PROFESSIONAL LEVEL Explanation. Straightforward. You're right on the money. No Fake News, No BS. The information is like a finely aged whisky that smoothly goes right in. The whole video is priceless. Salute
Npakalinaw lahat ng explanation mo d2 Sir. Hindi lhat ng Electl Engr alam ang ineexplain mo. Ang swerte ng mga electrician na ma eeducate sa mga vlog m Sir. The best Practical Electricity vlog n napanood ko with a very nice attitude. Salute.
Madaming nag kalitihan Dyan kahit engineer na iba d Alam Yan master electrician pinagtatalunan Dyan kung Anu ba Ang Tama Sabi nmn Ng iba hiwalay dapat may project aq Ngayon balak ko e bonding Ang problema baka mag baliktad Ang lagay Ng lineman Ng coop imbis sa l one sa ground nalagay kung Tama nmn panu kung may bagyo tas Basta Basta nila kinakabit tapus bumaliktad
Sir gud evening...iilan palang ang na watch ko na tuturial mo peroalam ko marami akong matututunan sa iyo...d2 sa amin ang connection is line to ground...pero walang gumawa ng bonding ng grounded conductor sa ground.
Buti pa to libre nood madaming matutunan . Pero nung nag aral ako kulang namn sa turo sabihin pa magresearch kayo . . Langya. Kaya nakasubscribe na ako sir at no skip ads pambawi man lang. Salamat sa mga videos mo Sir malaking tulong po
Subject was explained very well. great job of sharing or imparting of knowledge,skills and attitude. I can say very professional ang mode of delivery. This really a sound transformation of knowledge and i am pretty sure it contributes a lot to Filipino .
Tama po ang vlog nyo. Sa first siurce of disconnect lang ang main bonding para maiwasan ang grounding parallel path tsaka maiwasan ang objectionable current. Master elwctrician po ako sa state ng Florida usa.
Napaka detalyado ang paliwanag...sugest ko lang sir, na gamitin mo ang ibang term sa sinasabi mong voltage drop para hindi malilito ang mga batang electrical practitioners kung ano ang VD
hindi ako electrecian pero yung green na earth for safety. zero volt the same sa neutral zero volt. yung ibang equipnent paghinawakan mo may narandaman kang static kaya importanti yung earth para hindi ka ma static. yan lng alam ko.this vedio is very helpful.
Additional Info: 1.) Pwede ring wala na yung enclosed circuit breaker (ECB) ahead ng panelboard. Ang panelboard ay pwedeng magserve as service equipment basta meron tayong main bonding jumper between grounded conductor at equipment grounding conductor... Para sa mga lateral from concrete pedestal to building, check our post sa FB page below: facebook.com/eesnip/photos/a.104784707948425/268680188225542/ 2.) Kung gagamit ng RCCB or RCBO, make sure mauna ang main bonding jumper bago dumaan sa kanila. 3,) Kung di ibinigay ni Coop or DU ang grounded conductor: Option 1 is Make sure verify niyo po sa coop niyo if yung isang lang is grounded conductor or not. Pero marami rin ako nabalitaan din sa aking mga kakilala na may mga coop or DU na di nagbibigay ng grounded conductor. So far magiging violation po sir coop / du sa PEC dahil lrequired po silang ibigay sa inyo ang grounded conductor regardless kung magagamit po sa loads or hindi dahil yun lang ground fault return path naten ahead ng bonding jumper para mapatrip ang breaker. Pag ganun sir ang kaso, Option 2, install an RCCB / RCBO or GFCI (recommended ko sir is "MAXIMUM 100mA" Type A RCBO). Magiging TT earthing system sa IEC na po kasi ang system niyo, meaning, yung mga equipment enclosures at equipment grounding conductor naten ay yung earth ay gagamitin lang return path pabalik sa source. (Terre-Terre French word for grounded). sa ganitong case sir, hindi mapapatrip ang mga normal na breakers like MCB / MCCB kaya need na installation ng residual current devices para mabasa ng system ang ground leakage current. Sa next videos sir icocover ko din about dito sa mga magiging options kung sakaling walang ibigay si coop / du na grounded conductor para makatulong na din sa iba at tamang pagsizing ng RCD. Hindi na kasi ito saklaw ng PEC / NEC. IEC standards na kasi iaapply naten sa mga ganitong cases.
@@bloomberg4865 hi sir, mayron po tayong mga kasamahan na hindi pa po alam na yung bare messenger wire ay siyang grounded conductor. Not necessarily po na hindi po binibigay ni du or coop po. Thanks!
