and doors. This semi-fluid behavior also means that cuts made in glass will heal surprisingly fast after being cut, especially if oil isn't used and if the breaking pressure isn't applied quickly after making a cut. Healing means the cut edges flow back together and fill in the cut over time. Healing is never a completely even process. It's always best to use oil to slow the heal, use a sharp wheel, cut with even firm pressure pushing AWAY from you for more consistent control of pressure, and snap the cut immediately using a straight edge, parallel action grozier pliers, or glass cut-running pliers. The glass cutter Mr. Johnson is using is a primo glass cutter with a reservoir in the handle for cutting oil, and is a worthy investment for anyone serious about working in stained glass or cutting window glass frequently. Sometimes residue will block the wicking action of this type of tool, resulting in a dry uneven cut. A dry cut also shortens the life of the cutting wheel. The remedy is to periodically clean the cutter head with mineral spirits, especially if the cutter isn't used often. A dull cutting wheel also results in rough, uneven cuts. Some glass is harder and denser than other types. One example of harder glass is multi-color opal glasses which are known for being more difficult to cut due to multiple color layers and erratic grain. Hard glass can dull a cutting wheel more quickly. Antique window glass, the lovely rippled glass in old home windows and in old antiques such as those featured, is generally very soft but with somewhat variable grain and thickness throughout. The best approach for curved cuts in glass is to apply firm even pressure with a well oiled sharp cutter, and quickly apply even pressure along the break using breaking or cut running pliers. For straight cuts, the edge of a table or a raised straight edge works best to apply even pressure along the cut. Modern window glass is often tempered, and demands very firm even pressure along a cut to break straight by hand, but even doing so may still result in surprises. A modern cutting machine is safer bet for long straight cuts on modern glass. Cutting machines like the one this framing shop has are costly, but a wise investment for making a lot of long straight cuts, unless a person enjoys being frustrated and having a big box of odd shaped pieces of fractured glass that did not break correctly the first time - or second time, or third time ... .
Sorry to disappoint, but the story of antique glass (or indeed any glass) flowing is just a myth. See for example Dutra Zanotto, E. _Do cathedral glasses flow?_ in American Journal of Physics 66:392-395 (May 1998), or Borja, L. _Shattering the myth of fast-flowing medieval glass_ in Material Research Society Bulletin, Cambridge University Press, October 2017. The Dutra Zanotto paper actually explains why some medieval glass is thicker at the bottom than the top, and it's because of the way in which it was made, not because it flows due to gravity. The viscosity of glass - even soft medieval glass - is such that it will flow by a few nanometres in a billion years.
@@johnsonrestoration That is _absolutely_ not true! The amount of tips, tricks, techniques and just plain old patience that we all learn from watching your videos is staggering.
Thank you for the video. I enjoyed and learned a coupled of things that I may be able to put to use in a future project of my own, nicely done and crafted sir.
Love watching you work. A friend of mine who does a bit of lead lighting made a couple of panels for our home. Cutting glass sure is skill I admire. I did all the grinding. It’s great to have many lessons as you teach as you work. Beautiful results on all the pieces. I love all the details you show, like the cambric strips in the corners.
I still have one of those glass cutters like yours. I first learned to use them when I worked in retail at W.T.Grants. Do you recall seeing shelves with glass partitions that were mounted vertically to divide spaces for products? We cut glass to fit the metal shelves, and some departments had glass shelves. I got fairly proficient at cutting glass. It was fun.
Some years ago when my wife and I bought a condo on Portland's West End, we had the Frame Shop on Longfellow Square do a number of framing jobs for us. I got to know the owner, Tim Hussey quite well , he was a perfectionist! I'm aware of the The Little Falls Frame Shop as she bought Tim's inventory when he closed up. Now I'm going to have stop by the next time we are in Maine - I helped Tim find a small Delta disk sander and Ulmia miter box. A glass machine is the way to go - pricey but fortunately a friend has one he bought from a hardware store going out of business - does a great job.
