Ярослав Лисецкий, Да, для меня сработало. Уже проехал около 4 тыс. Дело простое: этот резистор обманывает компютера что давление LPG достаточно высоко. Просто соединяешь ножки резистора к кабелям как показано. Сгибаешь, чтоб не мешали. У резистора нет направления, не имеет значение как его будешь соединять. Смотри видео 1:48. Там видно где подсоединить ножки резистора.
Dragan Stojkovski thank You for video.I have a Oscar(Made in Poland)LPG System and I had the same problem a faulty Pressure Sensor.I connected the resistor on PIN3 and PIN5 of the sensor and now all is OK.Thank You again.Problem solved until I get the new sensor.
I will check the pressure but i get the failure c010!? While conncting a have the failure C01? What should i do to fix the conection to the unit software ?
thank you for this video, for the final solution should i change the whole filter with the pressure sensor, or the problem is the tank and the pipes which became dirty? Any answers will be appreciated.
Zdravo draga Jas go imav istiot problem i denes staviv otpornik i problemot se izgubi Fala ti za videoto Sakam da prasam dali e ova dolgotrajno resenie i dali ima nekakva opasnost da se vozi vaka?
Zavisi kaj ti stoi elektricniot ventil za plin, ako e kaj rezervarot pozadi togas dokolku dojde do prekin na instalacija za plin nema da bide sopreno avtomatski istekuvanje na plin, a ako ventilot ti se naodja odma do rasplinjacata togas nema skoro nikakva razlika zatoa sto senzorot sto go premostuvas ke reagira dokolku ima istekuvanje na plin (pad na pritisok na plinot) samo pomegju ventilot i senzorot sto e mnogu malo rastojanie okolu 0,5 metri, vo sekoj slucaj ova bi trebalo da bide privremeno resenie ama jas ja vozam taka skoro 5 godini, razlika e samo sto koga ke ti snema plin ke treba racno da prefrlis na benzin
Zdravo edno prasanje,kaj mene od ko ke ja zapalam posle 2 min saka da prefrli ama pak vrajka na benzin isto ko kaj tebe posle 60 stepeni si raboti na plin,probav kako kaj tebe so otpornik ne svetit kolku plin ima i ne prefrla isto do 60 stepeni,dali otpornikot da go stavam na drugi zici?da ne e na prv i tret
Ako ti e lovato easyfast mora da e na tie zici otpornikot a ako imas drug plinski ured ne eksperimentiraj bez kompjuter ne pravis nisto, a moze da bide i map senzor rasipan i da ti prefrla na benzin
Hey budy ! Can you tell me on what pins to you connect it? The 5v and map or ground and pressure ? I have and aeb 025 and i want to see if it works. Thanks
Poštovanje, Dragane. Imam isti plinski uređaj u audiju a4 lovato easy, kako god, pa bih te zamolio da mi odgovoriš na nekoliko pitanja. Prije par dana mi se počelo dešavati da u toku vožnje sam prebacuje sa plina na benzin, iako je boca puna, uz pištanje kao da je prazna. Nakon što ručno prebacim na plin, on neko vrijeme radi pa ponovo prebaci na benzin i tako u krug, a interval, tj vožnja na plin do ponovnog pištanja zavisi, kako mu dođe. Da li se tebi nešto slično dešavalo? Takođe, od kako sam kupio auto, pri gašenju motora se čuju tri zvučna signala, za koja sam negdje pročitao da to označava servisni interval? Dalje, da li sijalice na prekidaču svijetle kad se da kontakt, ili samo kada se auto upali, pošto na to iskreno nisam obraćao pažnju prije, a neki kvazi majstor mi je nešto gledao oko plinske instalacije, pošto najbliži plinadžija neko vrijeme neće raditi, pa sad više ni sam ne znam da li su diode svijetlile kad se da kontakt, ili samo kada se auto upali? Unaprijed ti hvala na odgovoru, i naravno, oprosti na uznemiravanju. Srdačan pozdrav. Nebojša
Zdravo Nebojsa, ja jos uvek vozim taj auto i na njemu sam ja prvi ugradio taj plinski uredjaj i do sada imam oko 6000 radnih sati na plin i do sada nisam ni jednom cuo nikakav zvuk nakon gasenja auta tako da to ti je nesto drugo nije da je potrebno servisiranje. Sto se tice diode nema pravila nekada svete na kontakt nekada se upale tek kad upalis auto to sam jutros proverio. A kod mene kad je pocelo da prebacuje na benzin a da ima plin desilo se odjednom i nije uopste nakon toga proradilo ponovo sve dok nisam stavio taj otpornik. A imao sam slucaj da me covek isto tako pitao za isti takav problem ko tvoj pa srekjom je bio blizu mene i smo stavili taj auto na dijagnostiku za plinski uredjaj i ispalo je da mu otkazuje MAP sensor koji je na tom istom delu dge je glavni filter za plin. Sve u svemu niko nemoze da bude siguran sta je problem dok ne stavis auto na kompjuter i vidis sta se tacno dogadja u trenutku kad on prebaci na benzin. Ako se isposravi da je MAP onda tu nema improvizacije nego moras da smenis taj ceo del koji kosta od 100 eura pa nagore
@@draganexe Hvala Vam na odgovoru. Odvešću ga nadam se sledeće sedmice kod plinadžije na dijagnostiku, pa ću vidjeti šta je u pitanju. Još jednom se zahvaljujem na odgovoru i želim Vam svako dobro.
