722.9 4Matic Transmission Teardown

แชร์
ฝัง

ความคิดเห็น • 94

  • @oldschool9746
    @oldschool9746 2 ปีที่แล้ว +3

    Thank you Gary, hope you have a great week!

  • @jimmyroos1677
    @jimmyroos1677 2 ปีที่แล้ว +1

    Gary, the B1 clutch basket really sits !!! I use a solid plastic hammer and HAMMER it from the bell -housing side, no marks or dents ...

  • @TheKarabala
    @TheKarabala 2 ปีที่แล้ว +1

    Nice to see you Gary. Take care

  • @igotaction
    @igotaction 2 ปีที่แล้ว +6

    Keep the ZFs and 722s coming Gary!!!!

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      Thanks Joel Will do

    • @AbdMehidden
      @AbdMehidden ปีที่แล้ว +1

      Good morning Fran hwry l need work WD you lm mknk

  • @SrColon309
    @SrColon309 ปีที่แล้ว

    Thanks for sharing your knowledge and experience.

  • @silver-blz3112
    @silver-blz3112 11 หลายเดือนก่อน

    Do you have a part 2 of this, where you show the problems and put everything together again?
    Keep going!

  • @sabastianrobar1269
    @sabastianrobar1269 8 วันที่ผ่านมา

    I’m rebuilding my transfer case on my 2015 c300 4matic, 722.9. is there a part number for the hex bolt removed at 16:00 ??? Have everything mostly back together but am having trouble referencing if the bolt I purchased is the same one

  • @jimmyroos1677
    @jimmyroos1677 2 ปีที่แล้ว +1

    I change the allu bolts with the 722-6 transmission bell housing steel bolts, had a couple of oil leaks, after this no more problems.

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      722.6 You change the bolts?

    • @jimmyroos1677
      @jimmyroos1677 2 ปีที่แล้ว +1

      No ,I exchange the aluminum bolts for the steel one's out of the 722-6 box ,u can tighten them properly without them breaking off.

  • @chrispy104k
    @chrispy104k 4 หลายเดือนก่อน

    Hey Garry, did you ever record a videos of the rebuild of a 722.9?..... or does the viewer assume that the reassembly is just the reversal of the teardown process?

    • @GaryFerraro
      @GaryFerraro  4 หลายเดือนก่อน

      I do not have a rebuild on the 722.9 as of right now

  • @AbdMehidden
    @AbdMehidden ปีที่แล้ว +2

    ❤❤❤❤❤

    • @AbdMehidden
      @AbdMehidden ปีที่แล้ว +1

      Wer you my frand NYS to match

    • @AbdMehidden
      @AbdMehidden ปีที่แล้ว

      Im making

  • @christopheredwards3
    @christopheredwards3 2 ปีที่แล้ว

    Aren't the aluminum bolts replaced.i thought they were one time use.

  • @richbenzer5926
    @richbenzer5926 2 ปีที่แล้ว

    Great vid! Thanks for posting these. Can you post a parts list for the rebuild kit please? I have a 2006 ML500 I bought cheap with a trans that works occasionally, slips, doesn't want to engage, I figure it needs a similar rebuild. I redid a conductor plate/TCM on an 04E500 ($900 car, very nice otherwise) that solved that problem but have not torn into the guts on these boxes. Your vids on the 722.9 are awesome!

    • @LynxStarAuto
      @LynxStarAuto 2 ปีที่แล้ว

      The inductor plate on a 722.9 is a totally different animal than the 722.6. On the 9 speed the transmission computer is part of the plate. It's a 4 figure part, and locked away behind TRP. TRP is what Mercedes calls Theft Relevant Parts. You need to have a commercial garage keepers insurance policy, as well as be bonded to purchase the part. It will not otherwise be sold over the counter.
      Finally, the part must be new as a used one cannot be reprogrammed to another vehicle. At least not through official channels. There are "hackers" out there that use black market tools to clone a used module but good luck. They are harder to find than hens' teeth, and in my experience it will work, but the OBD system will have glitches later on.

    • @richbenzer5926
      @richbenzer5926 2 ปีที่แล้ว

      @@LynxStarAuto thanks for the reply. I have actually installed a reprogrammed used CP/TCM in a 722.9 and it works fine so I’m familiar with that process. This other vehicle has lost fluid pressure but the CP/TCM controls work ok, just doesn’t have enough pressure to do transmission stuff. Rebuild time! Your vids are awesome, I really enjoy and appreciate your work.