I love the forensic analysis of a piece during deconstruction. One can learn a lot, both in the mistakes made and the good done, such as the reinforcement fabric
@@johnsonrestoration As it happens, my sister and I have recently selected a Celtic Cross design for our parents' headstone so maybe that's why it came to mind.
Hi Tom. I love your videos, they very soothing and your work is impeccable. You're like the Bob Ross of furniture restoration! I've learned so much from you. I noticed your left hand looked pretty bruised, whatever happened, I hope it's feeling better now :)
I believe the small fabric is for strength,as you thought,....but also as a cushion for the thin glass to help absorb the stress of hard accidental closing
I really appreciate you putting together these tutorial videos Tom, its good to see the nuances and slight variations in approach with each job - even though some might say "they are all the same". Biggest concern however was your left hand in the first video...eek that looked painful! But you were a champ working through it💪 Take care of yourself - there's one only one of you in the world🤩
Obrigado Tom por mais este excelente vídeo. Lindo trabalho! Aprendo sempre assistindo seus fabulosos trabalhos de restauração. Já cortei vidro algumas poucas vezes. Não é tão fácil quanto parece!
Putty is an amazing compound, Tom. Is it a mix of clay and linseed oil? Clever that it can be softened with gentle heat too. Your local framing friend has great equipment for cutting larger pieces of glass. An interesting fact about old glass is that over the centuries it will flow microscopiaclly. The Kings College chapel in Cambridge, England, and built in the fifteenth century has some glass which is thicker at the lower end than at the upper end which shows that gravity makes it flow downwards very slowly.
The 'flow' of glass is actually an urban myth, certainly over a few millennia (never mind 600 years) - see for example Dutra Zanotto, E. _Do cathedral glasses flow?_ in American Journal of Physics 66:392-395 (May 1998), or Borja, L. _Shattering the myth of fast-flowing medieval glass_ in Material Research Society Bulletin, Cambridge University Press, October 2017. The Dutra Zanotto paper actually explains why some medieval glass is thicker at the bottom than the top, and it's because of the way in which it was made, not because it flows due to gravity.
Thank you! I'm not sure what it's made of, but that sounds plausible! Interesting about the glass, and dlevi67's response. I have a feeling he knows what he's talking about!
To remove smudges from the glass, sprinkle on some dry plaster of paris and use a soft dry brush to swirl it around. It soaks up the oils and makes final cleaning much easier.
I've never been able to cut glass. I found it cheaper to just order the glass to the demensions I need. Love all the cabinets. Excellent work, great video.
That was brilliant Tom ! The one thing I cannot do is cut glass. I just break glass - I think I try too hard and am nervous of it. I see you put oil before your glass cutter - never heard of that - seems to work for you, so maybe I'll try it out on some old piecse of glass, to practice. The fabric at the corners of the mullions was a good idea and actually seems logical when you think of it. Thanks Tom for sharing yet another of your many skills with us. Your patience is fantastic - you're such a pleasure to observe. Take care 🙂
You're welcome! Yes, practice! The main thing I learned is to get a professional cutter. If you do use the cheap ones at the hardware store, always buy a new one for each job. They do not last long
Hallo Thomas, das war wieder eine sehr interessante und aufwendige Arbeit. Deine Geduld möchte ich haben. Ich freue mich immer wieder dir bei der Arbeit zusehen zu können. Möge es lange so bleiben. Viele liebe Grüße und eine schöne neue Woche Christel ☺👍👌👏
Danke Christel! Ich hoffe, Sie haben auch eine gute Woche (oder jetzt sollte ich sagen Wochenende)!
Another great one to watch, after lunch, hiding indoors from this unusually warm afternoon sun...rr Normandy, France
Thanks!
