In the slicer there are setting that you can tweak, plus community made filliment changes g-codes that makes it least wasteful and faster. Also the purge block can 60% smaller and it works fine
Bambu filament rolls have an rfid tag on them that tells the printer what color and material they are when loaded in an ams/ams lite. Also it's not a purge block, it's a prime tower, it's priming the nozzle with the color it's getting ready to print.
Great timing on dropping A1 review, when recommend by Bambu to not be used. Gotta give them a big thumbs up though for their honesty 👍 #transparency #honesty #A1review
Great review and demo. I bought an a1 mini since the a1 is on recall, but I didn't buy the a1 mini combo, just the machine itself. I love it. As soon as the full size a1 comes back in stock after the recall I'm grabbing one, probably with the ams lite.
1:02:50 Bro you skipped the most interesting option in BambuStudio: The Flush options. We'd like to see how much purge/filament can be saved when printing flush into infill or supports.
After playing with it i'd say it cuts it down almost in half. I only say this cuz I had half the amount of rings made from recycling the waste after setting it up with bambu and community settings.
Mate I've watched alot of printer reviews and ur reviews and camera work are probably the best I've seen. We'll done. No one else focuses on the actual product itself the way u do. Thier all too interested in being in front of the camera which detracts from the product. Anyway keep up the great work
This is by far the best printer you can get for under $600 bar none. Bambu has set a high bar to other manufacturers and expect they are working overtime to compete.
@@leosiwicki2013 Indeed, and as a bonus you also get the top notch quality cables which will melt and sparkle free of charge and not at last an email to stop using it for the next 3-4 ish months until they fix this magnificent house burner
Bought last month and got with an extra Bed heater that fixes the problem. Often it is wise to buy a couple of months after launch so any issues are fixed.
Thanks for this video. The best demonstration I've seen out of a dozen or so I've watched. You took a lot of time to create this and you covered everything, it seems. Bravo, sir.
There were two brackets with FOUR screws holding the printer head arm that the instructions DID NOT tell me to remove. It kept failing calibration and a clicking noise until i figured out to remove the brackets. (You didn't have them in yours)
GREAT video. I'm going to order this tonight and just watching lots of videos before I hit 'BUY'... Your video goes over a lot of detail and answers a lot of stupid questions I would have had like what hole to put the filament guide into - doesn't matter LOL Perfect answer. THUMBS UP!
One of the few subs I watch to the very end. Always thorough always helpful. I just bought the ams for my A1 and thanks to you I can set it up and poop :)Thank you
There's another advantage to the AMS.. Using up spools fully by having multiple of the same colours, so it uses up one and then simply continues printing with the next
@@bkkorner You can use any filament you want, the RFID is just for automatically setting up what's in the AMS. You can simply do this manually with everything else.
@@bkkorner in the menu you can select other filament and it works just fine, the fancy bambu rfid spools are a very nice option though, i've honestly just stuck with them. Im more focused on learning 3D modeling atm than messing with the printer so bambu's ecosystem is nice and simple.
When you do small parts with lots of color changes i was told print multi prints at once. like the Penguin print like 4 or 5 of them at once. fill your bed plate with it. your purge block should not get any bigger but you end up getting 5 or more prints. (I do not own a bambu yet, mine will be here today.) Was also thinking how do you turn the purge block into a model? i read you can do this but dont know how yet.
What woul you say the main differece is between this unit and the mini? I imaagine the price is very similar now a days, but love to know because I am considering getting one. What are the advantages of thi one over the Mini? Thanks
The A1 3D has been pulled from their website and not available.Bambu Lab has recalled these printers due to defective heatbed cable mentioned by other posters.
Great video thanks for sharing. New to 3D printing this was a big help. I have one question when changing filiament you unload it. I'm using a generic filiment and when I go in to filiment it highlights load and exit only unload is not highlighted. Any help will be greatly appreciated. I'm using AMS
Yeah, I don't understand why ppl keep printing with frequent power outage and no UPS backup. This is computerized equipment so an UPS is absolutely essential.
any chance it would be worth it for you to make a video like this about the anycubic kobra 2 neo? there is almost no info about it and as a beginner and my first printer it was a bit of a big learning curve.
Hello amazing video, when I started this process, it said auto bed leveling 15 mins, I did not see that on your video when I followed everything you did.
The only reason to get AMS for me, was to be able to have PVA supports for some parts, to avoid having to divide and glue them. However, if that turns out too slow, I'll still probably divide and glue...