zdravo,go imam istiov problem so plinot,ne prefrla na plin i sviri a ima plin,no ponekogas znae i da prefrli,dali e samo do map senzorot ili moze da e i do filterot.
I don't know, 4k7 worked fine for me, maybe 10k will work for you. However higher value can not couse any damage, only you will get lower pressure reading.
Zdravo Dragan istiot problem e i kaj mene so pritisok,dosega imam smeneto 5 map senzori vo plomont mi velat deka kompjuterot gi gori. Ako sakas da mi kazes na koja zica go mestis otpornikot
Kaj mene ne e samo map senzor, na toj del e i filter za plin senzor za temperatura na plin i senzor zanpritisok na plin. Map senzor go meri vakumot vo granite a ne pritisokot na plinot. I ova celo vo plimont kosta 95 evra. Taka da mislam deka voopsto nemame ist plinski ured i ne bi znael kako da ti pomognam.
@@draganexe istiot e i kaj mene easyfast model so filterce i meri vacum pritisok i sl. E Sega rabotava od plimont e kao mapot raboti na 5v a vo daden moment kompjuterot se zbunuva i mu dava 12 i go gori delot kaj sto meri pritisok i nesaka da mi prefrli na plin isto kako kaj tebe sto vrednost na otpornik mu stavas fala mnogu
Delot sto meri prolitisok nema napon nego raboti samo na promena na otpornost i na toj nacin kompjuterot znae dali ima pritisok ili nema, ako nema pritisok prefrla na benzin ili ako dojde do prekin na instalacija vo slucaj na soobrakjajka avtomatski se prekinuva dovod na plin
@@draganexe Fala drugar na videoto i na tvojata nesebicnost za 1denar mi zastedi 95 Eur. Ova mi bese 5ti senzor. Da bides ziv i zdrav i so poveke videa😉
Dragan, imam i jas eden problem ne znam od kade dojde, ako znaes nesto za toa.. Prvo otkako ke ja zapalam kolata na kopceto nisto ne sveti edna minuta, pa sveti 5 sekundi se', pa pak ne sveti 1 minuta i taka celo vreme. Od denes e ova pa ne znam ni dali na plin ili na benzin vozam. Ako znaes nesto za ova da mi kazes bi bil blagodaren.
I have the pressure sensor and temperature sensor with 4 contacts lovato bosch know what is the contact pair for the pressure? so I put the resistor and fool the error
In this case pressure sensor is used only for switch back to petrol when you are running out of gas, and it have nothing in common with auto calibration. So you still can do all adjustment like before.
radi li na stag uredjajima isto ovako?Prvo paljenje prebaci tek posle 20km voznje.U racunaru javlja gas pressure sensor error too low ali mi je cudno sto kasnije u toku voznje kada se sve ugreje radi bez problema?
Pozz imam instalirano lovato exr na bmw 316 1.8 motor valvetronic motor se bese dobro odess super samo vo ler seckase go odnesov kaj tie sto mi go montira p go sedia i sea mi izgleda deka trosi i benzin pa mislam deka go napraile na ler gas da raboti na benzin kako mozham da proveram dali raboti na ler gas na benzin ili plin ?
