Was thinking of connecting two of these (one normal, one "dead") myself, done similar stuff before, but this reassured me and now the dead one is charging. Thanks for this kind of videos, as better to use stuff laying around to fix it than throw it away.
Good way to bring batteries back to life. I have already tried the 1st trick on different batteries. Successfully! But then I connect the cables for 10 seconds and then I immediately put the battery in the charger. I have tried different brands, including Gardena, Parkside and Bosch.
Браво добро и образователно видео, аз периодично ги балансирам клетка по клетка след 10 цикъла почва някоя клетка да изостава. Незнам при марковите батерии така ли е, но при Паркасайд е така по мои наблюдения.
Благодаря🙏🙂 Аз имам 7 батерии, от време на време ги проверявам клетките, разликите им са от потядъка на 0,01 - 0,03V и до сега не ми сеналагало да ги балансирам. Но когато купих винтоверта със алуминиевия куфар, преди 1 или 2 години, при тестване мощността на винтоверта мисчя, че прецаках 1-та батерия защото 2 от клетките му са вече със капацитет около 1200mAh. Изводът от това е 2Ah батериите са само за зелената серия.
Well, one of my 4Ah Parkside batteries wouldn't charge, so I connected it to a known good 2Ah battery (minimizing replacement cost...) Left them outside, connected together for half an hour, both charge indicators showed "full" after that, but they did accept a few minutes charge. Must see if the 4Ah job performs OK now. I bought a couple of adaptors for Parkside batteries, and they make connecting batteries together so easy...
0.5mm² or 0.75mm² are enough but if your battery is drained more, just add a 55W headlight bulb between one wire so the current flows through the bulb so it doesn't charge with high current which can damage the cells. And don't leave the batteries unattended while doing this!!!
Hi! The first method work when I have 2 different type of battery? I want to use my 20 V battery to recharge my bad 16 V. Both of them Parkside product. Many Thanks!
J'ai eu le même problème j'ai branché la batterie défectueuse normalement avec son chargeur sur un inverteur 600 watts alimenté avec 2 batteries de voitures 72Ah*2, je vous assure ça à réveillé tout le monde dans la batterie je n'ai pas compris pourquoi ça a résolu le problème depuis plus aucun soucis ! La batterie charge complètement en 10 min chrono avec ce procédé désormais 😃👌
@@igotbricotools2035 It does not need to be recharged every month. Just by putting this battery in the screwdriver didn't work. There may be a problem with BMS balancing or a bad cell. Otherwise, I don't care about the other batteries, I charge them when it occurs to me. For example in 6 months maybe more🙂
@@ErCanEverything i have batteries that i dont use. For example the black drill that comes in a aluninium box, comes with two 2 ah batteries i never used. Im gonna give them a quick discharge with the air heater and a charge
I don't think there will be a need for discharge, but if you are going to store it for a long time, it is recommended that the batteries be 60% charged. And this function have in the new smart charger and this is good function
Thanks. I had a 4ah down to ~5v (measured between + / - on the battery itself). The charger wouldn't charge it and both lights blinked. The charger doesn't even output power when plugged into socket, until apparently it 'talks' to battery to do some form of a handshake (I guess board in battery has to give OK to be charged or charger doesn't start when voltage of battery is below certain level). In my case I connected 2ah (fully charged) to the dead 4ah twice for ~40m each time. Then the dead 4ah (showing now green + yellow on the capacity indicator) still wouldn't start charging. Put it on a cordless drill and ran the motor couple of times. Then attempted to charge it again and miracle - it started charging.
Basically, 18V and 20V batteries consist of 5 cells. That is, the nominal voltage of both batteries is 18.5V, but Parkside decided to mark them as 20V. Battery capacity doesn't matter but to be safe make the current flow through some kind of consumer eg H1 lamp but should not be left unattended!!!
Does it means that battery is defective or this is something that just happens from time to time? Since I had same issue and this hack worked but since it's under waranty I will replace it if this means it's defective? Thanks in advance!
Благодаря ! И аз имам такъв проблем с лидълска 4 амперчасова батерия, но не можах да си намеря касовият бон, за да я върна. Ще опитам да реша проблем по Вашата методика.
