2012-2018 Ford Focus Thermostat Replacement How-To
ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- This video will show you how to drain the coolant replace the thermostat and housing and refill the cooling system on the 2012-2018 Ford Focus Thermostat was purchased from Amazon coolant and distilled water was purchased from Walmart.com and I have provided links below.
Motorcraft Thermostat: amzn.to/3IzdBeL
Peak Dex-cool Coolant Concentrate: goto.walmart.c...
Great Value Distilled Water: goto.walmart.c...
I did this and my car wouldn't start after. So, just to let people know, there is a connection right above the hoses, going into the housing. That connection leads to the fuel pump relay. If your car wont start after, that might be it. When I pushed it in, it only moved about an 1/8th of an inch. Looking at it, I thought it was OK, until I pushed it in. Just thought I would put this out there, just in case.
Thanks for the extra info.
Thank you ! I followed your video step by step and successfully changed thermostat in my daughters 2012 Focus. Much appreciated. Keep up the GREAT work.
Thanks. To be a successful mechanic these days you have to have small hands. I have used a very thin grease coating on hose connections or some WD40 to help them slip and seal. On those nuts I tighten until they get decidedly bottomed out and then another twist each or no more than an 8th additional turn - plastic parts don't lend a lot of confidence either side. The threads are super fine so they don't back out. Use good judgement but that O ring gasket is good.
Good morning, how do I know if I should change the temperature sensor? What I see is that when I start my vehicle in the morning the needle goes up somewhat quickly to the middle (between 30 seconds and a minute letting idle) but it never goes beyond that no matter if I drive a lot or leave the car running for several hours on a hot day... is that a symptom of a faulty temperature sensor? or that could be a symptom of the Thermostat that is failing?
If it’s in the middle that is normal operating temperature. What does it do with just the key on and engine not running?
Did you find a solution to your problem? Please reply
@@user-vq8op4mh8s He must've gotten caught up in the "middle" of something
Nice job. I have a 2012 5 speed, been a great car. I currently have a heater hose leaking at the firewall, thought it might have been the heater core, but hopefully got lucky. Ordered the hose the other day plus the tool to remove it. I'm also lucky, I work on jets, so mechanically inclined, plus I have skinny arms and long fingers!🤣 Fine work my friend!👍
I do as well. Not often, I see others who are A&Ps around these kinds of videos.
@@AMScotty Yessir! Not a real popular profession, what with all the outsourcing of our jobs to other countries over the last 4 decades. I'm close to the end myself, so not sure what the future holds for the profession in the future.
That was a great video. You spoke very clear and I hope you make more videos.
Basically if your gonna do the water pump you might as well remove the belt /tensioner and go to work on the water pump as well. I replace in pairs
Before I change the thermostat on my 2012 Ford Focus is it a must to drain the coolant first? My coolant seems to be fine, this is my first time changing the thermostat on my own!
Although draining the coolant isn’t a must but if you don’t drain it down at least a 1/4 of the way it will make a big mess once you pull the thermostat housing off. So at minimum you’ll want to drain at least some of the coolant out first.
Great video 😊
From another site, what does it mean to backfill the block to prevent an air pocket? Is that necessary?
It just means filling the block with coolant at the thermostat hole before you install it but if you do it the way I did in the video you won’t have any problems. Most of the air bubbles will work there way out into the coolant reservoir after a day of driving.
Great video I was nervous about doing this repair plus almost got the thermostat by itself
I noticed that you installed the new thermostat without gasket and sealant ? Please reply thank you
These have a rubber gasket that does not require RTV
The rubber gasket is on there at scene 13:04.
THank you for replying
Nice job! Thanks for the good explanation.
just to note that distilled water does boil.
did you have to end up taking the headlight off?
Nope
It’s. A 1.6 4 cylinder,is that called eco boost USA…?
There is a 1.6 non eco boost and a 1.6 turbo that is a eco boost but those are found in the ford fiestas.
The cost and how to change the thermostat on a 2008 Ford focus
Great vid! Thanks a lot!
Anyone done this on the 1.6 petrol ? Is it any easier or harder
Is the thermostat a wear item or 🤷
In my opinion it is, just because it goes through so many heat and cooling cycles.
Muy buen video!!! Exelente!!! Saludos!!!
Thanks for the help.
2012 you will have to loosen and hold the alternator out of the way to reach the bottom bolt. 13mm leave it hanging on top bolt and just move the bottom out of way.
Work on it and include the water pump wow the thermostat was way more difficult than the water pump
Thank you for the video.
Needs 4 bolts equal distribution will leak again bad design
Coolant leaks, engine overheats, new engine is too much, customer buys new car. Maybe a good design (for the auto industry, not for the customer)
The car wasn't leaking coolant. I think you misunderstood the video.
Wich engine is it?
It’s the 2.0
Tengo un carro igual, y me marca fallo en el Sensor MAP, pero no lo encuentro sabrás donde esta ubicado.
Great vid