I like that you used your imagination to make your tool holders. A stop block behind the tool holder will keep it from coming off the wall when you pull up on screwdrivers.
I think the peg-board-to-French-cleat transition is just a part of work shop growing pains. I finally ditched the peg board and got my cleat wall up, so thank you for the great fixture ideas!
Nice work! The FC offers some nice flexibility for moving the sets around. Personally, I still use peg hooks (with essential locking clips), but my most strict rule is that the most common tools are to be in the easiest accessed part of the wall. The least common further away from my arms reach. My go-to is....I really like a shallow 3" deep lightweight cardboard box for all common tools (hammer, screws, pliers, adjustable wrench, cordless drill, drill bits, common screwdrivers) and I leave them in that box for common around the house jobs. I got the idea from how the dentist does it with his common tray of tools. I just keep my "tray" ready to go anywhere in the house and prevents me from making a trip back to the garage for a tool I forgot to include. Of course, I will add a specific selection of tools to my common tray from my pegboard as I need. For instance, for electrical work (wire cutters, wire strippers, electrical tape, needle nose pliers, etc) I will add those in addition to my common tools in my tray.
The trick is to make some of the holders so that you can pull out the tools to the front instead of lifting them out upward. Or at least diagonally. Then you can put those holders beneath the other ones and never hit anything above. It lets you use the space more efficiently. My shed is only 8x9 feet, gotta use every tiniest nook.
think about putting the holders at a slight angle. that way there is way less vertical dead space since you dont need clearance to pull it out. your screwdriver holder for example if you were to slightly angle it towards you then you can put a second rack right above it. in my small shop thats a must!
I did a similar chisel holder but for about 10 chisels. I routed the grooves and screwed clear Perspex over the front so I can see at a glance which chisel to grab. Turned out fantastic.
I like what you did. For things like screwdrivers, I don't think one row of tools per holder is enough. Make the holder deeper to hold 2 or 3 rows. You get more tools per square foot of wall. I've also decided that most French cleat brackets need to include a lip goes pretty tightly under the flat bottom of the cleat board. Otherwise some brackets will lift out of the cleat when you lift the tool from it's holder.
I like the FC system, but I'm finding that the holders can pop off when you pull a tool when your not quit strait up and clean the holder. I'm going back and placing my cleats on the wall closer together and making a locking tab so the holder can't clear the wall cleat. nice job. the system give a lot of options.
Just found your channel while browsing for storage ideas. I like your take on the FC system. The plier rack was cool, but my favorite is the chisel holder. With your setup, the individual chisels are easily accessible, but the business end is also covered. That is great for me, as I am the first guy to hit a corner of sharp stuff with my hand.
The French Cleat & your video saved my storage problem as I have no floor space & only 22 inches of wall in 3 places which I can hang 2-3 long 7 ft x 1in. boards which gives me 6 to 9 boards to hang stuff on! : ) Thank You!
Thanks.. A great start. When will you show me how to make the remainder? I need to get rid of my large tool chest, my homemade rolling clamp storage and anything else that can go on the wall. Looking forward to the next instructional. Thanks again
I’ve watched many many videos on French cleats. I’m still waiting for some one to tell me the exact dimensions of each cleat and the exact spacing between them!
Dave does really careful work; great job! Like the way your create and use jigs so often; very efficient. I'm building a similar French cleat system for my garage and shop but instead of such a uniform wall of slats I simply put a board with 45 degree angle wherever it's needed around the shop and garage. In this way I don't have to make an array of slats that may or may not be too crowded for what I need. Further, I'm just using scrap wood to keep it all inexpensive.
The Narex chisels have a 7/8” retainer, you can just drill 7/8 holes. Anything larger just mortise the two sides out. 7/8” will hold firmly while still give easy access.
Thanks. Truthfully, I couldn't say how I arrived at the width of the cleats other than it looked about right to me. They seem to be working well, but that doesn't mean that I won't ever trim them down if I decide it would work better. My shop will probably always be a work in progress.
Vertical storage frees up your horizontal space. French cleats are the way forward but watch how much space you put between each cleat as you don't want to inhibit tool removal from the cleats below. Thanks for posting.
That's a "dado stack". Two outside blades and a variable number of chippers between them to cut a wide slot. I understand that they are illegal to sell in many countries.
Great work on those French Cleats, i have some of them with Cupboards on them, and i'm now thinking of doing a French Cleat Tool Wall in some space i have. Thanks for the Tool ideas. New Subscriber. Barry (ENG)
I have watched lots of these French cleat videos, but I can't understand the need for glue. I just screw them in and they're done. Nothing comes loose.
