A mechanic shop quoted me: Valve cover full kit $600 Spark plug tube $ 72.54 (6 x $12.09) Spark Plug $168.24 (6 x $28.04) Labor $1260 Tax $200 The total price for the valve cover kit and 6 spark plugs with tubes = $2322.58 I can do the spark plugs easily so I don't know why I was quoted that when I just need valve covers only. That's about $1000 for valve cover labor? That seems crazy from a non-dealer mechanic shop. I am going to do this myself watching your video! I've seen valve cover kits around $80-$120 on Amazon and eBay
Hi, My bmw E83 crankcase vent valve went bad with pressure in engine & blow out my valve cover gasket. Do you think it could have damage any other seals?
It could damage the rear main seal or the front main seal. You really cannot tell unless the job is done and the engine is clean and then you look for more leaks.
You mean the valve cover it self? I honestly don’t see why he want to change the whole cover unless the cover is cracked or has a problem, you don’t have to change it.
@@enriquedavalos9170 also you can get the small plastic Zip ties and cut 2-3 strips 1/4in each and insert them where the bolt goes then install the bolt back. It should hold very well. Or you do it right and drop a Helicoil in there.
i recommend replacing the entire valve cover and the gaskets. over time the valve cover expands and contracts. it's plastic cover that expands and contracts.
A mechanic shop quoted me:
Valve cover full kit $600
Spark plug tube $ 72.54 (6 x $12.09)
Spark Plug $168.24 (6 x $28.04)
Labor $1260
Tax $200
The total price for the valve cover kit and 6 spark plugs with tubes = $2322.58
I can do the spark plugs easily so I don't know why I was quoted that when I just need valve covers only. That's about $1000 for valve cover labor? That seems crazy from a non-dealer mechanic shop. I am going to do this myself watching your video! I've seen valve cover kits around $80-$120 on Amazon and eBay
What brand of tools do you use? Specifically the electric torque wrench
SnapOn
Hi, My bmw E83 crankcase vent valve went bad with pressure in engine & blow out my valve cover gasket. Do you think it could have damage any other seals?
It could damage the rear main seal or the front main seal. You really cannot tell unless the job is done and the engine is clean and then you look for more leaks.
thank you
Hi one of the bolts doesn’t tie just keeps spinning, is leaking oil. Any recommendations?
My mechanic says don’t bother replacing the gasket and do the whole valve itself which is far more expensive .. any thoughts ?
You mean the valve cover it self? I honestly don’t see why he want to change the whole cover unless the cover is cracked or has a problem, you don’t have to change it.
@@a2zautomasters862depends on age and mileage. PCV valve is a known failure on the N52 and it's integrated into the valve cover.
@@omarpulido8502 that’s true and it causes failures on seals and gaskets bc of the pressure inside the crankcase causing major oil leaks.
Hi, one off the bolts is spinning, do I tie too hard and now is broke, or do I put too much sealant?
One of the bolts that holds the valve cover?
@@enriquedavalos9170 also you can get the small plastic Zip ties and cut 2-3 strips 1/4in each and insert them where the bolt goes then install the bolt back. It should hold very well. Or you do it right and drop a Helicoil in there.
@@a2zautomasters862 yes it was the one that holds the valve cover.
We ended up making the new thread.
What is the hose in the back called? The one you have to super careful with.
It’s the PCV hose.
I think I'll just buy one cause knowing my luck I'll break it lol
@@michaelgilman2691 lol
How long did it take to install?
Rated for probably 4-5 h can be done in 2 1/2
I just got mine and it’s a 2007 bmw 328 do I have the Same issue I can smell it burning then I stop smelling it it has small oil leaks
Take a look on the pass side of the engine and back if you see any oil leaking on the exhaust manifold there, most likely you have to change it. 👍🏻
What priduct did you use to hold the gasket in place?
3M yellow super weatherstrip and gasket adhesive
Can I do it without it?
@@simplysane2090 - You need something to keep the gasket in place when you turn the cover upright.
i recommend replacing the entire valve cover and the gaskets. over time the valve cover expands and contracts. it's plastic cover that expands and contracts.
It’s true, Just depends on the condition of the cover and how many miles on the car.
I would like to attempt this but how much would it normally cost to have it done? Thank u
It’s a 5h job by the book multiplied by the shop rate plus parts. $600-800 or so
@@a2zautomasters862 ok thank you very much. I really appreciate your honesty
🛠🛠🛠🛠🛠....Sorgfaltige Arbeit!🔬✅👌🏼
The king of cars ❤💪❤
Abdo Adel my brother. 👍🏻
Thanks man!
👍🏻💪🏻🙏🏻🙏🏻🙏🏻