Use a biquad, The way you did that antenna is ridiculous and it does not fit within the focal point correctly. You would have much better signal with a proper antenna that is directly focused within your focal point
Cool but only works to a point. It allow it to receive but it output power dosent change. It be like yelling to someone with a periodic dish which amplified the low sound an have them tell back but you don't have that dish
IF the output from the transmitter is +20 dBm, and IF the antenna element are tuned to 2.4 or 5 GHz, AND the SWR in the line from TX to antenne is ok, AND if the antenna elements is in the focal point of the dish, then the output from the antenna would be something like: +20 dBm (TX) -3 dB (cable loss)+ 30 dBi (antenna gain) = around +47 dBm EIRP. That is 47-20 = 27 dB gain, that's like 500 times stronger to the air than what comes from the transmitter (= around 40W transmitted from the dish) ----------------------------------------------------------------------------- ЕСЛИ выходной сигнал передатчика составляет +20 дБмВт, и ЕСЛИ антенный элемент настроен на 2,4 или 5 ГГц, И КСВ на линии от TX до антенны в порядке, И если антенные элементы находятся в фокусе антенны , тогда выходной сигнал антенны будет примерно таким: +20 дБм (TX) -3 дБ (потери в кабеле) + 30 дБи (усиление антенны) = около +47 дБм EIRP. Это 47-20 = 27 дБ усиление, это примерно в 500 раз сильнее для воздуха, чем то, что исходит от передатчика (= около 40 Вт, передаваемого с антенны). Простите за ненормативную лексику!!!!
@@coccobill7982 that on one side of it. If your using equipment like say a phone or a laptop at 3 building over then that device will see your transmitter but won't have the output power to talk to it keeping in mind wifi at 802.11 a(x) or n is like 90 meters +/- . What signals your transmitter might get is hit an miss an a lot of noise. Now say you make a portable one to carry with you for your laptop then yes you can point it to your dish if your with in it degrees of line of sight.
I'm on the fence on this one. Using a dish and an LNB as a mount for Wifi antennae does make sense. I run about 5W to a 1m dish on 2.4GHz to communicate through the geostationary QO-100 satellite (narrow band SSB transponder) with a 3.5 turn helix. The elevation angle shown seems suspect - it will be pointing towards the sky. But has given me an idea for a project.
Not sure about that parallel connection, maybe if the lengths were scaled to be 1/4 wave apart it would do circular / mixed polarization. Also, the antennae are quite some way off the focus, so it would squint, and it's quite likely the direct and reflected signals would not be in phase. I think this may be another "any bit of wire gets a signal" antenna in reality
@@matthewday7565 ever seen a cantenna? Wifi spot antenna made from a Pringles can. Used to use one back in the day while playing around with Backtrack3 across from an apartment complex.
@@fauxque5057 i used cantenna i've used the pringles kind and the menudo kind as well as the bean type of can hooked it to sat dish and viola' boosted my wifi and found some open wifi from hotels. great minds think alike 👍
People making fun of this, should know that it would actually work. The dish would not be pointed towards the sky but laterally in the direction of the wifi ap.
No it wouldn't, an LNB and its feedhorn are mounted at the focal point of a parabolic reflector dish so that the low power RF signal coming from a specific direction is reflected from every point of the dish face in phase constructively into the feedhorn which then acts as a low impedance waveguide to direct the concentrated RF signal to two cross polarised antenna probes at the back which are connected to the actual LNB which is a low noise block down converter, its an electronic circuit board that is gone here. The angle of the dish with respect to the direction the RF is coming from and the positioning of the feedhorn are critical if the are even slightly misaligned then the RF signal will be reflected to the feedhorn out of phase deconstructively which degrades it and makes it unusable, move your satellite TV dish slightly and you will see how sensitive it is. He's just using the empty LNB housing and the feedhorn here as a mount for the two little antennae set up as a V dipole he could have just mounted them on the mounting arm without the LNB box.
Converting a LNB into a wifi antenna does not requieres a dish... i can convert my flashlight.... remote control... what ever into an wifi antena... this video makes no sence.
Just having the untuned antennas above the center point creates a singnal loss. The untuned "V dipole" makes it worse. It could be so much better. You'd be better off taping a usb wifi dongle in front of the feed horn. Done!
And another award for 'So Close Yet So Far Away". Nice try. The antenna needs to be cut to frequency and centered where the LNB is. These rabbit ear antennas are not optimum.
You'd be far better off just strapping any kind of real WiFi antenna at the focal point of the dish.. That mess that he constructed isn't tuned for anything close to 2.4 or 5Ghz...