Hallo Tom, if you cut glass in the future dip the glass cutter in a little white sprite and use a small brush with white sprite and run it along the surface of the glass , you will find it makes the cut easier. I was a glazier for over 35 years and used this method all the time good luck.
very true. My father also used this method.
White spirit? Or sprite? What is sprite? Not the drink?!
I did wonder if wetting the glass would help, as the liquid helps cracks propagate faster.
Thank you! Sounds like good advice. Like others I'm wondering what White Sprite (or spirit?) is. Alcohol?
@@johnsonrestoration Hallo Tom! I think it's known as mineral spirits or plain old paint thinner in the US
I honestly believe you are the most patient person doing restorations on all of TH-cam! Always enjjoy watching you work!! Age 73 retired carpenter.
I would completely agree, for furniture that is, this has been my favorite channel for years now. However, there’s another channel called My Mechanics I would suggest you give a shot if you haven’t already. He does various tool restorations, so very detail orientated.
@@michaelsworld6292yes, the equivalent mastery but with metal...he makes new ones to paraphrase his famous caption!
Have you seen Hand Tool Rescue? he's brilliant and hilarious. 😄
Thank you! It means a lot to me coming from a fellow tradesman!
Thanks! I'll check that out!
It’s so lovely that we still get to see Ella occasionally ❤ 👼
Thanks! I know, I wasn't sure how I would react but I like it
Beautiful … professional … attention to detail… refreshing …😊
Thank you very much!
It hurts a little but it was nice to see Ella again. She always looked so sweet quietly checking on you. I bawled like a baby when you announced she had passed on. It reminded me of when I had lost my own dogs. I hope you are doing well Thomas. It does get easier with time but that hurt is still there.
Thank you Kate, I appreciate it. I too wasn't sure how I would feel seeing Ella but I'm glad when I do. I think about her everyday
Glazing windows was my least favorite part of old window restoration. Great job as always, Tom!
Thanks! I like it when it goes well!
The right tools for the job can make all the difference
Absolutely! There seems like there is a specific tool for just about everything!
Whew! I was holding my breath there for a while, great job! Thank you!
Me too! Thanks!
I agree with Mr. Hollingsworth. I worked 5 summers in a commercial glass shop. The pros used mineral spirits to lubricate the cutter wheel during each cut. They used a shallow jar lid with a sponge inside. The sponge was soaked in mineral spirits. The pro would dip his cutter wheel before each cut. Long cuts were lightly traced along a straight edge before making the cut. Glass with an irregular surface was scored on the back (smooth) side. Large jobs called for a new cutter. Ragged edges can be sanded with a sanding block or a power sander. For large cuts the glass was scored one time with uniform pressure. Then the glass was then tapped on the underside with the cutter handle to initiate the crack. Then the drop piece was rolled down from the initial crack down the length of the cut. Cuts with a waste drop of less than 1 inch can be tricky. A good score should have a single continuous mark. Scoring glass more than once often causes bad breaks. Antique glass has variations and defects that challenge any glass cutter. Thank you for sharing your videos.
Thanks! Good advice!
We cheered when the last piece of the octagon came off. Thank you for your video.
Thanks! That's great!
This glass cabinet turned out impeccable with the Blenheim glass. Great job Tom! Actually, all three glass jobs were good!
Thanks! Yes, the Bendheim Glass is a life saver!
The patience you had getting that putty our of there Tom.. that glass cutting tool was fantastic. It was nice of her to help you. Loved seeing Ella again too. All the best as always. Kate x
Thanks 👍 Yes, I like seeing Ella too...
I spend a lot of time as a glass cutter after high school. Working in a custom window shop with large sheets of glass and a tilt table. Cutters do wear out, dont be afraid to replace one if the score isnt right.
Thanks! It took a lot of failures to figure that out
Some Scottish friends of ours in Northern Virginia lost several pieces in shipping from Scotland, and several more damaged - by inspectors, no less! Glad you could restore these doors. Beautiful work, as always, and kudos to the framer and your daughter!!
