Please when using all these compressed gas cylinders always install the safety devices,that is the flash back arrestors on both the regulators and the torch end,this is very very important .
Thanks! Very true. I also learned that it's a good idea to get bigger tanks when you go to refill. The tanks do not get filled all the way and quit working before they are completely empty. When the acetylene gets low you can have flash back so don't run it when the acetylene gets low.
I can see that you can't weld to save your life. But hey at least you are trying. First of all for welding you are using a cutting torch. Use the welding tips for that 1/4" a number 4 tip is good. Heat up the welding surface until it gets red hot just enough to melt the surface then you introduced the welding rod. I set my welding tanks to 40 psi. for the oxygen and 10 psi. for the acetylene. That's just for welding. Keep burning my friend.
Thanks! I am terrible at welding. I need to take some classes. That may not even work. I may need a master like Mr. Miyagi from Karate Kid only if he were a welding master. Thanks for the tips. I need any I can get right now.
At first I skimmed the comments looking for an answer I thought this was a bit harsh. Then I watched the video and oof, point taken. Thanks For the video anyway ray. I think it showed me I should probably just buy the torch kit and get some bigger bottles.
Hello, how long does your gas and oxygen last? How many cuts can u make per set of tanks? Also is there a limit on how long you can use it before having to give it a “break” because of the acetone?
I have run my Port a Torch for an hour so far but am almost out of Acetylene. I still have a lot of Oxygen. Honestly, I have no regrets. I used to dread the idea of cutting with Oxy-Acetylene torches because the tanks were too big and heavy to lug around. Now it's fun because I can get to remote areas in my yard and cut stuff I would have never cut with the big tanks. I am actually thinking it's better to have 2 of each small tanks rather than one big Oxygen and one big Acetylene tank. I wont cut indoors because I don't want ash all over my garage. With that said, if you run the torch all day in a specially ventilated garage I would go with big tanks but I would still buy the Port a Torch because I love the Harris tips. I'd just switch my small tanks for bigger ones if volume becomes an issue. It cuts through metal really fast though so I don't feel the need for bigger tanks yet. Thanks for the comment!
Ray Stein hey thanks for replying. Was just wondering because of the 1/7th rule. That u can only use 1/7th of the tanks capacity per hour before having to give it a break. Just wondering how u dealt with that
@@JoseGarcia-sy3ss I take turns using my Dewalt Reciprocating saw, my Dewalt grinder and my Port a Torch. I save the torch for the cuts the other two can't handle. I do demolition so I always have something else to cut or break apart while the tank rests. I use the tool for short periods of time. I must admit though I have violated the 1/7th rule when I'm heating something up before bending. I just pay close attention to my flow and turn it off if I notice my flow rate decrease. With that said, safety is the most important thing when welding. I'm so glad you brought that up. I'll ask the guys at the gas store the next time I'm there and post their advice. I have a feeling they are going to tell me to use bigger tanks! Thanks for the comment because you may have saved a few of us on that one.
@@lhzav I've been told it's best to get larger tanks. They will exchange them no questions asked. I told them I wanted potability so they said I should consider medium sized tanks or a cart for larger tanks. I'm getting a cart and will see what sizes are actually available versus how much weight I'm willing to cart around.
Great question with a complicated answer. The numbers on the side tell when they were made and tested. When you go to refill them the gas companies read the numbers. If there are any issues they make you exchange the tanks or buy new ones but they last a long time. (Between 5-10 years on average)
Congratulations! I just bought this kit and I got the bottles refilled. My question is how long do the bottle contents last? I started using the torch today and I tested my cutting attachment which was maximum 5 mins and I did some welding which was around 15 mins total. now my Acetylene was at 200 psi and now it's less than 100, What's going on? How long do the tanks last when you use them?
The small tanks do not last long enough in my opinion. This is because a small amount of unused gas must be maintained. My tanks lasted about the same time that you mentioned. I am getting bigger tanks on my next refill. The only problem is the bigger the tanks the harder it gets to move so I'm looking into getting a torch cart.
@@RayStein Glad this exchange took place... I think I'm gonna use my small tanks to actually make a tank cart so when I do go and swap out for larger tanks I'll already have the cart...lol. Thanks guys.
Great video, i am torn between this kit or the miller tag a long TL550 they look similar i do know that. Im not familiar with who rebrands etc if anyone knows any infornation like that i would love to hear your opinion on this kit vs the miller mentioned above. Im most going to be using it for a heat/cutting source for automotive type applications i dont see myself using it for welding too much. Really enjoyed the video :)
I use it for exactly what you are. The two kits are almost exactly the same. You could go with either one and be fine. Lowes sells the Lincoln Electric so you can see it / return it if you have any problems.
