#RC4WD
ฝัง
- เผยแพร่เมื่อ 10 ธ.ค. 2023
- #RC4WD Bully II MOA 1st run 12/10/2023
Music: NEFFEX
It's Only Worth It if You Work for It (Instrumental)
Electronics
Hobywing Fusion SE 1800kv front
Hobywing Fusion SE 1800kv Rear
Savox SW-1210SG Waterproof servo
Ovonic 850 3S Lipo
FlySky FGr4S v2 Rx
Flysky NB4 Tx
Tire/Wheels:
Proline IBEX G8 front
Proline IBEX Predator Rear
Amazon 2.2 Carbon wheels
Crawler Innovations 5.5 Comp cut medium Front
Crawler Innovations 5.5 Standard cut soft rear with trim ring
22mm SLW Dlux Hubs
Chassis
Reefs 27mm Servo Horn
RC4WD Stock Bully 2 MOA Kit
RC4WD Stock Bilstein Shocks 45wt front, 79wt rear
Traxxas 5225 long rod ends on some links
Team KNK Hardware
Body
V ViViD Carbon fiber metallic blue wrap
Axles
Dlux Brass Knuckles
Dlux Aluminum upper arms single / Proper ackerman
Dlux Tungston Slugs
Dlux heaveir brass lower arms
Transmission
RC4WD Stock Bully 2
#dlux_fab_rc
#hobbywingfusion
#ovonic
#prolineracing
#rc4wd
#savoxservo
#teamknkhardware - ยานยนต์และพาหนะ
❤
Amazing crawler, nice video bro!)😃👍
thank you - I appreciate the comment
So sick I half to get one now 👌🏻
I held off for a while until a friend let me drive theirs and i was hooked.
NIce !!!
Thanks!
I also have the Bully 2 and its so capable of climbing just about anything, but when I added my Dluxfab knuckles it became a beast. I'm glad to see someone else running the knuckles. 💪🏻😎👏🏻👏🏻👏🏻🤣😂🤣🪨🦎 You have a new sub👍🏻
Thanks for the dub. Its becoming my favorite rig. I think next upgrade will be the DLUX dravtec shocks....
Just got a bully 2 too busy to watch Al this right now but saved and subbed…very cool video and rig looks like a sick spot!!!
Awesome - Thanks for the comment! Im trying to keep the vids short.. I dont have much of an attention span hahah.
Nice
Love the bully 2, nice video I’ve just literally ordered one of these for myself 😅
awesome - It quickly became one of my favorite crawlers. I've only had 4 or 5 battery packs through it so far.
How do you make the 2 fusions run off the 1 battery?
I made a splitter off the battery to feed each motor. You can buy one, im sure.
@@grvtyboyRC ahh like a Y lead.
why no brushless ?
I do have brushless . Fusion SE for front and back. If you asked "why go brushless?" i felt the slow crawling and slow start is really effective on the fusions. There's a lot of brushed choices but when I compare my friends stock brushed motors and ESC in his bully versus my fusions, there's no comparison in terms of the ability to crawl super slow and instant torque. The brushed motors still hesitate when in between magnets and can cog and hesitate (stock electronics).
There's those that will swear by brushed and the level of control, but its clearly not the case with stock electronics on the bully. Maybe I'll do a video of that since I have access to a stock bully 2 and mine with the fusions.
How do you like the fusions in the Bully 2?
love 'em. Low speed control and slow start are amazing. Much much better than stock brushed motors and stock electronics....i have tried a stock set up. . I have the ability to adjust underdrive on the fly from the RX and also am set for rear dig and front dig which comes in handy. The Fusion SE motirs have too much wheel speed for me, so i have to limit the throttle travel.
@@grvtyboyRCThat is awesome. I'm currently building a Bully 2 and have a brushed setup for it but man i really like the idea of brushless. Any modifications needed to make them fit?
@@BigD3D I did connect the rear lower links and shocks on the outside on the mounts on the axle side rather than on the inside. I did have to slightly bend one of the front links as well to fit more comfortably around the motor. Very slight bend.
Im trying to figure out how to mount the dlux knuckles on mine. Is there any how to videos? When installed the wheel pin hole isnt out far enough. What am i missing here?
Yeah took me a bit to figure it all out. I only used this video.
th-cam.com/video/nr9-5i0ZWH4/w-d-xo.html
Also the stock bully wheels wont fit around the knuckles. I bought aftermarket 2.2's that would fit.
Thank you.
Is there another part i need to get to make these work? Different axels? Lol im so confused with these knuckles.
@markless125 the video shows different axles but the concept is the same. You could reach out to the dlux fan FB group page or email dlux direct to see if they can help out.