Thank you! I'm so sorry for your friends! I hate it when people don't respect other's belongings
Hi Thomas Job Johnson, 😅🤣😂, because you Sir have the patience of Job. Quality work my friend. May you be blessed beyond measure! John here, from the back-roads of Northeastern Tennessee.
Thank you John! I like being patient! It's the fastest way to get to the end
@@johnsonrestoration As a longtime, 36 years, photographer I absolutely agree. And as a believer, Galatians 6:9 - "And let us not be weary in well doing: for in due season we shall reap, if we faint not." Have a blessed day Thomas.
The first restoration was tedious for sure. Glad you had resources. And, 20 hours is actually fast I would say. Perfect restoration, as always. It’s great you are transparent and explain the steps and unforeseen situations.
Thanks! Tedious yes, but I learned a lot!
Nice, Tom. I liked the Ella flashback.
Me too! Thanks
I was fascinated by the whole process. Thanks for adding the metric measurements too 😊
You’re welcome! 😊
You are so patient and meticulous with your work. Amazing how much experience information feedback arrives.
I love your restoration projects in your videos.
Thank you.
You're welcome! And yes, I learn a lot from the comments
Knowing when it’s wiser to use an expert is an art!
Great job.
Very true! Thanks!
We all knew at the start it would turn out perfect. The fun and satisfaction for us is watching you get there! Thanks, Tom!
You're welcome!
Tom, there's nothing I enjoy more in the morning than a cup of tea and watching one of your videos, your calm manner is a great way to start the day, thank you!
Me too, good morning, UK time🫖👍😄
You're welcome! I love to hear that
Thanks!
My father owned 3 acres of glasshouses and i learnt to cut glass at an early age. After you score the glass with the glass cutter if you then gentle tap the glass along the cut it completes the fracturing along the cut enabling a clean break.
Thanks! I can see you have a lot of experience!
Love watching your process and how when you hit a snag, you just work through it patiently. Your videos helped me feel confident enough to reglue a set of antique chairs that have been sitting in my dining room waiting to be fixed for 5 years! Thanks, Tom!
You're welcome! Good luck with those chairs!
Thanks for the glass cutting lesson Tom. I always get nervous when cutting glass. I like your approach of doing the simple ones first! Scott
Hi Scott! First comment! Every time I cut glass I feel like I'm starting all over again. But I know I'm getting better. I finally got a professional glass "cutter". Those cheap ones from the hardware store don't work that well. You need to be confident, and that is tough!
Great video, thank you for just being yourself.
You're welcome!
The usual attention to detail is such a pleasure
Thank you!
Thanks Tom, another great video, I always find cutting glass to be a real pane!!! Hope you're well see you on the next one
Good one! Thanks
Another fascinating one, Tom! As you were working, I was wondering how the hell they make mullions that fine LOL! Thanks.
That is a very good question! I can't imaging...
Thanks for another masterclass Tom. A post from you always makes my Friday better.
That's great! Thanks
Your daughter is in my hometown. And a local framer that I used to use recently retired. So I’m glad to hear that there’s someone else I can use.
Great! Here's her website: www.emcollier.com/
The visual joke on the thumbnail (a pic of you and the words “100 years old”) was a good one!😂
Thanks! Haven't been too many comments on that!
Another masterful repair by Tom! Plus I am Scots, from the Clan Gunn! So that is cool repairing the heritage of the homeland ... XO
Thanks! Glad to do it!
Lovely work as usual. Cutting glass is a leap of faith each time. Not for the feint hearted.
So true! Thanks!
You must have the patience of Job! I really enjoy your videos. Thank you!
You're welcome!