@@ErCanEverything I have a 4ah battery PAP 20 B3/2022/03. Cells are balanced. They differ by 0.001v, but the battery does not charge. The LED on the charger is flashing.
Hi, do you have experience with a Parkside battery that doesn't want to fully charge? When I press the battery indicator only two out of three lights appear, although the battery have been just charged. I read somewhere in the comments that I need special Parkside charger to fully charge my battery, but I don't believe this, is it true? I still have original charger, although it's the entry level charger. Maybe my light indicator on the battery is defective?
And there is a problem with balancing speed... most pcb boards do balancing very slowly .. It is designed to balance during every charging so if you dont use battery for very long time cells might go out of balance very badly.. Then when you put it on charging it could take days to fuly balance every cell... Thats why it is better to manualy charge every cell group to same voltage.. That way you basicly do manual balancing faster than pcb board , you bring cells basicly to similar voltages and after that electronic board can take over and keep battery balanced (if you use it from time to time ofcourse)
@@ErCanEverything I dont know..i dont have experience with makita , its probably some communication port connector... Im not even sure if parkside old gen batteries can even balance.. I was talking in general that balancing takes long time on very bad disbalanced cells.. but who knows if parkside battery even balance her self while charging.. :D I never tested it... New batteries can balance for sure , they are much "smarter"but old ones... who knows..
Just put the battery into a 12v battery charger using the right pins and after 2 minutes the lidl charger can start charging the battery. Brought to life 20 baterries so far nothing blew up
If the red en green light is blinking. And I leave it for a day or 2 will be the battery self balance again? I just bought a new accu and this is what I get.
I have a PAP 20 A3 2020-03 battery from which I made a 20,000mAh Power Bank that has no discharge protection and several times discharged to a critical level and did not charge. In the evening I left it in the charger and in the morning I see that it has been charged. I mean, it turned out to be a very successful battery. th-cam.com/video/vRydMn5B3CM/w-d-xo.html
Такова разбалансиране на клетките се получава най често при зареждане на батерията при ниски температури под 0°C. Възможно е да стане и при претоварване на батерията, батериите 2Ah трябва да се товарят максимум 10-12A самите клетки издържат до 18A но загряват доста при този ток. Този метод не го знаех, аз премахвах балансиращата платка на батерията и зареждах клетките една по една и после отново запоявах балансиращата платка. Но този метод е по лесен би трябвало да стане и с обикновен регулируем токоизправител като му се зададе 21V в конкретния случай с тази батерия на парксайд. Следващия път като имам такъв проблем ще проверя и този метод. Благодаря за видеото.
Може да се заредят без да се разпои платката, но при разбалансирани клетки трябва да се заредят един по един. Когата им захраниш общо със 21V, пак няма да се балансират или трябва да се изчака много докато платката ги балансира. Най добрия вариант е зареждане със 4,2V и максимум 2-3A
There should be some kind of low voltage cut off device to protect the battery from this; such low voltage cut off can be either in the battery itself or in the device that is supplying the load to the battery.
I have one that been drain down from the grinder won't charge anymore any idea how to fix this I did try the loop from another battery but still don't want to charge
I have a battery that does take charge (the lights do not blink on the charger). However the battery drains after a few seconds, and some powerful tools will not even power on. It is a 4Ah of the newer model with cell balancing. I got a new one on warranty, but I got to keep the old one. Is there anything I can do with this?
My 20V Pack from Parkside (old Gen.) only shines the orange light (in the middle of green and red) when I press the test button and also doesn't charge - Could you please tell me what could be wrong here? Best Regards Toms
BEWARE of using older parkside batteries on other tools, all 20v parkside tools have a bms and cell balancing, BUT it does not test or prevent over discharge, if you over discharge a parkside battery, the protection chip in the battery will lock out the battery forever! it will not send 'handshake' to charger to start charging. its a safety feature of the bms IC to protect us from fire, not to increase company profit.. also recharging the cells 1 by 1 will not unlock it I have spent hours doing this, I have tried many parkside boards etc as I built a full 50mph+ e-motorcycle from parkside cells so i have a lot of the boards
Problem solved but it's mean that cells in this battery are very different. At least that one with voltage under 3v. And future life of the battery won't be long.