He is obsessed trying to convince everyone he is making antennae out of an LNB, but its just the empty housing and the feedhorn which are doing nothing, the chance of getting that little V dipole antenna positioned properly at the focal point of the dish so that the RF reflects to it constructively in phase are zero, it will be degrading any signal there is.
It's completely fake investing time in this is waste better you purchase external antinna 5 G is still year late to get fully deployed , wasting mone will only leave you disappointed and loosing your current network status
It's completely fake investing time in this is waste better you purchase external antinna 5 G is still year late to get fully deployed , wasting mone will only leave you disappointed and loosing your current network status
If you removed lnb pcb it's no Longer lnb , It will be great mod if you Use it's Amplifier by bypassing Filter as Signal booster , Active amplifier amplification .
I hope all with private wifi networks activate security and add a hard to break password to it. We all need to do what we can, to stop hackers breaking in to our networks. This as a general advice, not as a comment to this spesific video.
Is it safe? Does it offer client isolation for all users? Static IP? Etc.. if safety sucks, this WiFi sucks too Brace for impact, you will get hacked by random people, for extending your WiFi range
This is bullshit！You can not simply parallel two 50ohms coaxial cable with out any Impedance matching.What you just made are 2 standard 1/4 lamda GP antennas in 2.4GHz band and they are pretty easy to find on almost every wifi equipment.
![[Re:all TREASURE] EP.6 in 방콕ㅣ🚩 쩡캠의 방콕 투어 빵 마이 와이 👍](http://i.ytimg.com/vi/uyFw-nItA_s/mqdefault.jpg)
Use a biquad, The way you did that antenna is ridiculous and it does not fit within the focal point correctly. You would have much better signal with a proper antenna that is directly focused within your focal point
Could you please give me guidance on where you found the cable wifi part?
what the name of the parts and the program name ..that parts beside the dish antenna ??
Bhai aapke jaisa engineer na paida hua hai. aur Na hoga.aap se bahut umeed hai.
I tracked railway wifi using this as the railway station is few miles from my home
Cool but only works to a point. It allow it to receive but it output power dosent change. It be like yelling to someone with a periodic dish which amplified the low sound an have them tell back but you don't have that dish
IF the output from the transmitter is +20 dBm, and IF the antenna element are tuned to 2.4 or 5 GHz, AND the SWR in the line from TX to antenne is ok, AND if the antenna elements is in the focal point of the dish, then the output from the antenna would be something like: +20 dBm (TX) -3 dB (cable loss)+ 30 dBi (antenna gain) = around +47 dBm EIRP. That is 47-20 = 27 dB gain, that's like 500 times stronger to the air than what comes from the transmitter (= around 40W transmitted from the dish)
-----------------------------------------------------------------------------
ЕСЛИ выходной сигнал передатчика составляет +20 дБмВт, и ЕСЛИ антенный элемент настроен на 2,4 или 5 ГГц, И КСВ на линии от TX до антенны в порядке, И если антенные элементы находятся в фокусе антенны , тогда выходной сигнал антенны будет примерно таким: +20 дБм (TX) -3 дБ (потери в кабеле) + 30 дБи (усиление антенны) = около +47 дБм EIRP. Это 47-20 = 27 дБ усиление, это примерно в 500 раз сильнее для воздуха, чем то, что исходит от передатчика (= около 40 Вт, передаваемого с антенны).
Простите за ненормативную лексику!!!!
@@coccobill7982 that on one side of it. If your using equipment like say a phone or a laptop at 3 building over then that device will see your transmitter but won't have the output power to talk to it keeping in mind wifi at 802.11 a(x) or n is like 90 meters +/- . What signals your transmitter might get is hit an miss an a lot of noise. Now say you make a portable one to carry with you for your laptop then yes you can point it to your dish if your with in it degrees of line of sight.
I wanted to create this in the year 2004 ☺️nice man
Connect hua h wo to nahi dikha kuch download karke batae 😅
I'm on the fence on this one. Using a dish and an LNB as a mount for Wifi antennae does make sense. I run about 5W to a 1m dish on 2.4GHz to communicate through the geostationary QO-100 satellite (narrow band SSB transponder) with a 3.5 turn helix.
The elevation angle shown seems suspect - it will be pointing towards the sky. But has given me an idea for a project.
Not sure about that parallel connection, maybe if the lengths were scaled to be 1/4 wave apart it would do circular / mixed polarization.
Also, the antennae are quite some way off the focus, so it would squint, and it's quite likely the direct and reflected signals would not be in phase.
I think this may be another "any bit of wire gets a signal" antenna in reality
I'm no te fancee on this one .sin a Dish and and lbn as a mount
@@matthewday7565 ever seen a cantenna? Wifi spot antenna made from a Pringles can. Used to use one back in the day while playing around with Backtrack3 across from an apartment complex.