Sir kng di binigay ni du ang grounded conductor then maglalagay tau ako ng rcbo, kailangan pa bang ung grounded conductor pagdating sa service equipment ay need pang iconnect pa puntang grounding rod or TT earthing nlng kc may rcbo nman?.
Good morning sir … I’m high voltage electrician/ lineman and I started my job in rural electrician in the province sometime 60 years ago, now I’m still working the same job dealing with substation, underground transmission/ distribution & overhead lines.. thank very much for showing this information to your channel, you can save the life those curious people doing the wrong job… God bless & good day
Master magandang araw sayo maraming salamat napakahusay mong mag explain tungkol sa grounding connection sa.line to ground system connection sana hindi ka magsawang gumawa na mga vedeo tungkol sa electrical na naka base pec palagi akong mag aabang sa mga darating pang mga vedeo master mabuhay ka.master god bless you always.
this is very informative. the most professional approach I've watched so fsr here on youtube. im an undergraduate in EE and from time-to-time i watch videos like this since im also a practicing electrician myself. i always advice electricians to religiously follow PEC standard whenever they are engaged in electrical installations because honestly, i encountered a lot of electricians who doesn't care about PEC standards. i will recommend this channel for them to learn the proper practice.
0:00 - Intro 1:27 - Basic Connection 3:38 - Neutral at Ground Main Bonding Jumper 5:03 - Bawal ang Bonding sa Loadside 7:54 - Grounding Rod Location 9:12 - Service Equipment Grounding 9:37 - Meter Base Grounding 10:43 - Grounding Busbar 11:54 - 1 Pole Circuit Breaker 12:58 - 2 Pole Circuit Breaker 13:56 - 1 Pole Fuse at Safety Switch 15:56 - 2 Pole Fuse at Safety Switch 17:24 - 2 Pole Fuse VIOLATION 18:01 - 110V Volts sa Line to Ground??? 18:53 - Service Entrance Details 19:35 - Meter Base Wiring Form 1S 21:42 - Service Equipment and Feeder Details 22:40 - Service Entrance Full Details 22:49 - Utility Transformer and Distribution Details 23:35 - TVSS or Surge Protective Device Requirement 25:09 - Transformer General Wiring Details 26:04 - VIOLATION: Color Coding 27:31 - VIOLATION: Online Blog 28:05 - VIOLATION: Walang Ground Wire 29:36 - VIOLATION: Walang Bonding 32:21 - VIOLATION: 2 Pole Fuse 33:03 - VIOLATION: Nasa Grounded Wire ang Switch 33:44 - VIOLATION: Ginawang Return ang Ground
Sana gumawa kp sir ng iba pang video at e-post d2 sa YT. Marami kang natutulungang mga LEP, maging yung mga skilled non-LEP. Huwag magpa impluwensya sa mga taong gustong pagkakitaan yung talent mo sir. More power and more videos sir.
for me though it's an additional expense. 3 wire is better than 2 wire. since there's is only 110 per line in 3 wire with respect to the neutral, while the 2 wire system is 220 agad ang isang linya which is more fatal when you accidentally touch the live wire. So safety wise mas maigi na ang 3 wire o line to line kaysa 2 wire or line to ground. You can't buy safety, sabi nila. Dapat ang mga videong ganito ang pinapanood imbis na tiktok. maraming diyers a pinoy na alam nila paano mag electrical wiring (marunong sila sa How)pero kulang sa kaalaman pagdating sa theory which is very important para alam nila ang why? salamat po and continue sharing. btw ubos ang dalawang ads :)
Boss salmat sa iyung tutorials video may natutunan ako,,, atsa parang tama ang pagkaintindi samga dini discus mo khit hindi ako electirian nakaiitindihan ko, slmat boss may mga nattunan sau boss, tama marami sa youtube ,god bless you,, maaaring pa shout-out boss alex Berondo from general santos city
un 1ng pic, si philippine life. commoner lng din sya like many of us. ndi rin sya aware s mga standards especially mga foreign nat'ls cla. possible n un lng din cnabi s knila nun local n gumwa s bhy nila so nmisled lng din c philippine life blogger...
Thank you po Sir sa mga malinaw na paliwanag. After watching this full video , dito ko rin nalaman ang sagot sa aking tanong kung pwedng kumuha ng 110 V between line to ground (hindi pala pwede). Now, i am convinced na mali yong napanood kong video nong ibang tao.