Moze da se napravi na pogolemi obrtai da raboti na benzin ili da dofava benzin a na ler gas na benzin mislam deka nema takva opcija, koga ke se povrze na kompjuter moze da se vidi na sto raboti
Zdravo prijatel go imam istiot problem so plinot ne prefrla na plin i sviri a ima plin ,no poneko gas znae i da prefrli dali e mozno do map senzorot go smeniv senzorot kaj raspinjaca za temperatura nishto isto e pak
Bez kompjuterska dijagnostika nikoj ne moze da kaze sto e problemot, pa nekogas ni na kompjuter ne pokazuva nisto a kolata pravi problem. Moze da bide bukvalno bilo sto. Eden prijatel ima takov problem i nikoj ne mu go resi nemaat poim sto bi mozelo da bide i site mu nudat da mu montiraat nov plinski ured
Please tell me from where did u find the interface cable for lovato .?? Im searching for it from so long and none of the chinese cable worked... please please help me..
ja ovako isti problem imam Pressure Sensor sam mu zamjenijo polovni pokazujem mi isti problem ovaj sto sam zamjenijo neznam dali je ispravan pollovan je
Lovato Sequential Kit. Showing Red light and sometime switches to petrol... I have Nissan Teana 230 JM (Six Cylinder V6). Now i am facing an issue related to the CNG (Lovato Sequential). It was working fine with Petrol and CNG since four years. But now it shows red light on the indicator even if the gas is full. Sometimes shows 3 green light some times 2, basically it fluctuates. And the main problem is, it shifts to Petrol after showing red light in some time even if the gas is there. Then I have to restart the car and it shifts to CNG and works fine but still shows the red light. However the pressure gauge (similar to clock) is showing proper reading. I have shown this problem to a Lovato mechanic he replaced CNG Gauge Meter it worked fine for some minutes and then the same problem again. Now he is saying it might be some wiring issue but he is not confident. He did all the settings through the computer but still no luck. Any suggestions ?
Pocituvan imam problem so MAP senzorot isto kako sto e vo vaseto video. Jas na moeto vozilo imam Lovato MAP senzor od modelot koj sto ima cetiri priklucoci za creva. dali istoto mozam da go napravam i na moeto vozilo i dali posle toa treba da ja odnesam kolata na steluvanje na mapata. Pozdrav
Kaj mene problemot bese so senzorot za pritisok na plin, istiot moze da se premosti zatoa sto ne e bitno kolku pritisok pokazuva bitno e da ne ti go isklucuva dovodot na plin. A dodeka MAP sensorot dava razlicni vrednosti vo odnos na vakumot sto go ima vo granite, i istiot ima vlijanie na potrosuvackata. Taka da ako mu stavis fiksna vrednost mozebi kolata ke raboti ama nema da e kako sto treba, ili mnogu ke trosi ili nema da odi.
I need solution for my Lovato lpg smart exr sequential kit. Vehicle is showing warning light on particular interval. Error code is P0171 (system too lean). After re-tuning also same error. Kindly help
thank you for help. i checked on aliexpress about pinouts and sensor is for both LPG and CNG is same there and Pinouts are as 1=12V supply, 2=Temprature, 3=Pressure, 4=MAP, 5=Ground. can you please tell me Pin1 wire color? i ll try using 4.7K tomorrow and let you know. can i clean the sensor with some carb cleaner?
Sir I have a car Tata zest turbo petrol ingine Lovato cng kit installed pls help me which value resistance will perfect match(1.2k and 6.8k 1/4 w is not work properly change petrol to cng easily but car running in jucust 10 meters it's back again petrol beep measer led sign of cng point just blinking and beep sound) help me shop dealer says is map sensor is faulty but I have no money Help me I am from India
Hello, may I have your email address? I have tried the same has you but the car still has some GPL pressure failure, after driving for 10 min. Is that normal?
my cng car giving false Alarmof empty CNG gas even if it is full of tank.. please help how to solve this problem. someone told me that this is because of pressure MAP sensor of 5 pin installed. how can i fix this myself. i added 6.8K resistor today but it is beeping again
Bez kompjutera nemoz znat jel u pitanju sensor pritiska, mozda je kod tebe drugi problem da kazemo senzor temperature plina. A to spajanje zicom mislim da nije pametno, jer ako prespojis nesto drugo mogo bi da prouzrukujes jos veci problem
Dragan Stojkovski thank you very much. Problem is solved. My mistake one of the legs of the map was bendet. Now working fine but stil when i drive fast it switch to gasoline for few seconds and then back to lpg. What can be the problem? Also morning time the engine stops when it change to lpg. Thank you for your help
In my case 4k7 was just right, you can try first with 5k if doesn't work try with 3k3 for example. But without computer diagnostic it's very difficult to do right ajdustment.