@@fauxque5057 i used cantenna i've used the pringles kind and the menudo kind as well as the bean type of can hooked it to sat dish and viola' boosted my wifi and found some open wifi from hotels. great minds think alike 👍
@APPS yes in deed my brotha
People making fun of this, should know that it would actually work. The dish would not be pointed towards the sky but laterally in the direction of the wifi ap.
No it wouldn't, an LNB and its feedhorn are mounted at the focal point of a parabolic reflector dish so that the low power RF signal coming from a specific direction is reflected from every point of the dish face in phase constructively into the feedhorn which then acts as a low impedance waveguide to direct the concentrated RF signal to two cross polarised antenna probes at the back which are connected to the actual LNB which is a low noise block down converter, its an electronic circuit board that is gone here. The angle of the dish with respect to the direction the RF is coming from and the positioning of the feedhorn are critical if the are even slightly misaligned then the RF signal will be reflected to the feedhorn out of phase deconstructively which degrades it and makes it unusable, move your satellite TV dish slightly and you will see how sensitive it is. He's just using the empty LNB housing and the feedhorn here as a mount for the two little antennae set up as a V dipole he could have just mounted them on the mounting arm without the LNB box.
correct-a-mundo hooked cantenna to my dish and boosted my wifi signal pointing it lateral 👍
Converting a LNB into a wifi antenna does not requieres a dish... i can convert my flashlight.... remote control... what ever into an wifi antena... this video makes no sence.
Just having the untuned antennas above the center point creates a singnal loss. The untuned "V dipole" makes it worse. It could be so much better. You'd be better off taping a usb wifi dongle in front of the feed horn. Done!
And another award for 'So Close Yet So Far Away". Nice try. The antenna needs to be cut to frequency and centered where the LNB is. These rabbit ear antennas are not optimum.
I did it for myself and now I'm receiving signal from mars with the speed of 500TBPS
Cool Dude
Lol
*awokawokawok*
Nhận được tín hiệu từ hành tinh khác anh ạ
😂😂
Zip ties would work better for long term usage
exact-a-mundo but thats all he had. you could use thin wires too to wrap
Tengo la pantalla de directivo me gustaria poder hacerla funcionar antena h d televisión como conectarla
2:13 what type of cable is that?
Where can I get the USB device u used.
What's the names of the gadgets u used . I wanna try it
Tp link 722
Nomás se ve el vídeo y ruidos pero no Disen q piezas son ni nombres de lo que c nesesita nada
You'd be far better off just strapping any kind of real WiFi antenna at the focal point of the dish.. That mess that he constructed isn't tuned for anything close to 2.4 or 5Ghz...
exactly
I was thinking this, but more strapping to the focal point on the lnb reciever, perhaps even a very small USB pip inside the lnb
I would use the probes that are already in the LNBF.
He is obsessed trying to convince everyone he is making antennae out of an LNB, but its just the empty housing and the feedhorn which are doing nothing, the chance of getting that little V dipole antenna positioned properly at the focal point of the dish so that the RF reflects to it constructively in phase are zero, it will be degrading any signal there is.
Sayang TDK jelas nama peralatan yg serupa USB jadi bingung !
Can I use this antenna to receive 4G for my phone
Most of this stuff doesn't work,for entertainment purposes only.
Time pass and view😂😂*
You are the Nobel award winner 😁 don’t loose your time any more
Mejor evito todo ese trabajo y utilizo una USB WIFI con antena interna, y la coloco dentro del LNB , utilizando una extensión de cable usb.
Been wondering i seen only Spanish tv ? Does it have regular tv channels
Agar aise wifi banakar chalne laga to jio/airtel ka kiya hal hoga yato taiwan ko bhi pichche kar denge
This is EXACTLY what I need a video on. Thank you so much.
It's completely fake investing time in this is waste better you purchase external antinna
5 G is still year late to get fully deployed , wasting mone will only leave you disappointed and loosing your current network status
do-as-you-please lengths?
I was able to do this and get internet from Japan now I'm getting 500mbs thanks for the tutorial 👍
Really Is it work?
Thanks for showing me what's inside that transceiver
😂😂😂😂😂sarcasm
@dinesh rathod he is making fun of it
😂
It's completely fake investing time in this is waste better you purchase external antinna
5 G is still year late to get fully deployed , wasting mone will only leave you disappointed and loosing your current network status
If you removed lnb pcb it's no Longer lnb ,
It will be great mod if you Use it's Amplifier by bypassing Filter as Signal booster , Active amplifier amplification .