I'm going to get bigger tanks for mine and use the hardware that came with it. That hardware is as good as any expensive model. I guess the price of oxygen and acetylene depends on various factors. Some places charge more than others where I live. (Pittsburgh)
@@lucasellyson6872 Thanks. To fill them. The small tanks lasted about 2 hours of off and on cutting. I got the opportunity to exchange them in for large tanks. Cost was $120 for the large tanks but they are well over twice the amount of fuel.
@@RayStein Your video inspired me to get one myself. They are very nice, now I have a big one for the shop n' a small one to pack around. Also, hehe, I'm no gas welder either. But always room to learn! :)
Just bought this set today for brazing. Thank you so much for posting this review
Thanks so much!
Great video, just bought this and thanks for the strap recommendation too!
Thanks!
Please when using all these compressed gas cylinders always install the safety devices,that is the flash back arrestors on both the regulators and the torch end,this is very very important .
Thanks! Very true. I also learned that it's a good idea to get bigger tanks when you go to refill. The tanks do not get filled all the way and quit working before they are completely empty. When the acetylene gets low you can have flash back so don't run it when the acetylene gets low.
I can see that you can't weld to save your life. But hey at least you are trying. First of all for welding you are using a cutting torch. Use the welding tips for that 1/4" a number 4 tip is good. Heat up the welding surface until it gets red hot just enough to melt the surface then you introduced the welding rod. I set my welding tanks to 40 psi. for the oxygen and 10 psi. for the acetylene. That's just for welding. Keep burning my friend.
Thanks! I am terrible at welding. I need to take some classes. That may not even work. I may need a master like Mr. Miyagi from Karate Kid only if he were a welding master. Thanks for the tips. I need any I can get right now.
At first I skimmed the comments looking for an answer I thought this was a bit harsh. Then I watched the video and oof, point taken. Thanks For the video anyway ray. I think it showed me I should probably just buy the torch kit and get some bigger bottles.
Thanks for the video and explanation, man! How many cuts can you get from one fill? I have a 2 7/8s pipe cutting project. Need to cut about 12times.
The torch gas does not last very long but it will do 12 cuts for sure.
Great review dude
Very true. Thanks!
detailed explanation of the torch
Thanks! I was hoping to help people who need repair parts for the torch.
Hello, how long does your gas and oxygen last? How many cuts can u make per set of tanks? Also is there a limit on how long you can use it before having to give it a “break” because of the acetone?
I have run my Port a Torch for an hour so far but am almost out of Acetylene. I still have a lot of Oxygen. Honestly, I have no regrets. I used to dread the idea of cutting with Oxy-Acetylene torches because the tanks were too big and heavy to lug around. Now it's fun because I can get to remote areas in my yard and cut stuff I would have never cut with the big tanks. I am actually thinking it's better to have 2 of each small tanks rather than one big Oxygen and one big Acetylene tank. I wont cut indoors because I don't want ash all over my garage. With that said, if you run the torch all day in a specially ventilated garage I would go with big tanks but I would still buy the Port a Torch because I love the Harris tips. I'd just switch my small tanks for bigger ones if volume becomes an issue. It cuts through metal really fast though so I don't feel the need for bigger tanks yet. Thanks for the comment!
Ray Stein hey thanks for replying. Was just wondering because of the 1/7th rule. That u can only use 1/7th of the tanks capacity per hour before having to give it a break. Just wondering how u dealt with that
@@JoseGarcia-sy3ss I take turns using my Dewalt Reciprocating saw, my Dewalt grinder and my Port a Torch. I save the torch for the cuts the other two can't handle. I do demolition so I always have something else to cut or break apart while the tank rests. I use the tool for short periods of time. I must admit though I have violated the 1/7th rule when I'm heating something up before bending. I just pay close attention to my flow and turn it off if I notice my flow rate decrease. With that said, safety is the most important thing when welding. I'm so glad you brought that up. I'll ask the guys at the gas store the next time I'm there and post their advice. I have a feeling they are going to tell me to use bigger tanks! Thanks for the comment because you may have saved a few of us on that one.
Ray Stein what did they say? Could you buy two more tanks and swap them out? One cools while you use the other?