Hey Dave . It's a blast making these holders , isn't it ? I put french cleats in a cabinet I copied from Measured Workshop on YT . They're way better than pegboard if you ask me . Nice video.
That is a dado stack. 2 outside circular blades and assorted chippers to establish width. I've heard that they aren't legal for sale in some countries.
laura palmore You can certainly make them from 1x_ material. I have used solid wood cleats to hang cabinets. I think plywood might be cheaper but I would price it out before deciding.
The strips are 3 1/2' wide at the widest (front) part and spaced 3" apart. Truthfully, the widths and spacing were pretty arbitrary. I was making them up as I went along based on the material I had and the space. It's very possible I may rip them narrower or re-position them in the future.
Thank you so much, Dave, for sharing such an inspirational video. I will definitely retire my pegboard, soon. By the way, what is the height of the french cleat? Also, what is the space between them? Thanks again, Dave ;-)
Hello. I am French. I watched your video with a lot of interest. Could you indicate the dimensions of the cuts of the cleats. I imagine that the angle is at 45 degrees. What spacing did you use between each cleat? Thank you
Did you mean: pliers Search Results Featured snippet from the web Noun. 1. plyers - a gripping hand tool with two hinged arms and (usually) serrated jaws.
Be careful with the nail gun u keep your fingers too close. Sometimes nails getting out in opposite direction. It happened to me when it penetraited through my nail.
Спрошу по Русски так как не понял зачем нужно было огород городить с переходом на французские планки если на первоначальном варианте выставочного планшета было всё что нужно для навески любых конструкций с помощью ввёрнутых крючков?
Hi Sergey. It's not needed to switch over to slats. It is just what I prefer. The pegboard works but the hooks fall out sometimes and not every tool has a manufactured holder that works with pegboard.
Good idea with the chisel holder, despite being very complicated, it is very safe
I never seen anyone use a table saw as good as this guy!!
I like that you used your imagination to make your tool holders. A stop block behind the tool holder will keep it from coming off the wall when you pull up on screwdrivers.
I think the peg-board-to-French-cleat transition is just a part of work shop growing pains. I finally ditched the peg board and got my cleat wall up, so thank you for the great fixture ideas!
Why not a combination of both? Both have advantages.
oh that's a good idea I never thought of... square screwdriver holder. seems way easier than trying to drill holes and make it look nice
Nice work! The FC offers some nice flexibility for moving the sets around. Personally, I still use peg hooks (with essential locking clips), but my most strict rule is
that the most common tools are to be in the easiest accessed part of the wall. The least common further away from my arms reach.
My go-to is....I really like a shallow 3" deep lightweight cardboard box for all common tools (hammer, screws, pliers, adjustable wrench, cordless drill, drill bits, common screwdrivers) and I leave them in that box for common around the house jobs. I got the idea from how the dentist does it with his common tray of tools. I just keep my "tray" ready to go anywhere in the house and prevents me from making a trip back to the garage for a tool I forgot to include. Of course, I will add a specific selection of tools to my common tray from my pegboard as I need. For instance, for electrical work (wire cutters, wire strippers, electrical tape, needle nose pliers, etc) I will add those in addition to my common tools in my tray.
"i dont like pegb oard, so i took it out." and this is the best answer ive ever heard about anything. :)
I am so glad to see this today. Was going to make a holder for my files tonight
Awesome fun to watch NOW Build!!! thank you for showing your work
The trick is to make some of the holders so that you can pull out the tools to the front instead of lifting them out upward.
Or at least diagonally.
Then you can put those holders beneath the other ones and never hit anything above. It lets you use the space more efficiently.
My shed is only 8x9 feet, gotta use every tiniest nook.
In case anyone is still wondering, the music is Accidents Will Happen - Silent Partner. You're welcome! (great video btw)
Really like the chisel holder. Slick!
think about putting the holders at a slight angle. that way there is way less vertical dead space since you dont need clearance to pull it out. your screwdriver holder for example if you were to slightly angle it towards you then you can put a second rack right above it. in my small shop thats a must!
I did a similar chisel holder but for about 10 chisels. I routed the grooves and screwed clear Perspex over the front so I can see at a glance which chisel to grab. Turned out fantastic.
I really liked the chisel holder where you can see which is which.
