After watching your video I was convinced on ordering the mulch plate. I will be getting it sometime this week and can't wait to add it to my Deere, nice doggo, my beagle loves laying on the grass after a cut I guess she uses it as a back scratcher 😂
You are supposed to put that plastic clip inside the mower deck by the back wheel that makes it much more of a snug tight fit. and the bungee goes in the small hole close to the deck wheel
Best part of the video was seeing doggie! Seriously though, thanks for the review and great video. You helped me make up my mind in just trying the block and leaving my standard blades installed.
Just lift up the plastic discharge cover and remove the front and back hooks connected to the rubber bungee straps and it will come off the discharge opening.
@@tomn5880 - I introduced Tenacity this year. I combine the Tenacity Pre Emergent with a Surfactant and applied it to all of my crabgrass and other weed infestations form last year. I am hoping to get the "best lawn in town" award this year. Time will tell.
I own a JD 130 and I only use the plug when cutting the grass in the summer. Using the plug for fall leaf mulching bogs the engine down and over heats the tractor engine. I have tried raising the deck to its max and it still clogs up. For the fall leaf mulching I just run over the leaves at 3.5 inches and circle around a second time. No plug. My mower mulches much better when I back over the first cut. I use JD Gator blades.
When u installed kit. The left side by rear tire has that clip that clips or slides a small part into the deck. Did you slide n clip that side or just put it in place n clip it on....I have the e100 n I only have the small hole about 2 inches over from that big hole. I see u have hole rite above big hole. My kit tends to sit a little high...I think I might drill that hole u mentioned so I will have some downward pull. I just ordered mulch blades....reviews say it give a little better cut. But your lawn looks amazing for not having mulch blade. Thanks for the info
I place mine in the hole on the tab that you see in my thumbnail photo. I agree that there is not enough downward pull on the cover. The extra hole is likely a good idea. Just account for the path of the rotating blades so that you will not create an obstruction. Also , about the mulching blades, I bought a set this fall. My mower does a much better job mulching grass and leaves with the mulching blades. Here is the link to the blades I am using: amzn.to/3oaK3Jv
I do not let it get too high when I intend to use the mulching plug. I also added mulching blades since I made that video and it helps chop the grass much better. There are links to the appropriate mulching blades below my video if your are interested. Mulching Blades: amzn.to/3sd8xTu Mulching Plug: amzn.to/3I9MrZc
@@BudsSmartHome I'm finding that mulching kits for the X500 series John Deere's are pretty expensive and not really made to go on and back off easily or quickly. Fortunately, I still have my LA-135 and it will accept a mulching plug like this you show, so I think I will hold on to it and dedicate it as a mulching machine for the immediate grounds around the home, leaving the 500 series (yet to buy) for the bulk of the mowing in our field. I appreciate you sharing this video with others. I wasn't sure this gadget would actually work but it looks like it will - good enough for me, anyway. Thanks!
@@BudsSmartHome Bud, wouldn't it make sense to remove the long, plastic discharge shoot when mulching? Also, on my LA 135 deck, I had difficulty attaching the clips because of a small difference in how the holes on the wheel bracket and (esp) the rear end of the deck were situated. I solved this by reversing the clips on the rubber grommets. (yes, I did purchase a JD plug after viewing this video).
@@mic982 Yes. You need to remove the discharge shoot to attach the plug. I hope the JD Plugs works well for you Mic. It's great for mulching leaves as well!
My mower does a better job mulching grass and leaves with mulching blades. Link to Mulching Blades: amzn.to/3oaK3Jv Here is a like to the Mulching Cover used in this video: amzn.to/3I9MrZc
* John Deere Mulch Cover: amzn.to/2NylaTV
I would assume this fits an 42" x300 as well? Can you confirm. Thanks
Although the Amazon description didn't list it, it did fit my X300 perfectly.
@@BudsSmartHome Awesome man! Thanks!
@patkelly2478 ~ You bet! 👍
Awesome video! Very informative and well done. 👍🏻
Hey, thanks Papa Joe!
After watching your video I was convinced on ordering the mulch plate.
I will be getting it sometime this week and can't wait to add it to my Deere, nice doggo, my beagle loves laying on the grass after a cut I guess she uses it as a back scratcher 😂
Yes, Sarah is a good beagle! Enjoy your mulch cover.
Great video! I especially loved Sarah's additional comments!!!
Thanks! Yes, Sarah is the best!
Thanks for adding Sarah to the video :)
Absolutely! She was the real star of the show.
You are supposed to put that plastic clip inside the mower deck by the back wheel that makes it much more of a snug tight fit. and the bungee goes in the small hole close to the deck wheel
Correct! Thanks Mickey!
Best part of the video was seeing doggie! Seriously though, thanks for the review and great video. You helped me make up my mind in just trying the block and leaving my standard blades installed.
Glad that I could help!
I have a John Deere lawn mower 100 series..how do I take off the mulcher plug
Just lift up the plastic discharge cover and remove the front and back hooks connected to the rubber bungee straps and it will come off the discharge opening.
If you are using the mulching plug or cover as shown, why do you need to put the chute back on?