@@lhzav I've been told it's best to get larger tanks. They will exchange them no questions asked. I told them I wanted potability so they said I should consider medium sized tanks or a cart for larger tanks. I'm getting a cart and will see what sizes are actually available versus how much weight I'm willing to cart around.
?did the tanks have all the serial markings and numbers, like that they can be refil ,plase let me know .Hector say hello from mississippi
The tanks have the numbers. They refilled them for me but I went to a welding store.
i just bought this kit from northern tool. i was a bit annoyed that hte tanks come empty
I agree. The tanks empty out pretty quick too. I'm getting bigger tanks the next time I fill up.
The refill is. $103 now in vegas
Thanks for the info.
Do these tanks have expiry dates?
Great question with a complicated answer. The numbers on the side tell when they were made and tested. When you go to refill them the gas companies read the numbers. If there are any issues they make you exchange the tanks or buy new ones but they last a long time. (Between 5-10 years on average)
Congratulations!
I just bought this kit and I got the bottles refilled.
My question is how long do the bottle contents last?
I started using the torch today and I tested my cutting attachment which was maximum 5 mins
and I did some welding which was around 15 mins total.
now my Acetylene was at 200 psi and now it's less than 100, What's going on?
How long do the tanks last when you use them?
The small tanks do not last long enough in my opinion. This is because a small amount of unused gas must be maintained. My tanks lasted about the same time that you mentioned. I am getting bigger tanks on my next refill. The only problem is the bigger the tanks the harder it gets to move so I'm looking into getting a torch cart.
@@RayStein Glad this exchange took place... I think I'm gonna use my small tanks to actually make a tank cart so when I do go and swap out for larger tanks I'll already have the cart...lol. Thanks guys.
@@EM-eh1pg
and use the 125 titanium welder to stick it together
Anybody else see Sid the sloth from the Ice Age movie when he shows the both the regulators on for the first time?
lol
Thank you
Thanks!
Try holding the tip closer to the metal your cutting maybe? Don't directly touch it to the metal tho
Thanks! I'll take any welding advice I can get. My metal never sticks for some reason.
Great video, i am torn between this kit or the miller tag a long TL550 they look similar i do know that. Im not familiar with who rebrands etc if anyone knows any infornation like that i would love to hear your opinion on this kit vs the miller mentioned above. Im most going to be using it for a heat/cutting source for automotive type applications i dont see myself using it for welding too much. Really enjoyed the video :)
I use it for exactly what you are. The two kits are almost exactly the same. You could go with either one and be fine. Lowes sells the Lincoln Electric so you can see it / return it if you have any problems.
@@RayStein thanks for the suggestion!
Could this be used for brazing for hvac stuf
Yes. It would work great for that. Just use the appropriate tip.
I just bought this kit and nothing comes out of the oxygen bottle Do you have to activate it?
They don't tell you on the box but the tanks have to be filled at your local gas welding store.
2:06 AIRPLANE!
Thanks!
This video was wonderful, thank you.
Thanks!
Wow this is a nice set, where did you purchase it from. Thanks for sharing
Lowes sells it. I will say I love the hardware but I recommend getting larger tanks on your first refill if possible.
Home Depot sells them too, it all depends tho, not every single store carries the same items as others
My small oxygen and acetylene tanks lasted 2 weeks. I had no problems with the gages. Also, they sell adapters if need be.
I know it is almost a year later but it cost me $73 for both tanks here in TX
I'm going to get bigger tanks for mine and use the hardware that came with it. That hardware is as good as any expensive model. I guess the price of oxygen and acetylene depends on various factors. Some places charge more than others where I live. (Pittsburgh)
You mean 73$ to fill them? Or to buy them
@@lucasellyson6872 Thanks. To fill them. The small tanks lasted about 2 hours of off and on cutting. I got the opportunity to exchange them in for large tanks. Cost was $120 for the large tanks but they are well over twice the amount of fuel.
You're awesome
Thanks!
Gas welding has very little UV and is not anywhere near MMA or the others.
Thanks!
Never use the cutting torch for brazing. That's what the brazing setup is for..
Welding is one of those things where it's important to learn in person from a skilled instructor. I'm hoping to take a class one day.
Your technique (or the lack there of) hurts me greatly... But at least you're trying.
L.O.L. I am so bad at welding. My welds are about as strong as cheap glue but the torch does cut quite well.
@@RayStein Your video inspired me to get one myself. They are very nice, now I have a big one for the shop n' a small one to pack around.
Also, hehe, I'm no gas welder either. But always room to learn! :)
thank you
You're welcome! Thanks!