I like the way that you painted the rails the same color as the walls. Really nice!😁
I like what you did. For things like screwdrivers, I don't think one row of tools per holder is enough. Make the holder deeper to hold 2 or 3 rows. You get more tools per square foot of wall. I've also decided that most French cleat brackets need to include a lip goes pretty tightly under the flat bottom of the cleat board. Otherwise some brackets will lift out of the cleat when you lift the tool from it's holder.
Dang , you are quite the craftsman ! 👍🏽
great job, all good designs, loved video.
I was specifically looking for ideas on hanging chisels on a French cleat. I like how yours are enclosed!
Thanks. It's important to me to keep the cutting edges covered since I'm clumsy.
I like the FC system, but I'm finding that the holders can pop off when you pull a tool when your not quit strait up and clean the holder. I'm going back and placing my cleats on the wall closer together and making a locking tab so the holder can't clear the wall cleat. nice job. the system give a lot of options.
Just found your channel while browsing for storage ideas. I like your take on the FC system. The plier rack was cool, but my favorite is the chisel holder. With your setup, the individual chisels are easily accessible, but the business end is also covered. That is great for me, as I am the first guy to hit a corner of sharp stuff with my hand.
Thanks Andrew. Exposed sharp edges are a problem for me too.
I like and approve of all of it and will give Pegboards a second and last thought. This is better!
Excelente trabajo maestro gracias por compartir sus conocimientos, es lo que necesito hacer saludos
Awesome job
I have a peg board I have been procrastinating to put up on my workbench. I definitely am switching to french cleats now. Should be easier. Thanks
Nice work, both the wood and video. I'm in the process of doing french cleats myself....great inspiration from you. Thanks!
The French Cleat & your video saved my storage problem as I have no floor space &
only 22 inches of wall in 3 places which I can hang 2-3 long 7 ft x 1in. boards which
gives me 6 to 9 boards to hang stuff on! : ) Thank You!
Thanks.. A great start. When will you show me how to make the remainder? I need to get rid of my large tool chest, my homemade rolling clamp storage and anything else that can go on the wall. Looking forward to the next instructional. Thanks again
Thanks Mr. Harshberger, I´ll try to do it!!
I’ve watched many many videos on French cleats. I’m still waiting for some one to tell me the exact dimensions of each cleat and the exact spacing between them!
Septimus Pretorius check out "Which French Cleat style is right for you by: A Glimpse Inside.... best ive found yet hope it helps
Dave does really careful work; great job! Like the way your create and use jigs so often; very efficient. I'm building a similar French cleat system for my garage and shop but instead of such a uniform wall of slats I simply put a board with 45 degree angle wherever it's needed around the shop and garage. In this way I don't have to make an array of slats that may or may not be too crowded for what I need. Further, I'm just using scrap wood to keep it all inexpensive.
Thanks! I agree, scrap wood is the way to go for this kind of thing.
Watched and subscribed. Excellent and thank you
I just subscribe to any woodworking channel I find. I hope it's a good vid!
great video instruction and ideas!
The Narex chisels have a 7/8” retainer, you can just drill 7/8 holes. Anything larger just mortise the two sides out. 7/8” will hold firmly while still give easy access.
I've been thinking of reorganizing my tools also. You've given me some good ideas. thanks
Like what you did out of scraps. Why did you use such large cleats on the wall since you didn’t add more support screws?
Thanks. Truthfully, I couldn't say how I arrived at the width of the cleats other than it looked about right to me. They seem to be working well, but that doesn't mean that I won't ever trim them down if I decide it would work better. My shop will probably always be a work in progress.
Vertical storage frees up your horizontal space. French cleats are the way forward but watch how much space you put between each cleat as you don't want to inhibit tool removal from the cleats below. Thanks for posting.
Great video. Just wonder what saw blade you where using for the screwdriver holder? Kind type ???
That's a "dado stack". Two outside blades and a variable number of chippers between them to cut a wide slot. I understand that they are illegal to sell in many countries.
You will have less waste in cutting the cleats if you make the first cut wider and cut them in half. You get two cleats with little or no waste.
Phwarrr! This is next-level mate!
Great work on those French Cleats, i have some of them with Cupboards on them, and i'm now thinking of doing a French Cleat Tool Wall in some space i have. Thanks for the Tool ideas. New Subscriber.
Barry (ENG)
Thank you, Barry.
A lot more work to do? Or a lot more fun? ☺️
What glue did you used sir?
Superb. I really need to get around to doing this in my shed.
Thanks
I have watched lots of these French cleat videos, but I can't understand the need for glue. I just screw them in and they're done. Nothing comes loose.