Salamat po sir. Marami po akong natutunan. Request lang po sir, kung ok lang, kung paano naman po ang grounding sa mga barko. Salamat po ulit at God bless.
I salute you for hitting those cowboy electricians in you tube who’s trying to educate with little knowledge about our system without them knowing that it is a violation of the code and will result to death and damage to properties.
3:28 mark- correction po Master hindi yan kapareho ng TN-C-S instead is TT arrangement dahil ang na-provide ng Coop or Distribution going to your premise is only a Line & Earthed connection. It is now the responsibility of the consumer to provide for their own earth/ground connection thru earthing rod to distribute in its internal circuit of system for connection of exposed conductive part of any equipment. I do agree with you that a bonding is required as per PEC at the consumer side and that there will be a main earth/ground conductor that needs to be connected now to the earthing rod within your panelboard/consumer unit with earth/ground terminal blocks for each connection point like sockets /lighting making it 3 wires protruding so in case of Line to ground fault ay meron relief to the ground and it needs an RCD/RCCB/RCBO to clear that fault really and besides marami ang nakaka overlook nito na ang system impedance between Distributor earthing rod at consumer earthing rod ay mataas. So correction it’s not a TN-C-S(Terre Neutral Combined Separate)but a TT(Terre Terre). Isinama ko sa comment what the acronyms stands for the benefit of readers, which I know you know it no offense😁Thanks!
Hello sir the way you explain is you are expert and professional. May i ask po If its ok for not puting grounding at home. Dahil line to ground na po daw dito sa mindanao po? Pls. Clarify. Thank you!
Ayos na ayos yong explanation mo Sir, thank you for your time and effort, sharing your understanding/expertise on the subject matter, watching your videos clarified some of the questions and other practices that are questionable not only to me but for sure to some other practitioner as well, Keep on uploading/sharing your thoughts it helps a lot.
sir new subscriber here....doon sa part ng RCCB na sinabi mo yun ang ginamit kong installation ko sa bahay ko at satisfied naman ako kc effective talaga ang protection. pumipitik ang breaker ko very sensitive siya kaya kaya iwas sa sunog. at electroic shock...okay ung videos mo .thanks
Dito sa Batangas, specifically Batelec 1, napakadelikado ng kuryente. Isang hot wire na 440volts ang isang linya, then galing naman sa ground ang isa. Pag naliligo ka, nakatapak ka na bale sa isang linya. Isang line lang napadikit ka or nahulog sa yo, tapos ka.
Ang galing nyo po master idol salamat sa video ninyo kasi malaking tulong po ito sa kagaya Kong Isang electrician. naka subscribe at naka all bell napo ako sa channel nyo idol
IBANG KLASE BOSS HEHE PARANG NAG-AARAL NALANG DIN AKO SA TESDA NETO BOSS. SALAMAT AT NKITA KO RIN VIDEO MO. PANG-ADVANCE STUDY NARIN INCASE NA MAGAAPLY AKO SA TESDA THANK SO MUCH BOSS❤️❤️😊
Subrang thank you sir SA vlog mo napakalianw talaga . Dito po sa Amin sa probensia ay line to neutral tanong kolang po SA outlet ng Aircon sir kaylangan PABA maglagay Ng ground?salamat po and God bless you
Ganyan din po,ang sinusunod sa mga European countries na ang Main Disconnect CB Panelboard ay bonded ang Neutral wire sa ground wire or TNC.Downstream ay TNS na which is EARTHING and NEUTRAL are separate.
Hello sir maganda ang iyog presentation lalo kong pinag interesan ang imparting of technical knowledge sa style na gamit mo practical talga accompanied by PEC gus to kita sir parang pumapasok ako sa course of Electrical Engineer Sir do you also entertain some inquiries? Pls just count me as your online student,
Ang form 2s na metro po ay 3wire single phase at ang form 1s po ay 2 wire single phase, kaya sa form 2S po ay kailangan gamitin ang dalawang coil para completo po ang mtering circuit
Thanks Sir for the basic information and knowledge on electrical grounding system that benefits every electrical practitioners. Unfortunately, it is sad to mention that major points (per latest PEC) are not being observed and considered at all in building elect. installation in the province (in my area): 1. No equipment grounding conductors (EGC) or circuit protective conductor (CPC) installed. For single phase LN system, TNC is adapted even up to internal building installation which is dangerous in the event of fault or disconnected neutral. 2. For street lighting system, steel poles are without bonding to earth. Earthing connection is provided by utility at point of supply only. 3. Lightning protection system are not introduced for taller buildings. (above 3 floors) 4. As part of technical documentation in electrical design, I observed that in the short circuit calculation, the determination of minimum Isc levels are not included (only the max KAIC level is determined). Such are used to classify MCB types (B, C, D, Z) or to calibrate MCCB magnetic trip settings if adjustable and electronic types. 5. Other electrical standards such as method of installations and proper materials. I know that concerned authorities (LGU and Electric Coop) are approving and issuing electrical permits with the coordination of contractor/PEE. There is no proper implementation and work checked on the actual installation which are in violation of latest PEC provisions. This are my observations and comments as a retired OFW on the prevailing electrical practices here in my area and I hope that these malpractices can be corrected. RGG
Thank you po sa malinaw na explaination. Tanong ko lang po sir kung ok lang po ba ang BONDING JOINT sa loob na ng bahay pati ang gounding rod. Wala po kasi nakaabang na DISCONNECT MAIN sa labas....maraming salamat po
PROFESSIONAL LEVEL Explanation. Straightforward. You're right on the money. No Fake News, No BS. The information is like a finely aged whisky that smoothly goes right in. The whole video is priceless. Salute
thanks sir!