There’s a recent recall on this printer. The bed cable can get damaged and cause a fire. They now recommend you don’t use this printer until they figure a solution out.
totally not true! there is a problem with bed cable for less that 2% of sold printers. They came up with the solution in matter of hours. They are sending cable strengthener to everyone who bought the printer free of charge, whoever dont want to wait for delivery, can print it yourself in less than 30mins. Its also worth to mention that it happens to users whos cable is bumping onto something....
They sent out an update today saying not to use the printers ("we kindly request that you cease using the A1 printer for now"). Some creators were also contacted directly to either remove videos or append comments saying that it is recommended that no one operate the A1 printer. Pretty definitive that they don't feel it is safe to operate until the problem is fully understood.
@@DebeliChris it totally is true. They stopped all advertising on the A1. There is an engineering flaw with the cable and bed connection. Without a cable clip the cable will eventually break. If only 2% of people were affected, as you claim, They wouldn't need everyone to add the cable clip. I give Bambu credit for their rapid response. Mistakes happen, and they are trying to fix it.
Great video just waiting to receive my A1 Combo printer I also have an Ender3v3se and Creality CR6se been 3d printing for 5 years no more manual levelling anymore out with the older printer in with the new....
Awesome! I'm here after I watched the "Jared Owen Animations" blender 3d modeler breakdown of the Bambu A1 on youtube. Cool to see the physical product now that I saw how it works lol
I noticed that when you printed there is no use of any type of glue and the bed. (my present printer, I have to apply glue to the bed. Is it not needed on this machine?
Try and drop your z-offset by like 0.3mm :) This helps the print squish into the bed better Also, glue is messy, we use hairspray and that has been working really well for us :)
I've seen a few reviewers complain that the little tabs near the rear corners aren't high enough and they've had an issue where the build plate ends up on one of them and causes the plate to be raised and hit by the tip.
Check that you have removed the 2 black plastic transport locks on either side of the vertical axis - there is no mention of these in my manual. Once removed I managed to calibrate it.
Hi! I would like to buy my first 3D printer and I saw your video about the Neptune 4 Pro too. After some experience which one do you prefer? I am looking for printing lightsabers, helmets and figures. Thank you!
In Florida heb je ook outlet malls en daar is het zeker een stuk goedkoper. Ik haal spijkerbroeken bij Walmart. 15,- voor een Wrangler broek. Zit mij prima. Ik heb het foodcourt ff gemist in de mall.
I want to get into the 3D printing should I wait for the new version of the a1 to come out or should I go for the p1p and why or should I just go with a different 3D printer thanks in advance
Unfortunately the timing of the release of this video is at the same time that they are now asking ALL A1s to not be used regardless of cable damage or not.
They should put it on a notification header on their landing page on their website. Some guys got older info from their blog saying you can still use the A1 if you don't have the power cord issue, some are getting a more recent one saying full stop using the A1 via email.
I did not expect it to be so loud, its my first printer. It was not crazy loud but yes, I would not go to bed with that. From the door out of my room I cannot hear it anymore, but I can from within the room haha. Thats cute..... Headphones and thats it haha.
Quick update, it was the Benchy haha. It was going at a very high speed. I just started printing my very first real model other than the preloaded one (raspberry pi 5 case) to test the printer and it is very very quiet, I had gotten scared already, but I am so happy now again. Ha!
By the review Just Vlad did here I noticed that yes generic filaments can be utilized however because the RFID Bambu Lab uses on their spools is not on the generic filament spools we may have to manually input the colors. I think this is going to have to be my next printer because I am truly emotional every time my current printer's 4 point tram adjusting knobs turn into the Knobs from hell and the slip of paper to tram the bed WTH... I need this printer. XD
Just a thought here... would it be possible to re-use the empty spool and re-loaded with a generic same color filament ??? Thanks for hearing me out. 🤔
Super helpful and incredibly detailed, answered so many questions I didn't even know I had. Thank you!
OMG THANK YOU! This seems to be the ONLY video out in TH-cam land that actually shows you how to use the external spool! HUGE THANK YOU!
In the slicer there are setting that you can tweak, plus community made filliment changes g-codes that makes it least wasteful and faster. Also the purge block can 60% smaller and it works fine
Bambu filament rolls have an rfid tag on them that tells the printer what color and material they are when loaded in an ams/ams lite. Also it's not a purge block, it's a prime tower, it's priming the nozzle with the color it's getting ready to print.
Great timing on dropping A1 review, when recommend by Bambu to not be used. Gotta give them a big thumbs up though for their honesty 👍 #transparency #honesty #A1review
Great review and demo. I bought an a1 mini since the a1 is on recall, but I didn't buy the a1 mini combo, just the machine itself. I love it. As soon as the full size a1 comes back in stock after the recall I'm grabbing one, probably with the ams lite.