I'm not sure if I saw you using a cutting oil when trying to cut the glass with the tool you have, but my dad told me that kerosene works very well for cutting, it helps the glass to cut cleanly
Thanks! There was a bit of oil on the cutter
Hi Tom, I love your TH-cam videos very educational and informative. I am a cabinet maker with almost 40 years experience from Gilmanton New Hampshire . What I appreciate most among your many talents is the ability to restore a piece of furniture and maintain the original finish. That is an art within itself and in my opinion you have mastered it . Please keep up the good work it's always a pleasure to watch you do your magic. By the way I'm curious do you know if you have a brother named Larry David
Hi James! Thank you! Many have commented on Larry David over the years! I can only hope that's a good thing. But I really appreciate positive feedback from fellow tradespeople, it means a lot to me. Come visit if you are ever in the area!
So great to see you collaborate with your daughter and another local artisan.
Yes, I liked that too! Thanks
Hello how are you Thomas, I am writing to you from far away, my small country Uruguay... I follow your restorations on the channel, they are incredible... could you make a video showing the workshop and its machines? That workplace is beautiful. .thank you totally
Again - you're welcome!
@@johnsonrestoration agradecido y feliz por su respuesta,Thomas..
Haha I love how completely confident you became during the course of this project in cutting glass. From your first awkward attempts to becoming a glass cutting master! In the UK, glass window restorers use the same tool and techniques that you have used, so well done. It was lovely seeing Ella again.
Thanks! It is good seeing her!
Superb glass-o-rama, Tom. Those Scottish mullions remind me of kumiko panels.
Thanks! They do!
Amazing craftsmanship
Thank you!
Love the metric Tom, keep it up!
Thanks, will do!
As has been said, you’ve got the patience of a saint. Thanks again for this informative episode. 👏😁🇦🇺
You're welcome!
You make cutting glass look so easy!
Oh wow! I'm glad it looked like that! By the time I was done I had it down
What a treat to see Ella beside you once again. You must miss her a lot.
Oh I do! Everyday. I want to hug her again!
Great work as always, Tom. ❤
Thanks!
At the start I admit I was wondering how you were going to cut the larger pieces of glass because I know it is so hard without specialized tools. I saw you using that little scorer and I thought, "Wow, that is going to be tough". I'm so happy you found a fellow professional.
Yes, it was bad! Thanks goodness for Leah!
Hi Thomas just want to says thanks ! Watching your videos at the end of the day is almost therapy for me. Its feels so comfortably and relaxing seeing you working. I hope one day i have some portion of your patience. Thanks for sharing it. Its inspiring.
You're welcome!
A lovely restoration Tom, and being a Scot it is always a double pleasure to see a local piece taking pride of place so far away. I must admit to holding my breath on a few occasions as you shaped the glass, especially the octagonal piece. Thanks for sharing your skills with us.
You're welcome! I was definitely holding my breath!
It looks like you used some sort of film to keep the broken glass from falling to pieces while you were removing it. If so, it's a great idea! It keeps the mess to a minimum, and it can even help with making a template. If so, what is the film, cling wrap?
Also, fingers are the best caulking and putty tools never invented. It's a messy job, but when it's done - what a satisfying project! Great work!
Thanks! The owner had done that, and yes, it was a good idea
It was just clear plastic tape for boxes
Your patience and skills are inspiring. Thanks for sharing. 💚👽
You're welcome!
Your videos are always the highlight of my day
Michael Hollingsworth is spot on about the mineral spirits
The cutter you are using will actually hold the spirts in the shaft and dispense it on the glass as you score it and as others have pointed out you want to snap the glass from the end rather than the middle
I prefer starting on the side that the cutter has run off as the score goes all the way to the edge there
Thanks! That's good advice! Another commenter was saying a similar thing
It's always a pleasure to watch a true craftsman work
Thank you!
Enjoyed the videos Tom. You chose the right title. It is so satisfying when you score glass and it breaks in the right place. That second piece you did was a big puzzle to get back together before the glass went in. I guess you have seen some antiques that the glass was glazed with wax not glazing compound. You take care and God bless.