Npakalinaw lahat ng explanation mo d2 Sir. Hindi lhat ng Electl Engr alam ang ineexplain mo. Ang swerte ng mga electrician na ma eeducate sa mga vlog m Sir. The best Practical Electricity vlog n napanood ko with a very nice attitude. Salute.
Salamat sir tony more power 👍
Madaming nag kalitihan Dyan kahit engineer na iba d Alam Yan master electrician pinagtatalunan Dyan kung Anu ba Ang Tama Sabi nmn Ng iba hiwalay dapat may project aq Ngayon balak ko e bonding Ang problema baka mag baliktad Ang lagay Ng lineman Ng coop imbis sa l one sa ground nalagay kung Tama nmn panu kung may bagyo tas Basta Basta nila kinakabit tapus bumaliktad
Sir gud evening...iilan palang ang na watch ko na tuturial mo peroalam ko marami akong matututunan sa iyo...d2 sa amin ang connection is line to ground...pero walang gumawa ng bonding ng grounded conductor sa ground.
🔗PRACTICAL PHILIPPINE ELECTRICAL WEBINAR SERIES FULL PLAYLIST
th-cam.com/play/PLO4MWmSMQe6Z56GgD5IkGBzHMvW0u_Tqe.html
Buti pa to libre nood madaming matutunan . Pero nung nag aral ako kulang namn sa turo sabihin pa magresearch kayo . . Langya.
Kaya nakasubscribe na ako sir at no skip ads pambawi man lang. Salamat sa mga videos mo Sir malaking tulong po
Subject was explained very well. great job of sharing or imparting of knowledge,skills and attitude. I can say very professional ang mode of delivery. This really a sound transformation of knowledge and i am pretty sure it contributes a lot to Filipino .
yes sir. thanks very much!
Tama po ang vlog nyo. Sa first siurce of disconnect lang ang main bonding para maiwasan ang grounding parallel path tsaka maiwasan ang objectionable current. Master elwctrician po ako sa state ng Florida usa.
Subrang linaw ng paliwang mo idol,,. Salamat at marami kang naitamang mali, na akala ng iba ay tama.
Napaka detalyado ang paliwanag...sugest ko lang sir, na gamitin mo ang ibang term sa sinasabi mong voltage drop para hindi malilito ang mga batang electrical practitioners kung ano ang VD
LINE TO GROUND AT LINE TO LINE SERVICE ENTRANCE POLE LATERAL PART 1 EP 12
th-cam.com/video/vunNWKiXKPM/w-d-xo.html
hindi ako electrecian pero yung green na earth for safety. zero volt the same sa neutral zero volt. yung ibang equipnent paghinawakan mo may narandaman kang static kaya importanti yung earth para hindi ka ma static. yan lng alam ko.this vedio is very helpful.
Additional Info:
1.) Pwede ring wala na yung enclosed circuit breaker (ECB) ahead ng panelboard. Ang panelboard ay pwedeng magserve as service equipment basta meron tayong main bonding jumper between grounded conductor at equipment grounding conductor...
Para sa mga lateral from concrete pedestal to building, check our post sa FB page below:
facebook.com/eesnip/photos/a.104784707948425/268680188225542/
2.) Kung gagamit ng RCCB or RCBO, make sure mauna ang main bonding jumper bago dumaan sa kanila.
3,) Kung di ibinigay ni Coop or DU ang grounded conductor:
Option 1 is Make sure verify niyo po sa coop niyo if yung isang lang is grounded conductor or not.