@@ErCanEverything I know, from my experience that this is a 'chain reaction'. The cells, at least those from older batteries (although yours is not old, from 2020) are not really high-current and especially in 2ah sets they are damaged or, like this one - degraded.
strange, I was expecting that this electronic circuit inside battery (controler and balancer) should take a care that each cell is equally charged. Seems that it is not balancer but some sort battery life limitator 😂
it might be balancing but the battery hasn't been used for over 1 year and I used on 80Nm performance drill and the battery died in about 5 minutes. Apparently the cells have malfunctioned
@@zokonjazokonja if out of balance it will charge and balance, if out of balance a great amount then it considers that to be too dangerous. if a cell goes
@@lezbriddon It make sense. But this problem could be also solved by reducing charging current (slow charge), best way would be to somehow tell charger to decrease charging current. But thos would require some higher level of communication between balancer and charger.
@@zokonjazokonja there's 2 way comms on the third pin between chip in battery and chip in charger so it could be done, but I think the chips are programmed by the mystery supplier, I have never found a real data sheet or what the comms data means, I can watch it on my oscilloscope and i can force changes into it by heating the battery thermister but have no idea what the packets mean. its not a lidl chip i know other companies use it too like anker
grazie mille posso salvare la mia batteria PKS anche solo con un altra o serve tutta quella attrezzatura? Il mio aspirapolvere Roomba con batteria nuova (80 euro :( ) è morto dopo che è rimasto senza caricare per 20 gg, posso recuperare? grazie
it's a bit risky because a 24V charger generates 28.8V. But if you make the current pass through some kind of load resistor or some kind of lamp and monitor the voltage to the battery, it shouldn't exceed 21.6V
Aynı sorun bendede oldu Bozuk bataryayı iki adet araba bataryası (72 Ah*2) 600 watts bir invertöre normal şarj aleti ile bağlayarak şarj ettim ve sorunu hallettim nasıl neden düzeldi anlayamadım ! Batarya artık bu yöntem ile 10 dakikada ful doluyor 😃👌
hello i have same problem. but im in willage and i dont have second cordless drill or etc. and i dont have tool you have so is there any other way to solve this problem. like charge it with 220 to 12v adaptor or somthing like this. i have only two batteries car battery and tv remote 😂😂😂
This is great video, you helped me a lot. I saved dead battery.. Greetings from Croatia.
I'm glad if I was able to help you🙂🤝
@@ErCanEverything à
I ja isto :))
It helped to my battery too.
Within only 1 minute balancing with other battery, it started charging again ! Thanks a lot !!
Was thinking of connecting two of these (one normal, one "dead") myself, done similar stuff before, but this reassured me and now the dead one is charging. Thanks for this kind of videos, as better to use stuff laying around to fix it than throw it away.
Good way to bring batteries back to life. I have already tried the 1st trick on different batteries. Successfully! But then I connect the cables for 10 seconds and then I immediately put the battery in the charger. I have tried different brands, including Gardena, Parkside and Bosch.
Esto es todo falso
Thank u so much for this hint! My battery geting the charge again!
Greetings from Hungary ✌️
I am very glad that I was able to help with something🙂
Greetings from Bulgaria👋
Great fix, saved me buying a new battery, keep up the good work!
I'm glad I was able to help you🙂
Thank you for good wishes my Friend🙏🤝
Thanks. Thanks to this video I revived a dead 4AH battery.. GREAT..
I'm glad I was able to help you.😊🤝🤝🤝
Bu yöntem işe yaradı çok teşekkürler 2 kablo işimi gördü çok sağolun .
Thank you very much for this video, it has helped me save two batteries which would not take a change.
I'm very glad I could help you🙂🤝
Great i have one battery with same problem, now i am going to fix it, thanks you mate 🙏🙏🙏
Remember, the battery must be fully charged to have a quick and full effect🙂
Hi! Thanks a lot this is great video, you helped me a lot. I saved dead battery.. Greetings from Hungary!
I'm happy if I did any help🙂
Greetings from Bulgaria🙂🤝
Merci, cette méthode m'a résolu le problème
I'm glad if I was able to help you🙂🤝🍀
Thanks dude your video helps me alot 🍀🙏💪
Wow! It actually worked. Thanks alot. 👌👍
Браво добро и образователно видео, аз периодично ги балансирам клетка по клетка след 10 цикъла почва някоя клетка да изостава. Незнам при марковите батерии така ли е, но при Паркасайд е така по мои наблюдения.