(just to make it clearer - the resistor is 0.25w 6.8 kOhm)
Thank you very much for this video, Dragan! I tried it myself and my problem is solved.
Александър Александров That's right 6.8 kOhm or 6k8 it's the same
Александър Александров оно реально работает? или на время? что по подробней делать?
Ярослав Лисецкий, Да, для меня сработало. Уже проехал около 4 тыс. Дело простое: этот резистор обманывает компютера что давление LPG достаточно высоко.
Просто соединяешь ножки резистора к кабелям как показано. Сгибаешь, чтоб не мешали. У резистора нет направления, не имеет значение как его будешь соединять.
Смотри видео 1:48. Там видно где подсоединить ножки резистора.
A dont no
Spune-mi și mie te rog care pini trebuie legați? Pinul 1 ( roșu) cu pinul 3?? Sau pinul 1( negru) cu pinul 3??
działa jak złoto! thx ! tak przy okazji ja musiałem całkowicie wypiąć wtyczkę z czujnika po zmostkowaniu żeby zadziałało
Dragan Stojkovski thank You for video.I have a Oscar(Made in Poland)LPG System and I had the same problem a faulty Pressure Sensor.I connected the resistor on PIN3 and PIN5 of the sensor and now all is OK.Thank You again.Problem solved until I get the new sensor.
marin skugor moglbys mi powiedzieć w jakie piny wpiąć ten drucik ?
@@kacperstefanski1548 english please:)
I will check the pressure but i get the failure c010!? While conncting a have the failure C01? What should i do to fix the conection to the unit software ?
thank you for this video, for the final solution should i change the whole filter with the pressure sensor, or the problem is the tank and the pipes which became dirty? Any answers will be appreciated.
I think that if you replace filter with pressure sensor it will solve your problem.
Zdravo draga
Jas go imav istiot problem i denes staviv otpornik i problemot se izgubi
Fala ti za videoto
Sakam da prasam dali e ova dolgotrajno resenie i dali ima nekakva opasnost da se vozi vaka?
Zavisi kaj ti stoi elektricniot ventil za plin, ako e kaj rezervarot pozadi togas dokolku dojde do prekin na instalacija za plin nema da bide sopreno avtomatski istekuvanje na plin, a ako ventilot ti se naodja odma do rasplinjacata togas nema skoro nikakva razlika zatoa sto senzorot sto go premostuvas ke reagira dokolku ima istekuvanje na plin (pad na pritisok na plinot) samo pomegju ventilot i senzorot sto e mnogu malo rastojanie okolu 0,5 metri, vo sekoj slucaj ova bi trebalo da bide privremeno resenie ama jas ja vozam taka skoro 5 godini, razlika e samo sto koga ke ti snema plin ke treba racno da prefrlis na benzin
Hi, Can you tell me what software did you use to check the gas pressure?
Lovato Easy Fast
Hello! Do you have any schematics how to change LPG filter for lovato system like yours? Thank you
I have Stag 5 wire map lpg sensor in my car.can I try the same on Stag or its just for lovato.thankx
Zdravo edno prasanje,kaj mene od ko ke ja zapalam posle 2 min saka da prefrli ama pak vrajka na benzin isto ko kaj tebe posle 60 stepeni si raboti na plin,probav kako kaj tebe so otpornik ne svetit kolku plin ima i ne prefrla isto do 60 stepeni,dali otpornikot da go stavam na drugi zici?da ne e na prv i tret
Ako ti e lovato easyfast mora da e na tie zici otpornikot a ako imas drug plinski ured ne eksperimentiraj bez kompjuter ne pravis nisto, a moze da bide i map senzor rasipan i da ti prefrla na benzin
@@draganexe falati zavrsiv rabota,otpornikot go staviv na 1va i 2 ra zica,2ra ta e za temperatura i si prefrla odma
Hey budy ! Can you tell me on what pins to you connect it? The 5v and map or ground and pressure ? I have and aeb 025 and i want to see if it works. Thanks
Did you find out how to do it for AEB025?