Then that PCB will need 12v constant power supply how it will be provided? it will ruin the whole purpose of DIY fun..
@@atifzaidi8198 same wire can be use for power and Supply
you only converting a LNB into an antenna... The dish doesnt make any sence.
@@gmcmoosthe dish can reflect the signal to the 2-stick antenna. that can provide higher gain.
I hope all with private wifi networks activate security and add a hard to break password to it. We all need to do what we can, to stop hackers breaking in to our networks. This as a general advice, not as a comment to this spesific video.
Can lnb burn or strikes b lightning
how could not be any password needed on the networks? how is it that they are all open?
Получилось хоть что нибудь ???
As u are showing thing, do we have to connect the centre box
भाई कम से कम बोल कर बताओ आपने इस एलएलबी के नीचे क्या क्या लगाया
What material do you used? Please notice. Thanks
He is teasing us
This is provided for entertainment purposes only
bro, sorry, give details of the tools used and the exact address of the signal, I can get it for free like yours
Now i have to unsee it 😭😭😭
Nice 👍
Can we use it for extender?
only one difrence to mikrotik's LDF 2 or 5- Mikrotik just works
Fin nqder nlqa dk lhigh gain ?
Connect ho raha h 😂 pc me
i thought i just heard you fart at 2:38
Is it safe? Does it offer client isolation for all users? Static IP? Etc.. if safety sucks, this WiFi sucks too
Brace for impact, you will get hacked by random people, for extending your WiFi range
No its not safe it needs CIA FBI & FDA Clearance 😂😂😂😂
*NOT*
Very nice...
The bigger the glob, the better the job? Hard to take serious when your soldering skills are so horrible.
Is it free or just attracting views
Baavlaa bnne KE liye HM Hi Mile H Kya
Who said nirav modi is biggest scammer there is biggest scammers than him on TH-cam which waste viewers time and data regularly.
May video 📸 biutyfull Suresh penter hatwa
I want to make a USB wifi but I need more guidance on whether it will work. Can you be reached via email?
plenty of videos showing that procedure
For subscribers purpose only.
Without recharge it will bro
It’s not working...
I always learn somthing new watching this channel. Mostly everything here is new information, that is not seen elswhere.
Where can I buy one?
I try bro wathing from philipines
Canwe convertoldanttenaintoawifi
Estou preparado para contatos com aliens do passado ou eu futuro 😂😂😂
Thank you for the explanation, it can be an alternative for me to continue learning to work🥰🙏👍
СПУТНИКОВЫЙ конвертер + USB modem
4g kabel LAN WIFI роутер
Nice video clip, keep it up , thank you for sharing :)
Di mo pinakita lahat.....
Woooh fake technicians
That’s a bird
👍👍👍
Atcha huua
Oh its u who hacked my wifi from 10290 km , oh god save me plz from this space guy 😭
Fake
I did it and I am receiving signal from Mangal Graha
This is a old schools scammers technique
And also pigs can fly.............
Anh oi làm anten bắt tín hiệu từ hành tinh khác à
Có bán ko a
Great 👍👍👍👍
This is really working or a joke?
Good idea I guess, but never saw such sloppy assembly and poor soldering technique. I'm really surprised it worked.
Soldring is good
@dave ward have you ever holded a solder iron yourself?😂😂he did good and robust soldering
@@atifzaidi8198 I've been soldering for over 50 years.
Motion
ET phone home 🤭🤭🤭🤭 It's amazing that someone spends so much time making something that does not work! And someone thinks this works 😂😂😂
Thank you
Cool Dude
Very sloppy work.
Oh my it's works ya I received signal from Aliens
Go Bonkers
Wastage of time not completed.
This is bullshit！You can not simply parallel two 50ohms coaxial cable with out any Impedance matching.What you just made are 2 standard 1/4 lamda GP antennas in 2.4GHz band and they are pretty easy to find on almost every wifi equipment.
Obviously doesn't have any clue what means RF and impedance match. All this built is it BS.
Dish is used as reflector. It would work better if focused to center of dish. Lnb has nothing to with design apart from holding the cables.
@@evertspies3345 exactly that cables is the problem......
I would use the V and H probes that are already in the LNBF.
😂😂😂 i am pretty sure you don’t know about electromagnetic radiation.
👍👍👍👍👍👍
Just trashed a good lnb.
U dnt need to hack lnb 😂😂 u can directly mount single antenna on dish and u will get same result ….. or just using aluminum foil paper 😂😂😂😂
Shitshow
a stupid antenna
😂😂😂😂😂
ЦИРК!
Ye sab bevkoof bnanane ki trik hhh
Give me details
Ghanta chutiyapa band karo