  • @Innova_1979
    @Innova_1979 2 ปีที่แล้ว

    In this scenario; is the point that the transmission shop says I need a new transmission rather than the individual component repairs?
    Seems like a lot has went south on this 722.9. Being the owner of a non-4-matic 722.9 that occasionally has a jerky shift from 1-2, this has me interested. Please keep the Benz 722.9's coming! Lots to lean here.

  • @alexandercleve5316
    @alexandercleve5316 ปีที่แล้ว

    part number on the outgoing shaft for the front differential?

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว

      You mean what the front drive shaft splines into

    • @alexandercleve5316
      @alexandercleve5316 ปีที่แล้ว

      @@GaryFerraro yes, the one you are replacing in another video, number 19 in Mercedes service documents

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว

      Not sure there is a part number, not sold separately, i always have to go good used on that. I was talking to another shop once that sourced out a new one that came from poland@@alexandercleve5316

  • @jimmyroos1677
    @jimmyroos1677 2 ปีที่แล้ว

    Hallo Gary ,if u could maybe help, I've got a Mitsubishi V4A51 Auto box, it won't shift into 4rth gear ,ie no response to 4rth gear no matter in what position the overdrive button is in .the o/d light does function correctly, the Auto lec said no problem, it's in the box .I fitted a complete different valvebody inc solenoids, no difference, new speed sensors no difference, I've stripped the complete box ,can't see anything wrong. No fault codes, don't know where to from here !!!.

  • @yolvimazariegos2820
    @yolvimazariegos2820 14 วันที่ผ่านมา

    How do you install the shaft ? The shaft is out he case? The 4 weel shaft ,

    • @GaryFerraro
      @GaryFerraro  14 วันที่ผ่านมา

      My installers know how to do that, I do not

  • @НиколайГринько-ю3ч
    @НиколайГринько-ю3ч ปีที่แล้ว

    Hi Gary from Belarus. It's a great video again. But I have some problem with ML 350. He had a torque convertor vibration when speed was from 75 to 90 km/h. We rebuilded torque converter, checked all clutch clearences and cleaned VB, new oil and new filter. And after this we have rpm rising when 1-2 shifting and sometimes hard 1-2 shifting. I did VB vacuum test and found that supply pressure regulator valves had 14 Hg instead 18 Hg. Is this a key of my problem? What do you think?

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว +1

      to me 14 inches of vacuum is low

    • @НиколайГринько-ю3ч
      @НиколайГринько-ю3ч ปีที่แล้ว

      @@GaryFerraro thank you and what I can to do to rise vacuum?

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว

      bore may be worn out, I do valvebodies in everyone i rebuild now. I bore is worn out, oversized valve will need to be installed, you can se what Sonnax has for this unit.@@НиколайГринько-ю3ч

  • @stics412
    @stics412 2 ปีที่แล้ว

    Shop says torque converter lock issue or transmission on this same transmission. No codes reported. Would you recommend changing the torque converter. The issue is vibration at stop. All mounts replaced. Thanks

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      does it seem like it wants to stall when coming to a stop? Driving no shudder?

    • @stics412
      @stics412 2 ปีที่แล้ว

      @@GaryFerraro It stalled once maybe twice had to put in park! Rides smooth but sometimes it jerks. No noise while driving only vibration on brake

  • @enriquecastro2352
    @enriquecastro2352 10 หลายเดือนก่อน

    very good video. I have a question, I have been working with a 722.9 gearbox for more than 1 month, I changed all the clutch discs with an international pressure master kit, everything new, the orings and rings are also new. I have a leak in the K2, the K2 clutch engages but loses pressure. Perform the test with air using the test holes indicated in the manual. Has it happened to anyone?

    • @GaryFerraro
      @GaryFerraro  10 หลายเดือนก่อน

      If you check just the drum is it ok

    • @enriquecastro2352
      @enriquecastro2352 10 หลายเดือนก่อน

      @@GaryFerraro Yes, just check the drum by sending air through the shaft and the drum does not leak. but when I carry out the test through the hole in the box, the drum applies but it is not applied, the air comes out

    • @GaryFerraro
      @GaryFerraro  10 หลายเดือนก่อน

      very hard to get a solid air check on the drum, i have an air check tool that i use. Did you air check through the pump support before loading everything into the case@@enriquecastro2352

    • @enriquecastro2352
      @enriquecastro2352 10 หลายเดือนก่อน

      @@GaryFerraro The K2 loses power through the axis that goes to the converter. Is that normal?