Hi, between which pins numbers resistors are connected?
the middle one with the right one, as you see it from the secure connector
@@αγγελοςκοντεκας μήπως έχεις ιδέα πως να κάνω το αντίστοιχο στον ΑΕΒ025 αισθητήρα σε zavolli ?
Poštovanje, Dragane.
Imam isti plinski uređaj u audiju a4 lovato easy, kako god, pa bih te zamolio da mi odgovoriš na nekoliko pitanja.
Prije par dana mi se počelo dešavati da u toku vožnje sam prebacuje sa plina na benzin, iako je boca puna, uz pištanje kao da je prazna.
Nakon što ručno prebacim na plin, on neko vrijeme radi pa ponovo prebaci na benzin i tako u krug, a interval, tj vožnja na plin do ponovnog pištanja zavisi, kako mu dođe.
Da li se tebi nešto slično dešavalo?
Takođe, od kako sam kupio auto, pri gašenju motora se čuju tri zvučna signala, za koja sam negdje pročitao da to označava servisni interval?
Dalje, da li sijalice na prekidaču svijetle kad se da kontakt, ili samo kada se auto upali, pošto na to iskreno nisam obraćao pažnju prije, a neki kvazi majstor mi je nešto gledao oko plinske instalacije, pošto najbliži plinadžija neko vrijeme neće raditi, pa sad više ni sam ne znam da li su diode svijetlile kad se da kontakt, ili samo kada se auto upali?
Unaprijed ti hvala na odgovoru, i naravno, oprosti na uznemiravanju.
Srdačan pozdrav.
Nebojša
Zdravo Nebojsa, ja jos uvek vozim taj auto i na njemu sam ja prvi ugradio taj plinski uredjaj i do sada imam oko 6000 radnih sati na plin i do sada nisam ni jednom cuo nikakav zvuk nakon gasenja auta tako da to ti je nesto drugo nije da je potrebno servisiranje. Sto se tice diode nema pravila nekada svete na kontakt nekada se upale tek kad upalis auto to sam jutros proverio. A kod mene kad je pocelo da prebacuje na benzin a da ima plin desilo se odjednom i nije uopste nakon toga proradilo ponovo sve dok nisam stavio taj otpornik. A imao sam slucaj da me covek isto tako pitao za isti takav problem ko tvoj pa srekjom je bio blizu mene i smo stavili taj auto na dijagnostiku za plinski uredjaj i ispalo je da mu otkazuje MAP sensor koji je na tom istom delu dge je glavni filter za plin. Sve u svemu niko nemoze da bude siguran sta je problem dok ne stavis auto na kompjuter i vidis sta se tacno dogadja u trenutku kad on prebaci na benzin. Ako se isposravi da je MAP onda tu nema improvizacije nego moras da smenis taj ceo del koji kosta od 100 eura pa nagore
@@draganexe Hvala Vam na odgovoru.
Odvešću ga nadam se sledeće sedmice kod plinadžije na dijagnostiku, pa ću vidjeti šta je u pitanju.
Još jednom se zahvaljujem na odgovoru i želim Vam svako dobro.
Super efekt, 150-250 zł w kieszeni. Polecam
Siemka czytam że polak napiszesz jakiego rezystorka użyłeś i w które piny wsadziłeś
@@Adinnna Naprawiłeś? Bo jutro jadę kupić rezystor tylko nie jestem pewny o jakiej rezystancji :D
@@indus7riouz281
Cześć, jaki to rezystor? Zadzialalo?
Jakiego rezystora uzyliscie?
@@adammakow5862 Działa do dzisiaj, jutro sprawdzę jaki rezystor mam, bo już nie pamiętam.
Na komputerze pokazuje ciśnienie 3 bary :D
to witch pins you pout the resistor?
zdravo,go imam istiov problem so plinot,ne prefrla na plin i sviri a ima plin,no ponekogas znae i da prefrli,dali e samo do map senzorot ili moze da e i do filterot.
Go imam istiot problem brat jas sea dali go reshi problemot?