Are the 4 filaments provided with the A1 combo package ??
@@milatoulouvier8509 nah, if I were you. I'd check the website. it has all the information for what comes with it.
@@milatoulouvier8509 filament is not provided I'm afraid
@@milatoulouvier8509 no unfortunately not
This is hands-down the BEST review I have ever seen of a 3d printer. Thanks dude....SUBSCRIBED!
This is the review everyone interested in the A1 combo must watch. Fantastic job. I ordered one at the conclusion. 👍👍👍👍😊
Thanks
1:02:50
Bro you skipped the most interesting option in BambuStudio:
The Flush options. We'd like to see how much purge/filament can be saved when printing flush into infill or supports.
After playing with it i'd say it cuts it down almost in half. I only say this cuz I had half the amount of rings made from recycling the waste after setting it up with bambu and community settings.
Mate I've watched alot of printer reviews and ur reviews and camera work are probably the best I've seen. We'll done. No one else focuses on the actual product itself the way u do. Thier all too interested in being in front of the camera which detracts from the product. Anyway keep up the great work
Show us how to do a re-boxing cause we may all have to send them back lol
I liked and literally saved this video for when I am sending it back 🤣
exactly lol
This is by far the best printer you can get for under $600 bar none. Bambu has set a high bar to other manufacturers and expect they are working overtime to compete.
@@leosiwicki2013 Indeed, and as a bonus you also get the top notch quality cables which will melt and sparkle free of charge and not at last an email to stop using it for the next 3-4 ish months until they fix this magnificent house burner
Bought last month and got with an extra Bed heater that fixes the problem. Often it is wise to buy a couple of months after launch so any issues are fixed.
You ever used the abet a8 that little cable is nothing compared to the a8 it will be fine
Most detailed unboxing ever.
22:17: Fun fact, the A1 Mini and A1 doesn't have speakers, the tone you heard was produced by the stepper motors.
33:33 no way that sound is made by stepper motors xD
@@maxzett Об это сказано в аннотации к товару.
Thanks for this video. The best demonstration I've seen out of a dozen or so I've watched. You took a lot of time to create this and you covered everything, it seems. Bravo, sir.
There were two brackets with FOUR screws holding the printer head arm that the instructions DID NOT tell me to remove. It kept failing calibration and a clicking noise until i figured out to remove the brackets. (You didn't have them in yours)
GREAT video. I'm going to order this tonight and just watching lots of videos before I hit 'BUY'... Your video goes over a lot of detail and answers a lot of stupid questions I would have had like what hole to put the filament guide into - doesn't matter LOL Perfect answer. THUMBS UP!
The best unbox about this machine, thanks!
5:20 each bambulab filament roll has a nfc chip that's how it knows what filament are you using and automaticly pulls it in
Hello from Romania ! love your vids!
VLAD and Romania! Hand in hand!
I’m really enjoying your videos, just purchased a P1P, your videos are really great and helpful.
fantastic vid. Just ordered one and this was very clear and concise.
Very helpful, my dad said I could get one if I find one. I think I found it❤Thanks you
Thank you for providing beautiful content, I wish you one million subscribers within the next 3 months
Thank you so much ! We are new to 3D printing and this device was a tip from a friend and with you're video we can make a decision to buy it.
One of the few subs I watch to the very end. Always thorough always helpful. I just bought the ams for my A1 and thanks to you I can set it up and poop :)Thank you
That's a very impressive package. I'm relieved that it comes with a very nice little tool kit. I'll probably order mine today.
There's another advantage to the AMS..
Using up spools fully by having multiple of the same colours, so it uses up one and then simply continues printing with the next
The AMS knows what colour the filaments are because each Bambu filament roll has an RFID tag in it and the AMS reads it and sends it to the printer.
OMG does that mean we can't use any filament except Bambu's?
@@bkkorner You can use any filament you want, the RFID is just for automatically setting up what's in the AMS. You can simply do this manually with everything else.
@@bkkorner in the menu you can select other filament and it works just fine, the fancy bambu rfid spools are a very nice option though, i've honestly just stuck with them. Im more focused on learning 3D modeling atm than messing with the printer so bambu's ecosystem is nice and simple.
A power outage system could also prevent electronic damage to your A1. Loved all your demo and review.
Fantastic video. Very helpful. Thanks.
You're lucky. I didn't receive grease with my order. I ordered the same kit, you did plus six Filament reels. Sorry, I got the mini version of it
I am from Saudi Arabia. I enjoyed your coverage and intend to purchase the printer.