Pero marami rin ako nabalitaan din sa aking mga kakilala na may mga coop or DU na di nagbibigay ng grounded conductor.
So far magiging violation po sir coop / du sa PEC dahil lrequired po silang ibigay sa inyo ang grounded conductor regardless kung magagamit po sa loads or hindi dahil yun lang ground fault return path naten ahead ng bonding jumper para mapatrip ang breaker.
Pag ganun sir ang kaso, Option 2, install an RCCB / RCBO or GFCI (recommended ko sir is "MAXIMUM 100mA" Type A RCBO). Magiging TT earthing system sa IEC na po kasi ang system niyo, meaning, yung mga equipment enclosures at equipment grounding conductor naten ay yung earth ay gagamitin lang return path pabalik sa source. (Terre-Terre French word for grounded). sa ganitong case sir, hindi mapapatrip ang mga normal na breakers like MCB / MCCB kaya need na installation ng residual current devices para mabasa ng system ang ground leakage current.
Sa next videos sir icocover ko din about dito sa mga magiging options kung sakaling walang ibigay si coop / du na grounded conductor para makatulong na din sa iba at tamang pagsizing ng RCD. Hindi na kasi ito saklaw ng PEC / NEC. IEC standards na kasi iaapply naten sa mga ganitong cases.
Ibig sbhn sir minsan bnbgy n d.u ung isang line lang? Wla na ung neutral?
@@bloomberg4865 hi sir, mayron po tayong mga kasamahan na hindi pa po alam na yung bare messenger wire ay siyang grounded conductor. Not necessarily po na hindi po binibigay ni du or coop po. Thanks!
@@practicalelectrical3837 ok sir gets . Salamat po sa mga videos nyo inaabangn naman napakaganda ng explination
@@bloomberg4865 no problem salamat 🙏
Sir kng di binigay ni du ang grounded conductor then maglalagay tau ako ng rcbo, kailangan pa bang ung grounded conductor pagdating sa service equipment ay need pang iconnect pa puntang grounding rod or TT earthing nlng kc may rcbo nman?.
Good morning sir … I’m high voltage electrician/ lineman and I started my job in rural electrician in the province sometime 60 years ago, now I’m still working the same job dealing with substation, underground transmission/ distribution & overhead lines.. thank very much for showing this information to your channel, you can save the life those curious people doing the wrong job… God bless & good day
Sir. Ang galing nyo po. Napakagaling mag expalin at proper presmat. Para lang bumalik sa school. +1 subscription. Thanks
Mabuti nalang may vlog na ganto na napakalinaw. Thankyou sir sa mga vlog nyo
Master magandang araw sayo maraming salamat napakahusay mong mag explain tungkol sa grounding connection sa.line to ground system connection sana hindi ka magsawang gumawa na mga vedeo tungkol sa electrical na naka base pec palagi akong mag aabang sa mga darating pang mga vedeo master mabuhay ka.master god bless you always.
Yes sir. Medyo matagal lang makapag release pero tuloy tuloy yan. 👍
Idol malinaw ung paliwanag mo .ang iba kc magpailaw lang electrician na ang dating.
hehe salamat sir oscar.
this is very informative. the most professional approach I've watched so fsr here on youtube. im an undergraduate in EE and from time-to-time i watch videos like this since im also a practicing electrician myself. i always advice electricians to religiously follow PEC standard whenever they are engaged in electrical installations because honestly, i encountered a lot of electricians who doesn't care about PEC standards. i will recommend this channel for them to learn the proper practice.
tnx master dami ko napanood sa youtube pero isa to sa mga napakainformative malinaw pagkaka explain
salamat sir. more to come po
0:00 - Intro
1:27 - Basic Connection
3:38 - Neutral at Ground Main Bonding Jumper
5:03 - Bawal ang Bonding sa Loadside
7:54 - Grounding Rod Location
9:12 - Service Equipment Grounding
9:37 - Meter Base Grounding
10:43 - Grounding Busbar
11:54 - 1 Pole Circuit Breaker
12:58 - 2 Pole Circuit Breaker
13:56 - 1 Pole Fuse at Safety Switch
15:56 - 2 Pole Fuse at Safety Switch
17:24 - 2 Pole Fuse VIOLATION
18:01 - 110V Volts sa Line to Ground???