Thanks Ron! No, I haven't seen one done with wax...sounds interesting
A masterclass in glass replacement in period furniture. A real treat and so much learned from a true master of his craft. Thank you.
You're welcome!
Thank you Tom always enjoyable!
My pleasure!
Beautiful job, Tom. You have the patience of Job and the tenacity of a Marine raider!
Thanks! 👍I like that!
Awsome ! You really have a talent for "Dramatic Furniture !" Every time you upload your work is like watching " As the wood turns" soap lol . Great patience!👍. Beautiful hutch.
Thank you so much! 😀 I need to use "as the world turns" or a variation in a title!
The few times I replaced glass, I made putty snakes, laid them on the glass/frame interface and worked them in by hand.
Thanks! Yes, I have done that too, didn't work here because the frame was so small
I have PTSD from re-puttying the windows in my home with my father when I was young. He (and you) have infinitely more patience than I!
Thanks! Ah, the memories!
Praca wymagająca szczególnej dokładności i delikatności. Najwięcej pracy wymagało dokładne nałożenie kitu do szyb. Mistrz Thomas jak zwykle doskonale.
Dziękuję!
Glass gives me the shivers!! Awesome job, Tom.
Me too! Thanks!
I have not worked with glass before but now my old pie safe is on the list. That was great sir thank you.👍
You're welcome! Good luck!
Simply stunning .
Thank you!
It’s fascinating watching you repair old pieces! Love your channel. This video with the glass repair was amazing!
Thank you!
Both of these lovely pieces of furniture turned out perfectly - as always. 👍🏻
I love learning from a true artist at his craft, and I have acquired more usable knowledge from watching Mr. Johnson's videos than any of the other excellent firniture restoration professionals on TH-cam. Thank you Thomas Johnson!!!!!
A few odd FYI tidbits of wisdom for any glass cutting nerdy newbies ... A light cutting oil applied with the cutting wheel always helps glass break more cleanly. All glass, but especially softer antigue type glasses, have the quirky property of being semi-fluid. Over time, old window panes and door lites will flow into being thicker at the bottom. It's amazing to observe this effect in antique windows and doors. This semi-fluid behavior also means that cuts made in glass will heal surprisingly fast after being cut, especially if oil isn't used and if the breaking pressure isn't applied quickly after making a cut. Healing means the cut edges flow back together and fill in the cut over time. Healing is never a completely even process. It's always best to use oil to slow the heal, use a sharp wheel, cut with even firm pressure pushing AWAY from you for more consistent control of pressure, and snap the cut immediately using a straight edge, parallel action grozier pliers, or glass cut-running pliers.
The glass cutter Mr. Johnson is using is a primo glass cutter with a reservoir in the handle for cutting oil, and is a worthy investment for anyone serious about working in stained glass or cutting window glass frequently. Sometimes residue will block the wicking action of this type of tool, resulting in a dry uneven cut. A dry cut also shortens the life of the cutting wheel. The remedy is to periodically clean the cutter head with mineral spirits, especially if the cutter isn't used often. A dull cutting wheel also results in rough, uneven cuts. Some glass is harder and denser than other types. One example of harder glass is multi-color opal glasses which are known for being more difficult to cut due to multiple color layers and erratic grain. Hard glass can dull a cutting wheel more quickly.
Antique window glass, the lovely rippled glass in old home windows and in old antiques such as those featured, is generally very soft but with somewhat variable grain and thickness throughout. The best approach for curved cuts in glass is to apply firm even pressure with a well oiled sharp cutter, and quickly apply even pressure along the break using breaking or cut running pliers. For straight cuts, the edge of a table or a raised straight edge works best to apply even pressure along the cut.
Modern window glass is often tempered, and demands very firm even pressure along a cut to break straight by hand, but even doing so may still result in surprises. A modern cutting machine is safer bet for long straight cuts on modern glass. Cutting machines like the one this framing shop has are costly, but a wise investment for making a lot of long straight cuts, unless a person enjoys being frustrated and having a big box of odd shaped pieces of fractured glass that did not break correctly the first time - or second time, or third time ... .