Благодаря🙏🙂
Аз имам 7 батерии, от време на време ги проверявам клетките, разликите им са от потядъка на 0,01 - 0,03V и до сега не ми сеналагало да ги балансирам.
Но когато купих винтоверта със алуминиевия куфар, преди 1 или 2 години, при тестване мощността на винтоверта мисчя, че прецаках 1-та батерия защото 2 от клетките му са вече със капацитет около 1200mAh. Изводът от това е 2Ah батериите са само за зелената серия.
Worked like a charm!!!
Hi, this Idea ist great and it works very well! The first tip was successfully.
Well, one of my 4Ah Parkside batteries wouldn't charge, so I connected it to a known good 2Ah battery (minimizing replacement cost...) Left them outside, connected together for half an hour, both charge indicators showed "full" after that, but they did accept a few minutes charge. Must see if the 4Ah job performs OK now. I bought a couple of adaptors for Parkside batteries, and they make connecting batteries together so easy...
Worked perfect for me thanks
GREAT 👍👍👍 material. You helped me a lot with this video.
I'm happy if I did any help🙂🤝
Worked for me. Thanks! 😃
Thanks it did work ❣️
your video helped me save my parkside battery (one cell needed revival) . many thanks !!
I'm glad if I was able to help you🙂🤝🤝🤝
Excellent! Worked a charm. Thank you very much.
Thank You very Much🙂🤝
Thanks, saved my battery!!
Glad I could help you man🙂😇🤝
Thanks, the battery is fixed!
Thank you for the back video
Awesome thank you ❤️
Lol this works. 🎉 Well it is charging now.
Thanks. Worked for me by charging a 2A from a 4A.
Köszönöm,két akkumlátorom újra működik :)
I'm glad if I was able to help you🙂🤝
Didn't know I can charge every cell separatelly without desoldering them, thx.
tesekur abi maasallah very accurate and clean work...i learnt
alot.
Thank you🙂🤝
Thank you for the help
NO FCKN WAY THIS WORKED!!!! THANKS BROTHER ! DEFINITELY SUBSCRIBING
Thank you, this may save a few batteries for me.
a great tool....thanks for sharing bro
Nice 👌
Thank you🙏🤝
Welche Kabel braucht man dafür? Kenne mich gar nicht mit Elektronik aus...
0.5mm² or 0.75mm² are enough but if your battery is drained more, just add a 55W headlight bulb between one wire so the current flows through the bulb so it doesn't charge with high current which can damage the cells. And don't leave the batteries unattended while doing this!!!
Hi!
The first method work when I have 2 different type of battery? I want to use my 20 V battery to recharge my bad 16 V. Both of them Parkside product.
Many Thanks!
Thank you very much
J'ai eu le même problème j'ai branché la batterie défectueuse normalement avec son chargeur sur un inverteur 600 watts alimenté avec 2 batteries de voitures 72Ah*2, je vous assure ça à réveillé tout le monde dans la batterie je n'ai pas compris pourquoi ça a résolu le problème depuis plus aucun soucis !
La batterie charge complètement en 10 min chrono avec ce procédé désormais 😃👌
Thanks!!!!
What is all the equipment you're using to fix it is it expensive?
Excellent 👏👏
I got many batteries . What should i do ? Used every 6 months ? Discharge and charge ?
This happened to me, even with perfectly balanced and charged cells. I just had to supply with another battery.
@@ErCanEverything do u mean a battery must be used every month if dont will go creazy ? 🤔
@@igotbricotools2035 It does not need to be recharged every month. Just by putting this battery in the screwdriver didn't work. There may be a problem with BMS balancing or a bad cell. Otherwise, I don't care about the other batteries, I charge them when it occurs to me. For example in 6 months maybe more🙂
@@ErCanEverything i have batteries that i dont use. For example the black drill that comes in a aluninium box, comes with two 2 ah batteries i never used.