    • @GaryFerraro
      @GaryFerraro  10 หลายเดือนก่อน

      it may yes@@enriquecastro2352

  • @basketballjones6782
    @basketballjones6782 11 หลายเดือนก่อน

    @ 2:05
    So, basically, you had codes indicating the typical conductor plate issues these transmissions are well-known for, and you decided it would be a good idea to just rebuild the whole transmission.
    Mmmmkay.
    Thanks for reaffirming for me why I will never take any vehicle I own to a repair shop but instead do all my own work. Even if I have to buy a bazillion special tools and electronic gadgets to work on a modern car, I'll still end up paying far less and get much better results.

    • @GaryFerraro
      @GaryFerraro  11 หลายเดือนก่อน

      The title of the video is slips in 4th, conductor plate will not cause this, internal problem

  • @illyapalamarchuk3525
    @illyapalamarchuk3525 ปีที่แล้ว

    Hey so I was doing some donuts on dry asphalt and I heard a loud bang and now no drive or reverse gear what could’ve broken?

  • @pedromfonseca1
    @pedromfonseca1 2 ปีที่แล้ว

    Nice video! Just a quick question. I have a Mercedes GL also with a 722.9 and when doing a transmission service I found copper/bronze filings in the oil pan. Any idea were the filings would be coming from? Thank you in advance

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      I'm thinking converter, was there a lot in the pan?

    • @pedromfonseca1
      @pedromfonseca1 2 ปีที่แล้ว

      Yes there was quite a bit. Is this something I should worry about? I did have faults for torque converter lock up. No fault now.

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      @@pedromfonseca1 Converter maybe on the way out if pan had a lot of Debris

    • @pedromfonseca1
      @pedromfonseca1 2 ปีที่แล้ว

      Gary thank you again for the quick reply. I sent the torque converter out to inspect and rebuild. They said that there was nothing wrong with it. Looking at your video several times and I just don't see any copper or brass. Could it be inside the transmission oil pump or oil cooler?

    • @pedromfonseca1
      @pedromfonseca1 2 ปีที่แล้ว

      Looks like it could be the washers on the planetary gear set.

  • @sukiiish
    @sukiiish ปีที่แล้ว

    What if transmission have plus 1 liter oil. Will be to much presure ? Or will be damaged transmission ?

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว

      Shouldn't cause to much damage, may shift erratic if solenoids can't exhaust fast enough or may come out of the vent when hot

  • @infocentrousmajac
    @infocentrousmajac ปีที่แล้ว +1

    you need to invest on a better camera and better illumination. Transmission repair requires not only knowledge but bery fine image detail to show damaged parts. I have learned a lot from your videos but the image quality can be improved.
    Keep up the good work!

  • @igotaction
    @igotaction 2 ปีที่แล้ว

    Doesn't that take the blue 134FE fluid??? Is it that burnt I know you said it looked like it had been worked on.

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      Thats what they say, 7G Tronic Plus. Premium synthetic is good

  • @AbdMehidden
    @AbdMehidden ปีที่แล้ว +1

    very good my frand wr you form

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว +1

      I live in New York

    • @AbdMehidden
      @AbdMehidden ปีที่แล้ว

      @@GaryFerraro lm from pLstyn

  • @RuCuber
    @RuCuber 2 ปีที่แล้ว

    Can you please tell us how much it costed the customer to get this kind of repair done?

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      overhaul the unit or a transfer case repair?

    • @RuCuber
      @RuCuber 2 ปีที่แล้ว

      @@GaryFerraro I mean the price of the master kit and the valve body + cost of work done for the transmission

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      @@RuCuber around 5 to 5.5K

  • @vardansahakyan9805
    @vardansahakyan9805 4 หลายเดือนก่อน

    Was looking for an ml 500 m113 engine with this transmission, 2006. Actually it's a good old car with good engine but the transmission seems a big deal breaker.
    Too unreliable both mechanically and electrically.
    Don't know if I can trust this one ?