Dragan Stojkovski - Thank you ! 0.25w 6.8 kOhm. All earned. Hello from Russia. ))
Ja mam 3 piny, do ktorego ma podlaczyc. Prosze o odpowiedz
hello, thanks for this video!
will 10K resistor work for me?
I don't know, 4k7 worked fine for me, maybe 10k will work for you. However higher value can not couse any damage, only you will get lower pressure reading.
thanks for reply, i'll try it soon and update here!
Zdravo Dragan istiot problem e i kaj mene so pritisok,dosega imam smeneto 5 map senzori vo plomont mi velat deka kompjuterot gi gori. Ako sakas da mi kazes na koja zica go mestis otpornikot
Kaj mene ne e samo map senzor, na toj del e i filter za plin senzor za temperatura na plin i senzor zanpritisok na plin. Map senzor go meri vakumot vo granite a ne pritisokot na plinot. I ova celo vo plimont kosta 95 evra. Taka da mislam deka voopsto nemame ist plinski ured i ne bi znael kako da ti pomognam.
@@draganexe istiot e i kaj mene easyfast model so filterce i meri vacum pritisok i sl. E Sega rabotava od plimont e kao mapot raboti na 5v a vo daden moment kompjuterot se zbunuva i mu dava 12 i go gori delot kaj sto meri pritisok i nesaka da mi prefrli na plin isto kako kaj tebe sto vrednost na otpornik mu stavas fala mnogu
4,7 kilo omi
Delot sto meri prolitisok nema napon nego raboti samo na promena na otpornost i na toj nacin kompjuterot znae dali ima pritisok ili nema, ako nema pritisok prefrla na benzin ili ako dojde do prekin na instalacija vo slucaj na soobrakjajka avtomatski se prekinuva dovod na plin
@@draganexe Fala drugar na videoto i na tvojata nesebicnost za 1denar mi zastedi 95 Eur. Ova mi bese 5ti senzor. Da bides ziv i zdrav i so poveke videa😉
Dragan, imam i jas eden problem ne znam od kade dojde, ako znaes nesto za toa..
Prvo otkako ke ja zapalam kolata na kopceto nisto ne sveti edna minuta, pa sveti 5 sekundi se', pa pak ne sveti 1 minuta i taka celo vreme. Od denes e ova pa ne znam ni dali na plin ili na benzin vozam. Ako znaes nesto za ova da mi kazes bi bil blagodaren.
Imav takov slucaj uste prviot den koga go namestiv plinot, mi go smenija kompjuterot i sega e ok.
Dragan Stojkovski brat, zicka skinata od edna stega sto mi ja stavi efen "majstor" prethodno. Ja zalemivme, se e ok. Fala na brziot odgovor.
I have the pressure sensor and temperature sensor with 4 contacts lovato bosch know what is the contact pair for the pressure? so I put the resistor and fool the error
so after you put the resistor, is it still can to do auto calibration?
In this case pressure sensor is used only for switch back to petrol when you are running out of gas, and it have nothing in common with auto calibration. So you still can do all adjustment like before.
if i can't switch to the gas with the same condition shown by the switch like yours( the buzzer, the LED), can this method use?
yes
ibrahim umar alisjahbana Yes you can try
radi li na stag uredjajima isto ovako?Prvo paljenje prebaci tek posle 20km voznje.U racunaru javlja gas pressure sensor error too low ali mi je cudno sto kasnije u toku voznje kada se sve ugreje radi bez problema?
Nemam iskustva sa stag uredjajima, ali cim javlja gresku kod senzora za pritisak onda je to to, otkazuje polako
@@draganexe Zar map senzor moze tako da se ponasa,on ili radi ili ne radi?
Map senzor ne meri pritisak nego vakum, a gas pressure sensor meri pritisak plina. Znaci kod tebe map sensor nije problem
it should work also with a 1/4W 1K2 resistor, right?
I think so, but you will have maximum pressure reading
Pozz imam instalirano lovato exr na bmw 316 1.8 motor valvetronic motor se bese dobro odess super samo vo ler seckase go odnesov kaj tie sto mi go montira p go sedia i sea mi izgleda deka trosi i benzin pa mislam deka go napraile na ler gas da raboti na benzin kako mozham da proveram dali raboti na ler gas na benzin ili plin ?