Im gonna give them a quick discharge with the air heater and a charge
I don't think there will be a need for discharge, but if you are going to store it for a long time, it is recommended that the batteries be 60% charged. And this function have in the new smart charger and this is good function
Hi. Connected the broken battery with a new one for 5 min, and now the broken battery charges again. Many thanks
Salvou a minha bateria, um abraço desde Portugal 💪🏻
the best!! thanks
Thank you🙂🤝
Thank you!❤
Thanks. I had a 4ah down to ~5v (measured between + / - on the battery itself). The charger wouldn't charge it and both lights blinked. The charger doesn't even output power when plugged into socket, until apparently it 'talks' to battery to do some form of a handshake (I guess board in battery has to give OK to be charged or charger doesn't start when voltage of battery is below certain level). In my case I connected 2ah (fully charged) to the dead 4ah twice for ~40m each time. Then the dead 4ah (showing now green + yellow on the capacity indicator) still wouldn't start charging. Put it on a cordless drill and ran the motor couple of times. Then attempted to charge it again and miracle - it started charging.
Will this work with different voltage / amp batteries? I have a 4ah 20v dead battery and a 2ah 18volt good one
Basically, 18V and 20V batteries consist of 5 cells. That is, the nominal voltage of both batteries is 18.5V, but Parkside decided to mark them as 20V. Battery capacity doesn't matter but to be safe make the current flow through some kind of consumer eg H1 lamp but should not be left unattended!!!
Is it possible after couple of charging discharging cycles batteries to get balanced 🤔
Can this battery be used in tools or it needs to be balanced?
Will balance them after a few charges and discharges, but this will happen slowly.
Can be used in tools.
Does it means that battery is defective or this is something that just happens from time to time? Since I had same issue and this hack worked but since it's under waranty I will replace it if this means it's defective? Thanks in advance!
Hi, its seen y have also modified portable charger. Its something inside or only 2 wires with 21v?
Super Sache. Sprichst du deutsch?
Nein, aber du kannst mir gerne auf deutsch schreiben wenn du fragen hast kein problem. Vielen danke🙂
Funciona perfectamente! TKS!!!
is this battery work like an alternative battery for grizzly pro tools?
Благодаря ! И аз имам такъв проблем с лидълска 4 амперчасова батерия, но не можах да си намеря касовият бон, за да я върна. Ще опитам да реша проблем по Вашата методика.
Дано да се оправи защото при новите cell balancing версиите понякога не се получава.
@@ErCanEverything I have a 4ah battery PAP 20 B3/2022/03.
Cells are balanced. They differ by 0.001v, but the battery does not charge. The LED on the charger is flashing.
Thank you sir , can we do same without x12v team battery ?
X12V team battery with X12V team battery?
Yes you can🙂
@@ErCanEverything thank you it works , but I found that first charge after recovery is too long !???? I will see next charge is the same
Does the wire guage matter or battery size? I have a 80V and it sparked and melted stuff when I tried this.
Hi, do you have experience with a Parkside battery that doesn't want to fully charge? When I press the battery indicator only two out of three lights appear, although the battery have been just charged.
I read somewhere in the comments that I need special Parkside charger to fully charge my battery, but I don't believe this, is it true? I still have original charger, although it's the entry level charger. Maybe my light indicator on the battery is defective?
Funktioniert! Danke!
Nice video :) thanks.
So why can't a charger simulate the first method you used? It seems simple enough. Thanks for the vid!
The charger board does not charge until the BMS on the Battery does not allow it.🙂
And there is a problem with balancing speed... most pcb boards do balancing very slowly .. It is designed to balance during every charging so if you dont use battery for very long time cells might go out of balance very badly.. Then when you put it on charging it could take days to fuly balance every cell... Thats why it is better to manualy charge every cell group to same voltage.. That way you basicly do manual balancing faster than pcb board , you bring cells basicly to similar voltages and after that electronic board can take over and keep battery balanced (if you use it from time to time ofcourse)
Maybe that's why the Makita Batteries have a yellow balancing jack which is directly controlled by the charger when charging.
@@ErCanEverything I dont know..i dont have experience with makita , its probably some communication port connector... Im not even sure if parkside old gen batteries can even balance.. I was talking in general that balancing takes long time on very bad disbalanced cells.. but who knows if parkside battery even balance her self while charging.. :D I never tested it... New batteries can balance for sure , they are much "smarter"but old ones... who knows..