    • @GaryFerraro
      @GaryFerraro  4 หลายเดือนก่อน

      i do a lot of these units

  • @torrencedupree5525
    @torrencedupree5525 ปีที่แล้ว

    Can I put a 09 e550 4matic transmission in a 09 s550 4matic

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว +1

      cannot say for sure, you would have to check through the vin numbers

  • @edelindimitrov3922
    @edelindimitrov3922 ปีที่แล้ว

    What is the torque spec on the long bolt

    • @GaryFerraro
      @GaryFerraro  ปีที่แล้ว

      Never really looked that up, i just tighten it down snug and give a little extra and leave like that

  • @gokhanuzun1703
    @gokhanuzun1703 2 ปีที่แล้ว

    hello how are you i am writing to you from turkey w140 vehicle s320 1996 model gearbox 722.508 vietes transitions a bit hard, especially when switching to 3 and four, what is the problem?

    • @ebkonuk
      @ebkonuk 2 ปีที่แล้ว

      İlk once resetlemeyi dene.

    • @gokhanuzun1703
      @gokhanuzun1703 2 ปีที่แล้ว

      @@ebkonuk nasıl yapacağım

    • @ebkonuk
      @ebkonuk 2 ปีที่แล้ว

      How to reset Mercedes 5gtronic diye arat,bircok video goreceksin konuyla ilgili.Her zaman ise yaramayabilir,bu ilk asama...

  • @AhmedMohamed-hk3io
    @AhmedMohamed-hk3io 2 ปีที่แล้ว

    Great Job 👌 CGMB can help you a lot Gary for VGS virginize

  • @loganlefley1616
    @loganlefley1616 9 หลายเดือนก่อน

    My transmission suddenly stopped working. Very quiet whining sound when in drive and reverse. Neutral the sounds go away. Park and it makes loud sound like when you engage parking brake or use a ratchet but much louder. Car won’t move at all. 105,000km ?????????

    • @GaryFerraro
      @GaryFerraro  9 หลายเดือนก่อน

      So when you put the car in park, it rachets like there is something turning?

    • @loganlefley1616
      @loganlefley1616 9 หลายเดือนก่อน

      @@GaryFerraro it makes a ratcheting sound but only for a couple seconds. Sounds more like a hand brake but much louder. Like something tightening

    • @GaryFerraro
      @GaryFerraro  9 หลายเดือนก่อน

      Sounds like the output shaft is turning and it's ratcheting going into park , Do you know if the driveshaft is turning@@loganlefley1616

    • @loganlefley1616
      @loganlefley1616 9 หลายเดือนก่อน

      @@GaryFerraro I don’t know if the drive shaft is turning. I think it might be free though because I jacked the car up and the car started moving away like it was in neutral

  • @marlonredstar-yj2nb
    @marlonredstar-yj2nb 5 หลายเดือนก่อน

    How do i get you to rebuild my transmission ? Are Get a quote

    • @GaryFerraro
      @GaryFerraro  5 หลายเดือนก่อน

      where are you located?

    • @marlonredstar-yj2nb
      @marlonredstar-yj2nb 5 หลายเดือนก่อน

      ​@@GaryFerrarobillings Montana

    • @GaryFerraro
      @GaryFerraro  5 หลายเดือนก่อน

      @@marlonredstar-yj2nb you have a 722.9?

    • @marlonredstar-yj2nb
      @marlonredstar-yj2nb 5 หลายเดือนก่อน

      Yes, 2012 c300 sport v6 4matic.@@GaryFerraro

    • @marlonredstar-yj2nb
      @marlonredstar-yj2nb 5 หลายเดือนก่อน

      Yes

  • @AsifAsif-xk9nt
    @AsifAsif-xk9nt 2 ปีที่แล้ว +1

    Your camera please update we don't see clear

  • @michaelgillette7363
    @michaelgillette7363 2 ปีที่แล้ว

    Brand: Exedy
    Part Number: A78542
    Description: Pump Plate; Fits in Bell Housing Pump Pocket
    Transmission(s): 722.6, NAG1, 722.9, W5A580, W5A380, W5J400, 722.901, 722.666
    Years: 2004 - 2018 $33.61

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      Thats the plate when the bellhousing is damaged correct

  • @iamher6422
    @iamher6422 2 ปีที่แล้ว

    So what should one expect to pay for such a job? Good job, though… 😵‍💫

    • @GaryFerraro
      @GaryFerraro  2 ปีที่แล้ว

      on this one it's up there around 5K