18:53 - Service Entrance Details
19:35 - Meter Base Wiring Form 1S
21:42 - Service Equipment and Feeder Details
22:40 - Service Entrance Full Details
22:49 - Utility Transformer and Distribution Details
23:35 - TVSS or Surge Protective Device Requirement
25:09 - Transformer General Wiring Details
26:04 - VIOLATION: Color Coding
27:31 - VIOLATION: Online Blog
28:05 - VIOLATION: Walang Ground Wire
29:36 - VIOLATION: Walang Bonding
32:21 - VIOLATION: 2 Pole Fuse
33:03 - VIOLATION: Nasa Grounded Wire ang Switch
33:44 - VIOLATION: Ginawang Return ang Ground
Sana gumawa kp sir ng iba pang video at e-post d2 sa YT. Marami kang natutulungang mga LEP, maging yung mga skilled non-LEP. Huwag magpa impluwensya sa mga taong gustong pagkakitaan yung talent mo sir. More power and more videos sir.
Ang ganda, well explained lahat. Can't wait sa topic ng SPD, kasi halos lahat ng nakikita ko sa web TT and TNS connection.
Thanks sir ⚡
Laki ng tulong neto lalo sa katulad kong baguhan pa sa electrical installation🥰😍🥰😍
Gusto ko talaga matuto mag electrician. Very informative.
Mike Holt Jr of the Philippines.
Hi sir. Layo pa po niyan hehe 😂😂😂
Marame po ako natutunan sainyo master more video po sana wag kayu mag sawa
for me though it's an additional expense. 3 wire is better than 2 wire. since there's is only 110 per line in 3 wire with respect to the neutral, while the 2 wire system is 220 agad ang isang linya which is more fatal when you accidentally touch the live wire. So safety wise mas maigi na ang 3 wire o line to line kaysa 2 wire or line to ground. You can't buy safety, sabi nila. Dapat ang mga videong ganito ang pinapanood imbis na tiktok. maraming diyers a pinoy na alam nila paano mag electrical wiring (marunong sila sa How)pero kulang sa kaalaman pagdating sa theory which is very important para alam nila ang why? salamat po and continue sharing. btw ubos ang dalawang ads :)
Galing daminkung na tutunan.poh sa inio po kahit d po ako nag school. Inulit ulit kulang para maintindhan
Understandable kahit sa hindi mga electrician . tnx
Boss salmat sa iyung tutorials video may natutunan ako,,, atsa parang tama ang pagkaintindi samga dini discus mo khit hindi ako electirian nakaiitindihan ko, slmat boss may mga nattunan sau boss, tama marami sa youtube ,god bless you,, maaaring pa shout-out boss alex Berondo from general santos city
Nag enjoy po kami sir kahit mahaba..... Hehe.....
Yes sir. Salamat. Webinar po kasi 😂😂😂
Newbie ako gusto ko matuto nuod ako youtube dmi nd nag lalgay ng grounding.pero ito safety first....
Ang Ganda nang pg ka explain mu master ..na intindihan ko lahat .. maraming salamat ..more videos to Po master ..God Bless ..
Maraming salamat sa ganitong topic boss at Marami akung natutunan sayo. 👍👍👍👍👍👍👍
God bless.
very educational at base talaga sa PEC, thank you and keep it going sir great job!
Thank sir 👋
thank you very much sir sa info at knowledge na ni share mo,,tama ka napakaraming mali sa s inet at sa mga fb groups poser minsan,,,
Yes master. Sana nakatulong po. 👋
un 1ng pic, si philippine life. commoner lng din sya like many of us. ndi rin sya aware s mga standards especially mga foreign nat'ls cla. possible n un lng din cnabi s knila nun local n gumwa s bhy nila so nmisled lng din c philippine life blogger...
Napakagandang video. Super educational, clear graphic presentations and nice pa boses ng speaker.
Amdito lahar ng concern ko ,,nsagot pla dito maraming salamt master sa info😇nangamgarap din ako mging RME.soom😊
Very nice presentation,, clear na clear,, very helpful. Thank you very much for sharing.
Thanks. Hope you learned 😀
Salamat sa kaalaman maituro ko rin some points sa mga trainee ko sa TESDA...god bless...
Okay ba okay po iyon sir Jose. Salamat 👍
The best talaga to.hindi nakakasawa panuorin ang video nya.
Thank you po Sir sa mga malinaw na paliwanag. After watching this full video , dito ko rin nalaman ang sagot sa aking tanong kung pwedng kumuha ng 110 V between line to ground (hindi pala pwede). Now, i am convinced na mali yong napanood kong video nong ibang tao.