Can you do it with 16v and 20v batteries?
Teşekkürler sayende pil çalıştı
İşe yaradığına sevindim🙂🤝
Genial 👍👌💯👋👋🇪🇦
Thank You🙏🙂🤝🤝🤝
Nice 👍🏻👍🏻 🇮🇳 Kuki 31|05|2022
Where did u bought that charger ?
Thank you
Hi. i have a parkside battery of 18v 2.0AH, with that problem, brand new i must say. but only i have a different battery of 1.5AH 18V, it can work?
Yes
question....what device are you using (White ) to do this..what's it called...???..Thanks....
I used the Riden RD6018 power supply, which I made the case myself in my own style🙂
👉 th-cam.com/video/PL82cN_hNbk/w-d-xo.html
the most sensible solution is to take the connections outside and charge all the cells at the same time with a model charger
The Cell dropped to 2,95 will be always unbalanced compared to the other or not?
I wonder if we can make a 12v refrigerator a way to work with rechargeable style parkside battery! That woud be an inovation!
It is possible but these refrigerators consume a lot of current around 4~8Ah and will drain the batteries very quickly.
@@ErCanEverything It would be ok if you have 2-3 of 4ah to use! Thank you for your response!
Just put the battery into a 12v battery charger using the right pins and after 2 minutes the lidl charger can start charging the battery. Brought to life 20 baterries so far nothing blew up
Where is the smart charger available to purchase trawled the net and found nothing please and thank you
Lidl.de
www.lidl.de/p/parkside-performance-akku-ladegeraet-smart-plgs-2012-a1-20-v-12-a-ueber-lidl-home-app-steuerbar/p100339802
Lidl.es
www.lidl.es/es/cargador-de-bateria-smart-20-v-/-12-a-300-w/p51521
Fantastic thanks great vid saved one battery just need to balance the other one then hopefully it will be ok
Merci je vien de résoudre le problème sur batterie festool
Exactly my problem
If the red en green light is blinking. And I leave it for a day or 2 will be the battery self balance again? I just bought a new accu and this is what I get.
I have a PAP 20 A3 2020-03 battery from which I made a 20,000mAh Power Bank that has no discharge protection and several times discharged to a critical level and did not charge. In the evening I left it in the charger and in the morning I see that it has been charged. I mean, it turned out to be a very successful battery.
th-cam.com/video/vRydMn5B3CM/w-d-xo.html
Такова разбалансиране на клетките се получава най често при зареждане на батерията при ниски температури под 0°C. Възможно е да стане и при претоварване на батерията, батериите 2Ah трябва да се товарят максимум 10-12A самите клетки издържат до 18A но загряват доста при този ток. Този метод не го знаех, аз премахвах балансиращата платка на батерията и зареждах клетките една по една и после отново запоявах балансиращата платка. Но този метод е по лесен би трябвало да стане и с обикновен регулируем токоизправител като му се зададе 21V в конкретния случай с тази батерия на парксайд. Следващия път като имам такъв проблем ще проверя и този метод. Благодаря за видеото.
Може да се заредят без да се разпои платката, но при разбалансирани клетки трябва да се заредят един по един. Когата им захраниш общо със 21V, пак няма да се балансират или трябва да се изчака много докато платката ги балансира. Най добрия вариант е зареждане със 4,2V и максимум 2-3A
There should be some kind of low voltage cut off device to protect the battery from this; such low voltage cut off can be either in the battery itself or in the device that is supplying the load to the battery.
Вчера ми дадоха батерия с такъв проблем и ги излекувах с регулируем токоизпрарител
Olá eu preciso de comprar duas baterias 18v 1500mah
pra parafusadeira parkside PABS18A1 e o valor das duas baterias e aonde eu compro um
How long i need to leave them together
I have one that been drain down from the grinder won't charge anymore any idea how to fix this I did try the loop from another battery but still don't want to charge
Can you help me with the problem of not charging the green and red light is blinking, knowing that all cells are balanced
Try charging with 21V power supply. This is how it should work, if it doesn't work then there is a problem in the BMS itself.