Genial. Empecé el bricolaje por ver este vídeo.
Nicely done
Excellent idea, I'll give this a go, cheers..
Nice! Good job!
Greetings from France, well done !
very good !
Bravo, très bon travail.
Good job. Just asking where can I find this music that you first play please.
Thanks. The music is from the TH-cam audio library. I looked, but I apparently deleted the file after editing so I don't know the name.
Great ideas
Hey Dave . It's a blast making these holders , isn't it ? I put french cleats in a cabinet I copied from Measured Workshop
on YT . They're way better than pegboard if you ask me . Nice video.
Thank you!
Elinize emeğinize sağlık güzel olmuş usta 👍🏻☺️
Great video!
Thanks John!
Muy buen trabajo, felicitaciones y gracias.
Ive tries looking for tips on painting the FC, did you paint the sides on the plywood if so how?
plz which circular table saw are you using?
Excelente...Saludos desde Honduras hermano
Great job
Excellent
What is the name of blade that you used in 1:48 ?
That is a dado stack. 2 outside circular blades and assorted chippers to establish width. I've heard that they aren't legal for sale in some countries.
ESPECTACULAR
this is on my list of things to do...thanks for the tips!
You're welcome! Thanks for watching!
Can a French cleat system be made from 1x 6 or is it necessary to be 3/4” plywood?
laura palmore You can certainly make them from 1x_ material. I have used solid wood cleats to hang cabinets. I think plywood might be cheaper but I would price it out before deciding.
te quedo muy bien, me gusto mucho
I found the French Cleat System filled with dust and sawdust so I went for the peg board as it’s a lot cleaner.
What was the size of the strips you mounted to the wall. You have cut sizes and lengths
Thinking of doing this today!
The strips are 3 1/2' wide at the widest (front) part and spaced 3" apart. Truthfully, the widths and spacing were pretty arbitrary. I was making them up as I went along based on the material I had and the space. It's very possible I may rip them narrower or re-position them in the future.
you can just rip a 2x4 at a 45 and it works just fine. that's what i did.
Ben fatti. Bravo. Potresti upload a PDF dei modelli con le misure ? Grazie
Thank you so much, Dave, for sharing such an inspirational video. I will definitely retire my pegboard, soon. By the way, what is the height of the french cleat? Also, what is the space between them? Thanks again, Dave ;-)
Hello. I am French. I watched your video with a lot of interest. Could you indicate the dimensions of the cuts of the cleats. I imagine that the angle is at 45 degrees. What spacing did you use between each cleat? Thank you
Hi. The angle is indeed 45 degrees. The cleats are about three inches apart.
Thanks
Very cool idea....I hate peg board too!
5:45 I love that push stick.
What is that "splitter" on your table saw?
That's the splitter that came with the saw. The plastic guard broke years ago.
I thought I was on a DIY woodworking site.....but I guess I got a radio channel by mistake !
amazing
Wich table saw do you use?
It's a Delta 36-650. A basic contractors saw that I bought new in 2002.
Shoot Shoot Kill Kill sounds like a great name for a game. :)
Did you mean: pliers
Search Results
Featured snippet from the web
Noun. 1. plyers - a gripping hand tool with two hinged arms and (usually) serrated jaws.
This video must have been made before any safety gear was recommended on the table saw.
Be careful with the nail gun u keep your fingers too close. Sometimes nails getting out in opposite direction. It happened to me when it penetraited through my nail.
Great video. Thanks. Subscribed!
Thank you!
👌👌👌
Genial
Why do something properly when you could use a nail instead?
Отлично ! Veri good ! 👍
Ok 👌
Спрошу по Русски так как не понял зачем нужно было огород городить с переходом на французские планки если на первоначальном варианте выставочного планшета было всё что нужно для навески любых конструкций с помощью ввёрнутых крючков?
Hi Sergey. It's not needed to switch over to slats. It is just what I prefer. The pegboard works but the hooks fall out sometimes and not every tool has a manufactured holder that works with pegboard.
@@DaveHarshberger да прекрасный способ установок. жаль пыль сильно набирает.
Bonjours, magnifique je prend note.
Valeu
Those tools you use to strip off the angles on nuts and heads of bolts.....They are Pliers; not plyers
Great video! Thank u for sharing :)
Nice simple build
Cheers
Tim from Wood 4 Nothing
Ima make a french cleat holder that holds my french cleats.
Flat head screws! The Horror!
Thanks for the org.
система хранения 21 века TOOLBOARD