Sorry to disappoint, but the story of antique glass (or indeed any glass) flowing is just a myth. See for example Dutra Zanotto, E. _Do cathedral glasses flow?_ in American Journal of Physics 66:392-395 (May 1998), or Borja, L. _Shattering the myth of fast-flowing medieval glass_ in Material Research Society Bulletin, Cambridge University Press, October 2017.
The Dutra Zanotto paper actually explains why some medieval glass is thicker at the bottom than the top, and it's because of the way in which it was made, not because it flows due to gravity. The viscosity of glass - even soft medieval glass - is such that it will flow by a few nanometres in a billion years.
Thank you! Very good advice. I am saving all this advice and putting it with my glass cutting kit!
I am learning a lot more from my viewers (especially you!) than they are learning from me!
@@johnsonrestoration That is _absolutely_ not true! The amount of tips, tricks, techniques and just plain old patience that we all learn from watching your videos is staggering.
Really nice look at irregular glazing! Fascinating!
Thank you!
Learned a lot from this video, thanks
You're welcome!
Thank you for the video. I enjoyed and learned a coupled of things that I may be able to put to use in a future project of my own, nicely done and crafted sir.
Glad it was helpful! Thanks!
Very nice videos on antique glass replacement. Excellent work. Thanks for sharing ❤
You're welcome!
another wonderful video! and just in time for me as I have half a dozen window panes to fix thanks to my ineptness with the heat gun 🙂
Thanks! Yes, good luck!
Love watching you work. A friend of mine who does a bit of lead lighting made a couple of panels for our home. Cutting glass sure is skill I admire. I did all the grinding. It’s great to have many lessons as you teach as you work. Beautiful results on all the pieces. I love all the details you show, like the cambric strips in the corners.
Thanks Allison!
I still have one of those glass cutters like yours. I first learned to use them when I worked in retail at W.T.Grants. Do you recall seeing shelves with glass partitions that were mounted vertically to divide spaces for products? We cut glass to fit the metal shelves, and some departments had glass shelves. I got fairly proficient at cutting glass. It was fun.
Thanks! Yes, cutting a lot of glass like that you must have really got it down. Every time I cut glass I have to start over again!
Some years ago when my wife and I bought a condo on Portland's West End, we had the Frame Shop on Longfellow Square do a number of framing jobs for us. I got to know the owner, Tim Hussey quite well , he was a perfectionist! I'm aware of the The Little Falls Frame Shop as she bought Tim's inventory when he closed up. Now I'm going to have stop by the next time we are in Maine - I helped Tim find a small Delta disk sander and Ulmia miter box.
A glass machine is the way to go - pricey but fortunately a friend has one he bought from a hardware store going out of business - does a great job.
Thanks! You should definitely visit the Little Falls shop. But even a machine doesn't help with those little angled cuts!
Nice work Thomas.
Thanks!
Thank you Tom!
You're welcome!
I love the forensic analysis of a piece during deconstruction. One can learn a lot, both in the mistakes made and the good done, such as the reinforcement fabric
Thanks! Yes, so true!
Thank you Tom, nice compilation of your different experiences with glass. So patient.👍👏
Glad you enjoyed it!
Always enjoy your videos! You are a true craftsman.
Thank you very much!
Incredible job Sir! Very nice indeed!
Thank you!
Always enjoyably impressed by your skill, but this one...well, wow. Now both cabinets will continue to age beautifully.
Thanks!
Tom, after you score the glass line up the white line of the running pliers on the score line and squeeze. That's why the pliers have that white line.
Oh! I get it! I will try that in the future
super jobs, I never could cut glass, but they look just like new!!!
Thanks! I am still learning. It's like I have to learn from the beginning every time
The layout of the glazing panels is reminiscent of the Celtic Cross that was popular in areas of Scotland and northern England in years gone by.