When you do small parts with lots of color changes i was told print multi prints at once. like the Penguin print like 4 or 5 of them at once. fill your bed plate with it. your purge block should not get any bigger but you end up getting 5 or more prints. (I do not own a bambu yet, mine will be here today.) Was also thinking how do you turn the purge block into a model? i read you can do this but dont know how yet.
What woul you say the main differece is between this unit and the mini? I imaagine the price is very similar now a days, but love to know because I am considering getting one. What are the advantages of thi one over the Mini? Thanks
The A1 3D has been pulled from their website and not available.Bambu Lab has recalled these printers due to defective heatbed cable mentioned by other posters.
Are the 4 filaments provided with the A1 combo package ??
@@milatoulouvier8509 I am curious also about this :D
Good video, but bad timing. Bambu has asked for everyone to turn them off until they come up with a solution to the cable problem
YEP cant even buy one right now
i bought one yesterday is it fixed?
@@xpectra4177 It may be - there is information to check the serial number, any after a certain date of manufacture are ok
could the filament stand be put on the other side which would allow a little more distance from the printer?
Great video thanks for sharing. New to 3D printing this was a big help. I have one question when changing filiament you unload it. I'm using a generic filiment and when I go in to filiment it highlights load and exit only unload is not highlighted. Any help will be greatly appreciated. I'm using AMS
if you have many power outages, I would suggest an UPS. my printers are all connected to UPS...
Yeah, I don't understand why ppl keep printing with frequent power outage and no UPS backup. This is computerized equipment so an UPS is absolutely essential.
@@DanangAlta we should send him an ups...
any chance it would be worth it for you to make a video like this about the anycubic kobra 2 neo? there is almost no info about it and as a beginner and my first printer it was a bit of a big learning curve.
Hello amazing video, when I started this process, it said auto bed leveling 15 mins, I did not see that on your video when I followed everything you did.
So, towers are necessary for multicolour? Isn't the flush already enough for no colour bleed? Thanks!!
The only reason to get AMS for me, was to be able to have PVA supports for some parts, to avoid having to divide and glue them. However, if that turns out too slow, I'll still probably divide and glue...
First Class video five stars to you.
There’s a recent recall on this printer. The bed cable can get damaged and cause a fire. They now recommend you don’t use this printer until they figure a solution out.
No, they stated IF ITS DAMAGED, stop using it. If it's not damaged, print out the extension bit and you're good to go.
totally not true! there is a problem with bed cable for less that 2% of sold printers. They came up with the solution in matter of hours. They are sending cable strengthener to everyone who bought the printer free of charge, whoever dont want to wait for delivery, can print it yourself in less than 30mins. Its also worth to mention that it happens to users whos cable is bumping onto something....
They sent out an update today saying not to use the printers ("we kindly request that you cease using the A1 printer for now"). Some creators were also contacted directly to either remove videos or append comments saying that it is recommended that no one operate the A1 printer. Pretty definitive that they don't feel it is safe to operate until the problem is fully understood.
@@DebeliChris it totally is true. They stopped all advertising on the A1. There is an engineering flaw with the cable and bed connection. Without a cable clip the cable will eventually break. If only 2% of people were affected, as you claim, They wouldn't need everyone to add the cable clip. I give Bambu credit for their rapid response. Mistakes happen, and they are trying to fix it.
@@deadlyapollo Its a full cease of use message now
fore the noking of i wud recomend using majigo for the buld plate i use it
Great video!
This may be a silly question but does the combo come with empty spools or do I need to order those as well?
Great video and man do I love this printer. Maybe I will still keep my Artillery X1 because it does larger prints.
great video, vlad. you need a ups for your power outages.
Great video just waiting to receive my A1 Combo printer I also have an Ender3v3se and Creality CR6se been 3d printing for 5 years no more manual levelling anymore out with the older printer in with the new....
Very informative. Thank you!
BRO THE FILM IS ON FIRE 20:01
Awesome! I'm here after I watched the "Jared Owen Animations" blender 3d modeler breakdown of the Bambu A1 on youtube. Cool to see the physical product now that I saw how it works lol
do you have to purge or can u let one colour blend in to the next ?
Thanks. Well explained.
I noticed that when you printed there is no use of any type of glue and the bed. (my present printer, I have to apply glue to the bed. Is it not needed on this machine?
Try and drop your z-offset by like 0.3mm :)
This helps the print squish into the bed better
Also, glue is messy, we use hairspray and that has been working really well for us :)
I've seen a few reviewers complain that the little tabs near the rear corners aren't high enough and they've had an issue where the build plate ends up on one of them and causes the plate to be raised and hit by the tip.