Ayos ang galing mo magpaliwanag master. More video pa master marami ka matutulungan
Magandang talakayan master... Sa tamang paglagay ng grounding system base sa PEC
Salamat po sir. Marami po akong natutunan. Request lang po sir, kung ok lang, kung paano naman po ang grounding sa mga barko. Salamat po ulit at God bless.
Very Informative ! andami ko natutunan. Salamat !
Thanks po sa tutorial, marami akong natututonan about electrical.
I salute you for hitting those cowboy electricians in you tube who’s trying to educate with little knowledge about our system without them knowing that it is a violation of the code and will result to death and damage to properties.
3:28 mark- correction po Master hindi yan kapareho ng TN-C-S instead is TT arrangement dahil ang na-provide ng Coop or Distribution going to your premise is only a Line & Earthed connection. It is now the responsibility of the consumer to provide for their own earth/ground connection thru earthing rod to distribute in its internal circuit of system for connection of exposed conductive part of any equipment. I do agree with you that a bonding is required as per PEC at the consumer side and that there will be a main earth/ground conductor that needs to be connected now to the earthing rod within your panelboard/consumer unit with earth/ground terminal blocks for each connection point like sockets /lighting making it 3 wires protruding so in case of Line to ground fault ay meron relief to the ground and it needs an RCD/RCCB/RCBO to clear that fault really and besides marami ang nakaka overlook nito na ang system impedance between Distributor earthing rod at consumer earthing rod ay mataas. So correction it’s not a TN-C-S(Terre Neutral Combined Separate)but a TT(Terre Terre). Isinama ko sa comment what the acronyms stands for the benefit of readers, which I know you know it no offense😁Thanks!
Hello sir the way you explain is you are expert and professional. May i ask po If its ok for not puting grounding at home. Dahil line to ground na po daw dito sa mindanao po? Pls. Clarify. Thank you!
Very helpful video sir! well presented. Thank you and God bless.
thanks sir! God bless too. hope you learned something.
Ayos na ayos yong explanation mo Sir, thank you for your time and effort, sharing your understanding/expertise on the subject matter, watching your videos clarified some of the questions and other practices that are questionable not only to me but for sure to some other practitioner as well, Keep on uploading/sharing your thoughts it helps a lot.
Saklap.. dahil dyan marami na akong nakagawian na iiwasan ko na
Thank you sir. Dame ko natutunan. From province palawan po ito.
nice sir,,ganda ng pag discuss mo,malinaw maiintindihan talaga sa marami
sir new subscriber here....doon sa part ng RCCB na sinabi mo yun ang ginamit kong installation ko sa bahay ko at satisfied naman ako kc effective talaga ang protection. pumipitik ang breaker ko very sensitive siya kaya kaya iwas sa sunog. at electroic shock...okay ung videos mo .thanks
Been watching videos on electrical connections. This gave the most convincing & legitimate explanation. Thanks more video please!
Salamat sa review line to ground
Thanks sir..nalaman ko ang kahalagan ng grounding..
Sir thank you po s mga binabhagi mo!!God bless po!!
Very informative and well explained Sir. Looking for more videos to come. Salute you Sir.Thanks
Salamat sir. Medyo busy lang haha pero more to come po.
Thank you sa content sir. More of this , MOre power
❤Watching Abu Dhabi UAE
Dito sa Batangas, specifically Batelec 1, napakadelikado ng kuryente. Isang hot wire na 440volts ang isang linya, then galing naman sa ground ang isa. Pag naliligo ka, nakatapak ka na bale sa isang linya. Isang line lang napadikit ka or nahulog sa yo, tapos ka.
super gandan pa ka turo mu sir salamat sa vedio maramin ako natutunan
Sir Khit mahaba yun video ok lng mi ntututunan nmn mga information.👍👍👍
Sir habang napapanood ko mga video mo pakiramdam ko mas magaling n ako s kinukuha naming electrician.hahaha
Hehe salamat sir 👍
At kapag ikaw na ang pumalit sakanya pakiramdam mo rin para kang nakukuryente dahil sa presure ng trabaho 🤣🤣
Very informative . Interesting topics. Thanks.
Thanks sir ⚡⚡⚡
Nice sir... Sarap manuod ng video mo sir. Waiting for the next episode. 😊
Thanks sir 👋
Thank you sir ngayun ko lang napanuod ang video mo at napakaganda at linaw ng paliwanag mo.. watching in qatar
Thank you dennis. Feel free to share 😀
Thank you. You deserve a subscribe. Panunuorin ko pa ang iba niyong mga video.
