Common Mistakes in Logisim - Red and Blue Signals!

How to fix red or blue signals in Logisim.

[@lutherevangelista605]

This videos is a lifesaver for university students!

[@The_Real_Karim]

Thank you so so so much for this video! I was stuck for two hours trying to figure out what an issue with a wire was, and this video helped me out so so much! You really really saved us all! ❤

[@gamelon3554]

Thanks a lot, I had no clue about the "Simulation Enabled" thing, your video saved me lol

[@adamadamus2714]

A Super thank you for the video. These are small details wich no one really lights out.

[@diabianeyah]

You’re welcome. Thank you for your kind comment.

[@chriskantz5163]

Thank you! was starting to sweat over my project

[@imRJD14]

Thanks a lot you saved me an hour

[@esvanadium7632]

Thank you so much sister. May Allah bless you

[@vSoloist]

You really saved me! Thanks a lot

[@sarahal-ateiyah6581]

شكراً للفيديو المفيد،. موفقة بانتظار مزيد من فيديوهات مشابهة تلامس احتياجات الطلاب الجامعيين

[@diabianeyah]

شكراً على تفاعلك

[@deto_san590]

I may have loss many grades without this video, thank you so much doc!

[@diabianeyah]

Thank you for your comment. Happy to help.

[@prodjvenchy]

thanks! i spent an hour and half figuring out why my totally correct circuit was red till i found this video.

[@isaacsaxonov926]

Is there any reason that an and gate would output a red wire after recieving two binary values? I have no idea why mine is and could attach a picture if it helps.

[@diabianeyah]

Ensure that it is 2 input AND.

[@ibado5592]

thank you so much that was really helpful , from algeria

[@MyteeT]

thank you
you saved my grades

[@ExpertTutor]

Thank you helped a lot

[@learn9122]

Thank you. But sometimes it causes an error when you use not gate. the wire works fine but when you add a not gate it says conflicting inputs?

[@diabianeyah]

Double check the pins and/or the wires connected to the not gate and make sure they are only 1 data bit each. You can see that in the settings box on the bottom left panel. The not gate itself by default has 1 data bit. Make sure that you do not change that.

[@Wingates1414]

Thank you. You gave me a head start.

[@diabianeyah]

You're welcome :)

[@maryamarif9258]

ااهه اححبببك ثانكييييو موووت😔💜💜💜💜 thank you so much you helped a lot

[@minhtris21]

Thank you so much!! you made my day

[@diabianeyah]

I'm glad I can help :)

[@StinkyDurian]

Thank you so much !!! U saved my university assignment

[@diabianeyah]

You're welcome :) Good luck.

[@Verda58]

Thank youu

[@kaitlyncentral]

TYSM

[@adityaranjan2024]

Thankyou 🥰

[@vidsforfun5155]

What do i do when having an oscillation apparent?

[@diabianeyah]

Make sure you don't have feedback. In other words, make sure the output is not connected to the input in one way or another.

[@vidsforfun5155]

@@diabianeyah I didn’t. I was constructing a JKFF with the correct wirings and components but then when my inputs are both 1, the oscillation apparent would appear. Do you perhaps know what’s wrong with it? I’ve searched this problem in youtube and some say JKFF is impossible to simulate but in real life, it would theoretically work. I’m confused 🥲

[@diabianeyah]

@@vidsforfun5155 When both inputs of a JK flip flop are 1, then the output will always toggle. Your work is correct.

[@lamaz2809]

i still have blue signals in the output I tried everything is connected with mul

[@diabianeyah]

Did you check if Simulate -> Simulation is Enabled? and Simulate -> Ticks enabled is ticked?

[@ddeungromi]

Ty so muchhhh!!!

[@diabianeyah]

You're welcome :)