Moze da se napravi na pogolemi obrtai da raboti na benzin ili da dofava benzin a na ler gas na benzin mislam deka nema takva opcija, koga ke se povrze na kompjuter moze da se vidi na sto raboti
Zdravo prijatel go imam istiot problem so plinot ne prefrla na plin i sviri a ima plin ,no poneko gas znae i da prefrli dali e mozno do map senzorot go smeniv senzorot kaj raspinjaca za temperatura nishto isto e pak
Bez kompjuterska dijagnostika nikoj ne moze da kaze sto e problemot, pa nekogas ni na kompjuter ne pokazuva nisto a kolata pravi problem. Moze da bide bukvalno bilo sto. Eden prijatel ima takov problem i nikoj ne mu go resi nemaat poim sto bi mozelo da bide i site mu nudat da mu montiraat nov plinski ured
It works for me, but what happens then gas tank will be empty, it switch to petrol or engine stops working?
You will know when your lpg tank is empty, then you have to switch to petrol manualy
I got the 6.8kohm but only .5w it should be ok i will test and let you know. The .5w is just for heat range.
Just tested it driven 20km works great I used 5w 6.8 kohm. Thanks for great video.
Please tell me from where did u find the interface cable for lovato .?? Im searching for it from so long and none of the chinese cable worked... please please help me..
It was long time ago, I dont know exactly, I only remember that was Turkish online store.
ja ovako isti problem imam Pressure Sensor sam mu zamjenijo polovni pokazujem mi isti problem ovaj sto sam zamjenijo neznam dali je ispravan pollovan je
Can you please tell color codes of wires?
Is this really 6k8 resistor? Any other specifications? I need to try this, but don't want to do it wrong and fry something... Thank you!
Yes it is, 6k8 1/4 w
Dragan Stojkovski thank you very much! Hvala!
Lovato Sequential Kit. Showing Red light and sometime switches to petrol...
I have Nissan Teana 230 JM (Six Cylinder V6). Now i am facing an issue related to the CNG
(Lovato Sequential). It was working fine with Petrol and CNG since four years. But now it shows red light on the indicator even if the gas is full. Sometimes shows 3 green light some times 2, basically it fluctuates. And the main problem is, it shifts to Petrol after showing red light in some time even if the gas is there. Then I have to restart the car and it shifts to CNG and works fine but still shows the red light. However the pressure gauge (similar to clock) is showing proper reading.
I have shown this problem to a Lovato mechanic he replaced CNG Gauge Meter it worked fine for some minutes and then the same problem again. Now he is saying it might be some wiring issue but he is not confident. He did all the settings through the computer but still no luck.
Any suggestions ?
I am having the same problem. I t switching on its own.
Pocituvan imam problem so MAP senzorot isto kako sto e vo vaseto video. Jas na moeto vozilo imam Lovato MAP senzor od modelot koj sto ima cetiri priklucoci za creva. dali istoto mozam da go napravam i na moeto vozilo i dali posle toa treba da ja odnesam kolata na steluvanje na mapata. Pozdrav
Kaj mene problemot bese so senzorot za pritisok na plin, istiot moze da se premosti zatoa sto ne e bitno kolku pritisok pokazuva bitno e da ne ti go isklucuva dovodot na plin. A dodeka MAP sensorot dava razlicni vrednosti vo odnos na vakumot sto go ima vo granite, i istiot ima vlijanie na potrosuvackata. Taka da ako mu stavis fiksna vrednost mozebi kolata ke raboti ama nema da e kako sto treba, ili mnogu ke trosi ili nema da odi.
Najverovatno ke mora nov MAP senzor. sepak Fala ti.
I need solution for my Lovato lpg smart exr sequential kit. Vehicle is showing warning light on particular interval. Error code is P0171 (system too lean). After re-tuning also same error. Kindly help
I had the same problem one of pipe from lpg injector was loose and it was sucking air and engine light was coming on.
@@MrNaeemkhan000 use Nano lube additive & compression booster. The engine light will vanish.
Słabo widać, czy można z dokładnością na. Kostkę ?
pin number 1 and 3
@@draganexe niestety u mnie to nie działa. Prawdopodobnie całkowicie padł map sensor
what is PIN 1? is it power supply or ground? pin3 seems pressure but what is pin1?