Ang galing nyo po master idol salamat sa video ninyo kasi malaking tulong po ito sa kagaya Kong Isang electrician. naka subscribe at naka all bell napo ako sa channel nyo idol
salamat sa info boss. very informative.
thanks sir
Dami q ntutunan syo boss, god bless
Thanks sir. 👋
Maraming salamat sir 👷♂️
Inspiring Rme po ako
thank you Sir waiting po s episode 5. sobrang linaw.
Salamat po. Yes sir. Next weekend sir. 👋
@@practicalelectrical3837
Sir may itatanong po sna ako
Regarding sa meterbase na GFTP 5JJAW
kung pwede po ba tlga xa pang 3 phase
Nice explanation sir.
IBANG KLASE BOSS HEHE PARANG NAG-AARAL NALANG DIN AKO SA TESDA NETO BOSS.
SALAMAT AT NKITA KO RIN VIDEO MO.
PANG-ADVANCE STUDY NARIN INCASE NA MAGAAPLY AKO SA TESDA
THANK SO MUCH BOSS❤️❤️😊
Subrang thank you sir SA vlog mo napakalianw talaga . Dito po sa Amin sa probensia ay line to neutral tanong kolang po SA outlet ng Aircon sir kaylangan PABA maglagay Ng ground?salamat po and God bless you
Salamat dito lods.. ang dami kong natutunan
ganda ng pagkaka-explained very detailed at maganda ang diagram. thank you sir!
Matrabaho nga lng sir gawin hehe. Salamat sir.
Salamat sa pag share sir god bless you
Ganyan din po,ang sinusunod sa mga European countries na ang Main Disconnect CB Panelboard ay bonded ang Neutral wire sa ground wire or TNC.Downstream ay TNS na which is EARTHING and NEUTRAL are separate.
Thanks sir sa info I've learned a lot
Napag aralan ko n yan sa book ni max pajardo hahaha!!
Worth to watch.
Hello sir maganda ang iyog presentation lalo kong pinag interesan ang imparting of technical knowledge sa style na gamit mo practical talga accompanied by PEC gus to kita sir parang pumapasok ako sa course of Electrical Engineer Sir do you also entertain some inquiries? Pls just count me as your online student,
Master magandanghapon marami akong nalaman ngayon, sana po matulungan nyo pa ako tungkol sa line to ground
ang linaw ng paliwanag mo sir.
Sir tuloy sir!thank you sa update
Ang form 2s na metro po ay 3wire single phase at ang form 1s po ay 2 wire single phase, kaya sa form 2S po ay kailangan gamitin ang dalawang coil para completo po ang mtering circuit
Thanks for your informative videos Sir :)
Thanks sir! 👌
ang linaw mo mag turo sir pang pro talaga
Thanks Sir for the basic information and knowledge on electrical grounding system that benefits every electrical practitioners. Unfortunately, it is sad to mention that major points (per latest PEC) are not being observed and considered at all in building elect. installation in the province (in my area):
1. No equipment grounding conductors (EGC) or circuit protective conductor (CPC) installed. For single phase LN system, TNC is adapted even up to internal building installation which is dangerous in the event of fault or disconnected neutral.
2. For street lighting system, steel poles are without bonding to earth. Earthing connection is provided by utility at point of supply only.
3. Lightning protection system are not introduced for taller buildings. (above 3 floors)
4. As part of technical documentation in electrical design, I observed that in the short circuit calculation, the determination of minimum Isc levels are not included (only the max KAIC level is determined). Such are used to classify MCB types (B, C, D, Z) or to calibrate
MCCB magnetic trip settings if adjustable and electronic types.
5. Other electrical standards such as method of installations and proper materials.
I know that concerned authorities (LGU and Electric Coop) are approving and issuing electrical permits with the coordination of contractor/PEE. There is no proper implementation and work checked on the actual installation which are in violation of latest PEC provisions. This are my observations and comments as a retired OFW on the prevailing electrical practices here in my area and I hope that these malpractices can be corrected.
RGG
nice explanation... thank you boss..
madaling maunawaan sir
Salamat sa explanation sir
nice....yan ang tama sir....good good
gawa ka sir ng mga common error of electrical installation etc.
ganda ng explanation mo boss
Thank you po sa malinaw na explaination.
Tanong ko lang po sir kung ok lang po ba ang BONDING JOINT sa loob na ng bahay pati ang gounding rod. Wala po kasi nakaabang na DISCONNECT MAIN sa labas....maraming salamat po
New subscirber here! Na refresh ako master thanks..