Great video..... How did the poop get on the plate when you were printing the turtle?
I would like to ask if I can only print with brands that have a 3D printer in the system or can I also print with other brands?
Great video, I just picked mine up, set it up, "Calibration fail" and it wont do anything else
Check that you have removed the 2 black plastic transport locks on either side of the vertical axis - there is no mention of these in my manual. Once removed I managed to calibrate it.
The Printer dosen't accualy havr a speaker! The sound is played by the motors and it's cool
Thanks for making this. This is by far the best one
Do you need a Bambu Account to use the Printer with Bambu Studio? I only want to use the printer on my local network.
What are the dimensions of the printer A1 with ams length and width in centimeters
Hi! I would like to buy my first 3D printer and I saw your video about the Neptune 4 Pro too. After some experience which one do you prefer? I am looking for printing lightsabers, helmets and figures. Thank you!
16:35. Good grief this is really good design work. Very clever stuff! Laurie. NZ. 😊
Can you please let me know what website you use to upload mode 3D models and how to import them into the SD card?
makerworld
In Florida heb je ook outlet malls en daar is het zeker een stuk goedkoper. Ik haal spijkerbroeken bij Walmart. 15,- voor een Wrangler broek. Zit mij prima.
Ik heb het foodcourt ff gemist in de mall.
How do you remove the single printing tube? It hard to remove
22:15 Fun fact: The melody the printer is playing is coming from the stepper motors 😊
What I did was put the cables into the ams facing forward so they bend forward
hello, did you pay for the filament swatches or did it come with the printer? I am looking to get one and would like to have it. Thanks.
I want to get into the 3D printing should I wait for the new version of the a1 to come out or should I go for the p1p and why or should I just go with a different 3D printer thanks in advance
Are the 4 filaments provided with the A1 combo package ??
@@milatoulouvier8509nope
What websites are you using to find these model
Is it possible to create a drawing for a JT file with sections etc.?
The filament reel has a barcode and the machine reads it andd tells the Lab A1 the color
Unfortunately the timing of the release of this video is at the same time that they are now asking ALL A1s to not be used regardless of cable damage or not.
They should put it on a notification header on their landing page on their website. Some guys got older info from their blog saying you can still use the A1 if you don't have the power cord issue, some are getting a more recent one saying full stop using the A1 via email.
My cover wont slide out ive poped it up but it wont slide out the y axis one
Wouldnt it be better quality with setting the speed to 85 % ?
Great video
Time to buy a UPS for your printer. Power failure failures seem to be an issue.
2:30 Before Buying Note that only some of the printers come with the hardware kit
During deals they will add "with free gift" and I'm pretty sure they just choose any one of the model supplement kits
Are the 4 filaments provided with the A1 combo package ??
ofc not. Only 50g for free (test)
Wow what a great video!! Helps me a lot 😃
I've a question, where did you find the bear? And what color did you used? Its really beautiful 😍
Wouldn’t use PET (or PLA) on brake calipers, they get way too hot!
how do u use non bambu lab filament with the ams
Can you do a video on the Prusa MK4S
Excellent video and very good explanation.
I did not expect it to be so loud, its my first printer. It was not crazy loud but yes, I would not go to bed with that. From the door out of my room I cannot hear it anymore, but I can from within the room haha. Thats cute..... Headphones and thats it haha.
Quick update, it was the Benchy haha. It was going at a very high speed. I just started printing my very first real model other than the preloaded one (raspberry pi 5 case) to test the printer and it is very very quiet, I had gotten scared already, but I am so happy now again. Ha!
Please do the A1 mini I need a review like yours (yours are the best)
You are incredible 🎉
hey vlad great video, used this to build my A1!
Does it work with generic filament sold by Amazon.?
By the review Just Vlad did here I noticed that yes generic filaments can be utilized however because the RFID Bambu Lab uses on their spools is not on the generic filament spools we may have to manually input the colors. I think this is going to have to be my next printer because I am truly emotional every time my current printer's 4 point tram adjusting knobs turn into the Knobs from hell and the slip of paper to tram the bed WTH... I need this printer. XD
Very nice! good job!
VLAD IS THE 🐐 OF 3D Printing
amazing review. thank you for that
Thanks for the good Video 👍🏻
the RFID chip on each spool tells the printer the colors. Work ONLY with BAMBU LABS spools
Just a thought here... would it be possible to re-use the empty spool and re-loaded with a generic same color filament ??? Thanks for hearing me out. 🤔