I never took the shoot off because it’s permanently attached. Plus if I want to mow without the plug that shoots already in place.
I use my mulching plug in the fall to chop leaves. I discharge clippings (cut with the mulching blade) to the air during summer.
I use it for fall leaves as well. It does a nice job. Beats the heck out of raking and feeds the lawn!
@@BudsSmartHome We use pre emergent weed preventer, a good quality fertilizer and winterizer. We have the best lawn in town.
@@tomn5880 - I introduced Tenacity this year. I combine the Tenacity Pre Emergent with a Surfactant and applied it to all of my crabgrass and other weed infestations form last year. I am hoping to get the "best lawn in town" award this year. Time will tell.
@@BudsSmartHome If the crabgrass seems uneffected by the treatment then you have goose grass.
@@tomn5880 - Thanks for the tip. Is there an effective proven treatment for this "goosegrass"?
I own a JD 130 and I only use the plug when cutting the grass in the summer. Using the plug for fall leaf mulching bogs the engine down and over heats the tractor engine. I have tried raising the deck to its max and it still clogs up. For the fall leaf mulching I just run over the leaves at 3.5 inches and circle around a second time. No plug. My mower mulches much better when I back over the first cut. I use JD Gator blades.
Thanks for commenting Steve.
So "mulching blades" are not necessary? I can just use the OEM blades and mulch my lawn clippings by just adding the cover?
Yes it’s possible. However, the lawn looks much cleaner when cut with mulching blades.
When u installed kit. The left side by rear tire has that clip that clips or slides a small part into the deck. Did you slide n clip that side or just put it in place n clip it on....I have the e100 n I only have the small hole about 2 inches over from that big hole. I see u have hole rite above big hole. My kit tends to sit a little high...I think I might drill that hole u mentioned so I will have some downward pull. I just ordered mulch blades....reviews say it give a little better cut. But your lawn looks amazing for not having mulch blade. Thanks for the info
I place mine in the hole on the tab that you see in my thumbnail photo. I agree that there is not enough downward pull on the cover. The extra hole is likely a good idea. Just account for the path of the rotating blades so that you will not create an obstruction. Also , about the mulching blades, I bought a set this fall. My mower does a much better job mulching grass and leaves with the mulching blades. Here is the link to the blades I am using: amzn.to/3oaK3Jv
Thank you so much for the great video
Thanks JB!
Any idea how tall the grass can be using this plug to much with?
I do not let it get too high when I intend to use the mulching plug. I also added mulching blades since I made that video and it helps chop the grass much better. There are links to the appropriate mulching blades below my video if your are interested. Mulching Blades: amzn.to/3sd8xTu Mulching Plug: amzn.to/3I9MrZc
@@BudsSmartHome I'm finding that mulching kits for the X500 series John Deere's are pretty expensive and not really made to go on and back off easily or quickly. Fortunately, I still have my LA-135 and it will accept a mulching plug like this you show, so I think I will hold on to it and dedicate it as a mulching machine for the immediate grounds around the home, leaving the 500 series (yet to buy) for the bulk of the mowing in our field. I appreciate you sharing this video with others. I wasn't sure this gadget would actually work but it looks like it will - good enough for me, anyway. Thanks!
You're Welcome Mic 😀
@@BudsSmartHome Bud, wouldn't it make sense to remove the long, plastic discharge shoot when mulching? Also, on my LA 135 deck, I had difficulty attaching the clips because of a small difference in how the holes on the wheel bracket and (esp) the rear end of the deck were situated. I solved this by reversing the clips on the rubber grommets. (yes, I did purchase a JD plug after viewing this video).
@@mic982 Yes. You need to remove the discharge shoot to attach the plug. I hope the JD Plugs works well for you Mic. It's great for mulching leaves as well!
I just bought the S120 and the mulching cover. I cannot get it to fit properly. Suggestions?
The Amazon description states it fits 100, D, L, and LA Series Mowers, plus S240 and Z225 w/ 42" Decks only. The S120 model is not referenced.
@@BudsSmartHome Doesn't "...fits 100 series mowers..." mean it should fit???
@@1rightrev- I’m unsure if the 120 and the S120 are one in the same. Perhaps you can ask the John Deere Dealer
@@BudsSmartHome Thanks for taking the time to reply. I have sent a query into the dealership in our area.
Sorry I could not be of more help Bill.
can you remove the grass shoot for connivance
Yes
What height did you cut it at?
Smoke Stack: I have my deck set at 3 1/2 inches currently. I’m not sure where it was set when I did that particular video.
Do you have standard or high lift blades. Does it matter either or on the blades.
+jimmy neutron I have standard blades. The type of blades do not matter
Why do all these videos not actually show you or show you from a distance which doesn’t do me any good?
I’m not sure what you want to see. If you’re talking about the mulching plug, here is an Amazon link: John Deere Mulch Cover: amzn.to/2NylaTV
What is your "normal" speed to mow on the JD D100?
Right. But what gear do you favor for most situations?
My mower does a better job mulching grass and leaves with mulching blades. Link to Mulching Blades: amzn.to/3oaK3Jv Here is a like to the Mulching Cover used in this video: amzn.to/3I9MrZc