@@ErCanEverything where to buy spare parts? i need a bms for 8ah battery. cells are ok
I was also looking for them, but they are nowhere to be found🤷♂️
I have a battery that does take charge (the lights do not blink on the charger). However the battery drains after a few seconds, and some powerful tools will not even power on. It is a 4Ah of the newer model with cell balancing. I got a new one on warranty, but I got to keep the old one. Is there anything I can do with this?
Probably 2 of the cells are destroyed, measure their voltages separately and see if they have differences? or return it for claim
My 20V Pack from Parkside (old Gen.) only shines the orange light (in the middle of green and red) when I press the test button and also doesn't charge - Could you please tell me what could be wrong here? Best Regards Toms
👏👏👏
Teşekkür ederim🤝
BEWARE of using older parkside batteries on other tools, all 20v parkside tools have a bms and cell balancing, BUT it does not test or prevent over discharge, if you over discharge a parkside battery, the protection chip in the battery will lock out the battery forever! it will not send 'handshake' to charger to start charging. its a safety feature of the bms IC to protect us from fire, not to increase company profit..
also recharging the cells 1 by 1 will not unlock it I have spent hours doing this, I have tried many parkside boards etc as I built a full 50mph+ e-motorcycle from parkside cells so i have a lot of the boards
Hi,
what does it mean when the battery charger parkside lights up red?
It means it is charging and once it is charging it will lights up green
i have same battery but i dont have charger, i have another 21v charger.could you help me to use other charge to charge this battery
Problem solved but it's mean that cells in this battery are very different. At least that one with voltage under 3v. And future life of the battery won't be long.
If it happens again, then I will replace the low voltage cells🙂
@@ErCanEverything I know, from my experience that this is a 'chain reaction'. The cells, at least those from older batteries (although yours is not old, from 2020) are not really high-current and especially in 2ah sets they are damaged or, like this one - degraded.
strange, I was expecting that this electronic circuit inside battery (controler and balancer) should take a care that each cell is equally charged. Seems that it is not balancer but some sort battery life limitator 😂
it might be balancing but the battery hasn't been used for over 1 year and I used on 80Nm performance drill and the battery died in about 5 minutes. Apparently the cells have malfunctioned
@@ErCanEverything probably some cells have higher self leakage, but balancer should resolve this during 1st charging, not just report error.
@@zokonjazokonja if out of balance it will charge and balance, if out of balance a great amount then it considers that to be too dangerous. if a cell goes
@@lezbriddon
It make sense. But this problem could be also solved by reducing charging current (slow charge), best way would be to somehow tell charger to decrease charging current. But thos would require some higher level of communication between balancer and charger.
@@zokonjazokonja there's 2 way comms on the third pin between chip in battery and chip in charger so it could be done, but I think the chips are programmed by the mystery supplier, I have never found a real data sheet or what the comms data means, I can watch it on my oscilloscope and i can force changes into it by heating the battery thermister but have no idea what the packets mean. its not a lidl chip i know other companies use it too like anker
grazie mille posso salvare la mia batteria PKS anche solo con un altra o serve tutta quella attrezzatura? Il mio aspirapolvere Roomba con batteria nuova (80 euro :( ) è morto dopo che è rimasto senza caricare per 20 gg, posso recuperare? grazie
can I use 24 volt car charger to wake these batteries up
it's a bit risky because a 24V charger generates 28.8V. But if you make the current pass through some kind of load resistor or some kind of lamp and monitor the voltage to the battery, it shouldn't exceed 21.6V
@@ErCanEverything what about if I post them over to you with payment in advance
Aynı sorun bendede oldu
Bozuk bataryayı iki adet araba bataryası (72 Ah*2) 600 watts bir invertöre normal şarj aleti ile bağlayarak şarj ettim ve sorunu hallettim nasıl neden düzeldi anlayamadım !
Batarya artık bu yöntem ile 10 dakikada ful doluyor 😃👌
Buy a balancing charger to hobbyking. Non need tension, full auto
działa :) props
hello i have same problem. but im in willage and i dont have second cordless drill or etc. and i dont have tool you have so is there any other way to solve this problem. like charge it with 220 to 12v adaptor or somthing like this. i have only two batteries car battery and tv remote 😂😂😂
Ask from a friend.
Hi, my PAPS 204 A1 wont fully charge, it goes to max 90% and stops, it's a new battery I didn't use it, voltage is 20.1, what can it be...