hyosung FI enging light
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2024
- Easy way to get the fault codes out of your Hyosung
If you like this video please like and Subscribe me
Also take a look at.. SHANE the mechanic on Face Book
CODE Malfunction
11_______ Main throttle sensor 12_______ Inlet air pressure sensor 13_______ Inlet air temperature sensor 14_______ Water temperature sensor 21_______ Crankshaft sensor 24 & 25___Speed sensor (24 then 25, repeatedly) 31_______Vehicle-down sensor 32_______Subthrottle sensor 33_______Oxygen sensor inactive (Europe) 51_______Ignition Coil #1 52_______Ignition Coil #2 56_______Radiator Fan Relay 62_______Subthrottle valve actuator (sensor in range but not responding) 64_______Air switching valve 67_______Oxygen sensor heater (Europe) 94_______Oxygen sensor out-of-range
So I just got the factory tester in the mail because my 2016 gtr was constantly blinking FI every few seconds. Tested it and it said no code, after more research it’s normal for the F1 to do that which I think is dumb! I will make a video if requested tomorrow
Hey mate, I'd be keen to know more about this. My 2014 GT650 has a blinking FI light but not sure if there's actually any issue?
My gt650r 2016 blinks FI light when its not started. Once i start it, the error goes off.
The cooling fan was off, so I don’t know the mechanic here what to do. He turned it on, but the f1 sign was shown and the lamp does not always light up after operation, and the radiator is very hot, as it is always so hot that it has holes for water smuggling and the holder of the bike was working when I download it now it does not work without it I raise the entire stand except for the upper position, so what is this please?
Yo he hecho lo mismo que en el vídeo, y me salió solo la letra c. Y después ya no me arranca. Habré quemado algo?
Found my fault code, 2 5 2 5 2. My hgpsing FI light blinks in sequence and thays my sequence which is code c25. I have a gv250 efi aquila
Would leaving the switch plugged in cause the battery to drain?
Hi Sal .. as far as I no . yes when the FI light is on flip the switch to figure out the code.. I do not no if it would drain the battery if the switch is turned on .. in the off position it will not ,, thank you and please subscribe
So this only can be read when the light comes on? Do you flip the switch on when the red light comes on then it will tell you the fault code. I have a gv250
yes
@@shanethemechanic4174 yes thank you
how did you go??
@@shanethemechanic4174 good it was random misfire 2nd cylinder, replaced plugs and coil and it fixed it!
@@shanethemechanic4174 hey bro my hyosung gt650r started showing f1 error and when it comes bellow 3rpm ideal goes down and like seems as if the bike gonna go off. And one more thing is when i start the bike i have wait yill the rpm rises like 30sec
I get an F1 mark on the screen and there is no mechanic here that understands haysong and I always notice a hole cut in the water radiator and I repair it and it repeats. Now how do I fix the f1 and find out the error please send me the method because there is no mechanic here who understands haysong please
Literally took mines apart and forgotten which wire connects where 😢
Good vid. Tried this and it showed nothing. I saw a vid that said you can stop and just connect wires then, which also did not work. Then a comment said with Delphi ECU to short it before you start and it starts fine then hold select for 15 seconds. I have tried all ways and nothing shows the error code. Do you have any other suggestions?
Not sure if you followed the directions for the Hyosung. the reason I wired a switch up to the check light is that as you can only check the condition as long as it is live , so keep riding the flick the switch,, note if the check connector is bridged the bike will not start , hope that helps
shane the mechanic thank you for your reply. It seems some can be started while bridged after looking at forums. I tried your way with a switch and also bridging while it was on and before starting and nothing has worked. Seems strange.
@@shanethemechanic4174 did it too my 2011 250 and worked well bike started even though bridged
@@tier8369 what did he do? Make a switch like this?
@@shanethemechanic4174 I tried every way mentioned here and have no fault codes showing. I do get 25 flash up rear coil when I start the bike with or without the switch. I changed the coils and it is the same, I crashed the other day low speed in the city now the bike cuts out losing all mpower checked all connections battery etc..Any ideas?