[Troubleshooting] MAX30100/30102 not working | Initializing pulse oximeter..FAILED | LED not working

No red light on max30100/30102 sensor after all connections & programming done
" Initializing pulse oximeter...FAILED" |
"Initializing...
MAX30100 was not found. Please check the wiring/power"
if your serial monitor showing similar output and you are looking for the solution for these issues, then you have stumbled at the right place. this video will help you to solve all these issues.
This channel to share exciting videos of Arduino projects,Electronics and electrical easy diy projects to share with you I hope this projects will be helpful for you to create something new .
Do not Forget to like comment and subscribe my channel.
SUBSCRIBE LINK:-
/ @slideas1
MAX30100 Library :-
www.mediafire.com/file/w4lxn3...
MAX30102 Library :-
www.mediafire.com/file/4mm5wa...
MAX30105 Library :-
www.mediafire.com/file/j1cb3t...
#MAX30100/30102 #Arduino_oxymiter #Heartbeat_Monitoring

[@iotdeveloper9687]

love u bro... its working thank u

[@keralagamingbuddy8472]

the work that you put to post such a useful video , i appreciate it mahn , thanks a lot....❣❣

[@RahulRathore-qy4uf]

Firstly, thank you for this wisdom .Secondly I have a doubt actually the hole from which you are connecting to internal resistor in my module the hole is very small so should I take a risk of performing soldering on a minute hole. Any suggestions??

[@Bob-xk1kl]

Very very very useful, Thanks a lot

[@slideas1]

Thank u

[@ICTBLACKBELT]

මේක සුපිරියක්
දැකපු හොදම එක
intro එක මරේ මරු
මටනම් සෙට්

[@slideas1]

Comment එක දැක්කත් ඇති .....ස්තුති යාලුවා ...😍

[@jhevishramphul6331]

Hello I have the gy max 30100 which is the pink one and it is not working. any fix?

[@rishabhlal8750]

Great video,, I have this doubt that if i just want to check whether the sensor is working or not can i check it by just making the connections (with desoldering the resistors and connecting external resistors) from arduino to MAX30102,,, will the leds glow upon connection without uploading any code to the arduino ????

[@slideas1]

Thanks...yes leds glow without uploding any codes ....

[@raspimari5532]

Great Video! Everything is working know.

[@slideas1]

Thank u....❤❤

[@JackNoble117]

Bro I have a MAX30100 but my sensor doesn´t have the little hole where you put the wire to connect into the resistance. Also, my sensor works in Arduino but in ESP32 not. Do you think if I do this, it will work? Thanks for the video

[@slideas1]

3*4.7k risistor methods is best

[@deepanshusrivastava2316]

@@slideas1 can you tell how to do that in max30100

[@pcmobiletechnicalsolutions8504]

i did the same as shown in the video but still showing fail

[@chamothkaveesha4288]

Machn mm esp32 board ekakt set kare habai mage successfully connect kiyla watenava eth values pennanne 0 kiylane ai e?

[@slideas1]

MAX30102 ekakda?

[@chamothkaveesha4288]

@@slideas1 na max 30100

[@slideas1]

@@chamothkaveesha4288 vedio ake widiyatakarala baluwada?

[@chamothkaveesha4288]

@@slideas1 mage oximeter connected successful kiyla enva eth value eka pennanne 0 kiyl thama oya widiyt kare na habai

[@chamothkaveesha4288]

@@slideas1 machn video eke widiyt kara thama e error ekamai mail eka dapnko bro mekat solution ekak danaganna

[@MrAman778]

I have made the required changes, still the led is nor glowing

[@ankit14245]

I have a max30102 sensor. It is working fine, but the SpO2 % is fluctuating a lot and sometimes goes to -999. How to overcome that ?

[@kamikazeshibarushi8548]

i having the same problem do u have solution for that?

[@ankit14245]

@@kamikazeshibarushi8548 no I have still not found a solution for it. Atleast with max30100 this ain't the problem. The spo2 rate is still stable. I have tested both the sensors but I keep getting this -999 pretty often in max30102 sensor

[@kamikazeshibarushi8548]

@@ankit14245 Thank you for the reply I try to use rubber band but sometime it still give -999 value

[@ankit14245]

@@kamikazeshibarushi8548 I don't think so it's because of the rubber band. There are some other settings that are missing probably.

[@leylagulieffa9644]

hi can you send full code?

[@pcmobiletechnicalsolutions8504]

i did the same as shown in the video but still showing fail

[@manaar_artista6252]

Where can I find the code 😢

[@asimfathekhani]

value is becoming zero when we remove the finger, what to do for that? anyone plz help me

[@jungcookie7041]

Bro I did this but my sensor is overheated what should I do now

[@ayahashem1346]

Hello how did you solve this problem?

[@jungcookie7041]

@@ayahashem1346 I bought modified sensor in online

[@yswathi2141]

It is not glowing for me ... Whta should i do.... It is new one.! Please reply 🙏

[@hadjermekahliaa6132]

Same did you found the solution

[@_Bebsi]

Super bro

[@slideas1]

Thanks bro....

[@_Bebsi]

Code ??

[@slideas1]

@@_Bebsi library examples

[@deepanshusrivastava2316]

Does it worked for you?

[@_Bebsi]

@@deepanshusrivastava2316 yes

[@tokioshiguerra]

code? :(

[@MFleurette]

bro you are cheating!!! your code is so dumb! from Dubai with love