There is no power on any wire, only ground and signal wire
Mine is LPG not CNG
I don't know are they the same
And you have to know that MAP is not measuring the pressure of gas
thank you for help. i checked on aliexpress about pinouts and sensor is for both LPG and CNG is same there and Pinouts are as 1=12V supply, 2=Temprature, 3=Pressure, 4=MAP, 5=Ground. can you please tell me Pin1 wire color? i ll try using 4.7K tomorrow and let you know. can i clean the sensor with some carb cleaner?
hot to download the software on my pc??
Sir I have a car
Tata zest turbo petrol ingine Lovato cng kit installed pls help me which value resistance will perfect match(1.2k and 6.8k 1/4 w is not work properly change petrol to cng easily but car running in jucust 10 meters it's back again petrol beep measer led sign of cng point just blinking and beep sound) help me shop dealer says is map sensor is faulty but I have no money
Help me I am from India
Without computer diagnostic you can't be sure which part is faulty, map or gas prassure sensor. In my case 4k7 ohm works perfectly.
@@draganexe ok sir I will check after then reply
Thanks for reply sir
Kako da ve iskontaktiram,email ili slicno
Hello, may I have your email address?
I have tried the same has you but the car still has some GPL pressure failure, after driving for 10 min.
Is that normal?
my cng car giving false Alarmof empty CNG gas even if it is full of tank.. please help how to solve this problem. someone told me that this is because of pressure MAP sensor of 5 pin installed. how can i fix this myself. i added 6.8K resistor today but it is beeping again
Try with lower value, 4k7
9824930589
dali moze obicna zica od bakra spoit
Bez kompjutera nemoz znat jel u pitanju sensor pritiska, mozda je kod tebe drugi problem da kazemo senzor temperature plina. A to spajanje zicom mislim da nije pametno, jer ako prespojis nesto drugo mogo bi da prouzrukujes jos veci problem
@@draganexe Hvala ti na brzom odgovoru pogledacu senzor teparature imam obd ali ne pokazuje mi feler problem
@@draganexe Hvala ti na brzom odgovoru pogledacu senzor teparature
@@draganexe evo koliko me je kostalo 250 eura :) kod njemackog mehanicara reko mi je da je u tank rezervar problem ventil
can you do this with the car off?
Yes, you can
Fala ti care!!!
Odakle ste skunuli tu kablu
Druze koje zice si prespojio? Ja imam stag ps 01
Ne bi znao da ti kazem, ja sam kod mene probao sve kombinacije dok nisam nasao pravu. Ali moras da imas dijagnostiku za to
Druze i ja imam problem u pitanju e ac stag 5 pin senzor, gde da povezem otpornik izmedzu koi pinova
Moras da imas dijagnostiku da bi znao gde da prespojis
Dragan Stojkovski: Maybe you know where the pin is the sensor map and how to deceive it?
I am afraid that the map sensor cannot be easily deceived.
I ask because I have a valvetronic engine and the map sensor error disables the installation. Map sensor should not be considered in this engine.
Pin 1 and 3 is pressure sensor
Pin 1 and 4 is MAP sensor
I tested it. :)
@@adamwesoowski101 możesz napisać czy to działa?u mnie kostka ma 4 piny .Podpinam 1 oraz 3 rezystor i niestety nie działa ,dalej to samo
@@bamber851 dziala ale skoro masz inna kostkę to mozesz miec inna instalacje. Testowane juz wielokrotnie przy easy smart
I make it as you show in the video but after one minute it switched again to gasoline
+ivan ivanov You can try to put resistor with higher value, for example 5k6 instead of 4k7
Dragan Stojkovski thank you very much. Problem is solved. My mistake one of the legs of the map was bendet. Now working fine but stil when i drive fast it switch to gasoline for few seconds and then back to lpg. What can be the problem? Also morning time the engine stops when it change to lpg. Thank you for your help
Hi ivan i have the same problem as yours when driving fast lpg go to petrol do you find any solution ?
Ребята, напишите нормально что туда запихается и на сколько!!! по русски пожалуйста!
Work just few minutes
Try with another resistor
Pls give me a full detail of all type resistance with value pls
In my case 4k7 was just right, you can try first with 5k if doesn't work try with 3k3 for example. But without computer diagnostic it's very difficult to do right ajdustment.