Thank you! I was wondering about that design - you see it a lot.
@@johnsonrestoration As it happens, my sister and I have recently selected a Celtic Cross design for our parents' headstone so maybe that's why it came to mind.
Hi Tom. I love your videos, they very soothing and your work is impeccable. You're like the Bob Ross of furniture restoration! I've learned so much from you. I noticed your left hand looked pretty bruised, whatever happened, I hope it's feeling better now :)
Thanks! I have a bruised fingernail - not bad though!
Nice video. Great to remember dogger again.
Thanks! I miss her!
Another great teaching session, thank you Thomas.
You're welcome!
I believe the small fabric is for strength,as you thought,....but also as a cushion for the thin glass to help absorb the stress of hard accidental closing
Thanks! Yes, especially since there was no room for glaze
I really appreciate you putting together these tutorial videos Tom, its good to see the nuances and slight variations in approach with each job - even though some might say "they are all the same". Biggest concern however was your left hand in the first video...eek that looked painful! But you were a champ working through it💪 Take care of yourself - there's one only one of you in the world🤩
Thank you! I don't remember anything with my hand!
Obrigado Tom por mais este excelente vídeo.
Lindo trabalho!
Aprendo sempre assistindo seus fabulosos trabalhos de restauração.
Já cortei vidro algumas poucas vezes.
Não é tão fácil quanto parece!
De nada! Com certeza não é! É preciso muita prática
Putty is an amazing compound, Tom. Is it a mix of clay and linseed oil? Clever that it can be softened with gentle heat too. Your local framing friend has great equipment for cutting larger pieces of glass. An interesting fact about old glass is that over the centuries it will flow microscopiaclly. The Kings College chapel in Cambridge, England, and built in the fifteenth century has some glass which is thicker at the lower end than at the upper end which shows that gravity makes it flow downwards very slowly.
The 'flow' of glass is actually an urban myth, certainly over a few millennia (never mind 600 years) - see for example Dutra Zanotto, E. _Do cathedral glasses flow?_ in American Journal of Physics 66:392-395 (May 1998), or Borja, L. _Shattering the myth of fast-flowing medieval glass_ in Material Research Society Bulletin, Cambridge University Press, October 2017.
The Dutra Zanotto paper actually explains why some medieval glass is thicker at the bottom than the top, and it's because of the way in which it was made, not because it flows due to gravity.
Thank you! I'm not sure what it's made of, but that sounds plausible! Interesting about the glass, and dlevi67's response. I have a feeling he knows what he's talking about!
So interesting! Another myth bites the dust
To remove smudges from the glass, sprinkle on some dry plaster of paris and use a soft dry brush to swirl it around. It soaks up the oils and makes final cleaning much easier.
Wow - what a good idea! Thanks
I've never been able to cut glass. I found it cheaper to just order the glass to the demensions I need. Love all the cabinets. Excellent work, great video.
Thanks! I used to do that, but here in Maine I couldn't find anyone. I like learning any way
I cannot tell you how many pieces of glass I broke.
Keep up the great work
I didn't show all the times I screwed up!
Another brilliant job. Well done 👏👏❤️
Thank you!
That was brilliant Tom ! The one thing I cannot do is cut glass. I just break glass - I think I try too hard and am nervous of it. I see you put oil before your glass cutter - never heard of that - seems to work for you, so maybe I'll try it out on some old piecse of glass, to practice. The fabric at the corners of the mullions was a good idea and actually seems logical when you think of it. Thanks Tom for sharing yet another of your many skills with us. Your patience is fantastic - you're such a pleasure to observe. Take care 🙂
You're welcome! Yes, practice! The main thing I learned is to get a professional cutter. If you do use the cheap ones at the hardware store, always buy a new one for each job. They do not last long
Excellent work again Tom 👏👏👍
Thank you so much 👍